วีดีโอ

Same procedure opposite direction and simply push it back in place 🙂

I didn`t have to remove the center dashboard vent jet.If any problem appears then i promise to make a video about it too. 🙂

Hi there! The P0402 code means that your ERG-valve is stuck open. You can try to erase the code and make a new alignment with the throattle body. If that works then your switch had a bad day and caused you the trouble 😄 If that doesn`t work then your EGR is done unfortunatly 🤗

@@mdrc3288 do you know how to resolve P0401 code? EGR insufficient flow

@@ibrahimsalah5999 I suspect that your EGR valve is done! 😕 The P0401 code means that the plug of the valve colapsed and there for stuck closed. That is why there is no flow!!! Unfortunately it looks like you need a new EGR valve. 🤗🙂

@@mdrc3288oh man that’s a shame. You’re certain even a clean from throttle body to egr components won’t resurrect it?

@@ibrahimsalah5999 I`m sorry...unfortunately not.

It is frustrating though when you look on the engine for the first time and see no screws and clips to set it free!!!! 😅😜😎✌

You are welcome 🙂 I`m glad i could help you out of this situation ☺😉✌

Thank you very much 🙂This is just a technique because i like to make things ``bulletproof``. I`m sure there are more easy and simple ways to restore the panel.Take good care of that W124. Those cars deserve to rule the streets for many years to come! 💪😉✌

Δεν θα το βρείς και δεν θα το αλλάξεις γιατί πολύ απλά δεν υπάρχει!😄 Δεν έχουν φίλτρο λαδιού αυτά, μόνο τα λάδια αλλάζεις 😉😃☝

You are welcome 🙂👍

Thank you very much sir!🙂If the system is completely empty it should require 5.5Litres...BUT...there is no way that all the pipes and the tunnels around the engine will be completely empty(unless you find a way to drain it)🤗I believe that around 4Litres of coolant can be changed!😀☝

Estoy usando el traductor de Google para responder: ``Usa algo de WD40.Podría ayudarte`` 😉

Very kind of you Sir 🙂 I`m glad i could help you out!!🤠✌

Well it`s not important because every case could be different. You have to take measurements on your breaking and choose the size of a drill that will cover the hole broken area. Only then you will be able to know what size of screw is necessary.🙂😉✌

Hello 🙂 My car douldn`t get the temperature up and had always around 70C. This means that the thermostat stuck open. In your case the thermostat stuck closed and the radiator coolant liquid doesn`t flow through the system. Do not drive the car while overheating because it could damage your engine head gasket. The repair could get out of control.Replace your thermostat immediately and keep an eye on your fan too. The fan and the thermostat are responsible to keep the engine temperature around the 90C area. I hope to help you out and not be to late to save this ``KILLER`` engine your IBIZA is equipped!! 😉✌

@@mdrc3288 ah makes sense! Cheers for taking the time to reply, I'll swap it this weekend .. it's my sons car not mine so in some ways its even more annoying as I'm now a taxi :-D

@@jivetolkein 😅😂... You are welcome. I`m glad i could clarify things . Cheers 🍻

Thank you very much my friend! 🙂✌You could use some medium hardness spring on your shocks while filling up with 1000 to 1200 cst silicone oil. Use a smooth engine that revs up to 30000 rpm maximum. 😀☝Depending on the surface you are running , adjustments will be necessary on the springs. The behavior of the car will be polite and you will be able to attack full throttle in most cases.😉👌

😅😂...ξύπνησε το και θα σου ξυπνίσει ακόμα περισσότερα αυτό! 😉👌👍

😊😉✌

Hi there Those cars belong to the Volkswagen Audi group (VAG). There for they have a folkswagen engine.You need to find the code of your engine on the car license (mine is BBZ for example ). Once you got it simply type on Google < BBZ engine air filter> and i`m sure you wil get a lot of options to choose from. Hope this was helpfull. 🏁🙂✌

I use Google translate to answer : Çok teşekkür ederim! Rica ederim.Sol taraf gayet iyi durumda sökmeye gerek duymadım.Yine de aynı görünüyor ve aşağı yukarı aynı prosedür olmalı (I hope it make sense )🤗😄🙂✌

You are welcome! 🙂👍

The small lamp is a simple ``PUSH OUT`` and ``PUSH IN`` procedure. It can be seen at 1:02 of this video 🙂✌

@@mdrc3288 I mean that small lamp holder. Small plastic part. OEM: 6L0945231

you also couldve mentioned what bulb it is.. i think its w5w

Thank you very much for this advice@@pkersoul 🙂👍

It does work!

Thank you very much ☺ You are welcome 🙂✌

Check the fuse first but it could also be low liquid in the hydraulic system. Check the level and add as necessary. The ECU system on those cars is hardening - or making more heavy the steering when the speed increases.🙂😉👍

@@mdrc3288 thank you

@@neckaromaw1810 You are welcome. 🙂

@@neckaromaw1810 u fixed it? Or know what the problem is?

@@earlygamer9106 no, fuse is ok and the liquid is ok. It still beeps 3 times and flashes every light. 🤷‍♂️

Both have been purchased on ebay. I can only remember that it was a UK based seller. You are welcome 🙂👍

I`m using google translate to answer : I`m going step by step to bring this bike back on the road.If it's necessary to make a differential maintenance then i make a video about it.🙂😉👍

i`m using google translate to answer: `` I`m changing the `Golden Sebring` back to the original exhaust. 🙂🔧

Well...i wouldn't recommend the material and the technic i'm using in this video for a door panel because it`s curvy. I can only recommend it for flat surfaces like shown .You better ask a local paint shop for advice about this so you can use a more suitable material for curved surfaces.

Well...painting plastics of a Mercedes interior is not a good idea. They have mostly soft high quality plastics and the result will look very poor or even destuctive. What ever you do on on a Mercedes dashboard for cracks ,it will look like a scar.There is nothing to much the material of the dashboard.It is better to order a blanket and protect the rest so no more cracks appiar.🙂😉✌

@@mdrc3288 thank you for your swift reply i ment the hard plastic parts like de plastic covers that are likated where the front seatbelds sit

@@peterjanvanbijnen226 I`m sorry but i have no solution for this one either ...🤗

Thank you very much! 🙂👍

Thank you very much.I`m glad you like it! 🙂👍

You can see the result in my next videos.It looks amazing!(the answer came after translation with google translate)

Yes it is possible.You can use even 18 rims on this bike.(The answer came after translation with google translate)

I`m using google translate to answer as follow : Tienes toda la razón.Después de un tiempo puede ser molesto.Además de que es una herramienta muy potente y te da grandes resultados 🙂✌

Yes, you got this right! Unfortunately it is not the only problem that might appear.The heat of the engine can damage the paint on the hood. Another issue is the engine sound...it`s louder in the cabin without it.

Stay tuned 😉

@@mdrc3288 22f h 22k einai

@@TheBlackTownmateXCrypton 22F = 49 cc

Hi Tony 😃 I can only totaly agree with you! Those are great high quality buggy. Thank you very much for the nice comment. Cheers ✌😉🍻

You are welcome! 🙂However do not unplug the trottle plate unless you have an alignment tool!!⚠Hope you get the dessired results 🙂😉👍

Of course,no problem!🙂I used the SILICON from BERLING which is a high quality polyurethane wood stain varnish. After it dried out i added a two substance resin called LIQUID GLASS. It is not necessary to use the exact same products.It has only to be wood stain polyurethane and liquid glass after.😉 I hope to helped you out and wish you a great result with your car 🤞😀🍀If you still have any questions feel free to ask. I will gladly answer!🙂👍

Hey, so what kind of products did you use in France, i am interested aswell. i dont want to use the wrong wood product and change it clair color. After I guess it is 2 layers of epoxy which are used ?