วีดีโอ

He’s right if you use only grease gun your bearings get no grease. Found out hard way on mine after bearing fell apart and ruined brake assembly,ruined wheel and rbrake hub as well. Had greased with gun everytime I used it

Mine is W and RC and works

From everything I've read, the torque spec on those sway bar end links is fairly low, like 18-35, sometimes (Moog) even lower at 14 ft-lbs.

Why you did not just recharge in deep cycle the thing from the beginning?

Most information I've gotten from about 12 dealer videos... THANK YOU !!!!!!!

20%man your high more like .2% it went from 12.8 to 12.2 and call it 20% holy shit! I know my numbers are not exact but yours are to the moon

Recommend this video big time, every other video shows situations that may happen, whereas thia video shows how it would ideally go from start to finish

Error on cell voltage measurement - you need to take the voltage from the first battery post to the electrolyte of your first cell and add that to the voltage you measured on your last cell. This should add up to the value of each measurement of electrolyte to electrolyte measurement you have taken. These are not actual cell voltages but they should add up to the battery voltage. Post to electrolyte voltages are half that cell voltage measure, electrolyte to electrolyte voltages are positive plate of one cell to negative plate of the other cell you measure.

What about load in between the supports......the cheap plywood they use just simply bend between supports....

Great video. How about making a video on testing Battery Desulfators? I have a Pulse Tech PowerPulse passive battery desulfator on my 2001 BMW battery and Pulse Tech claims that their desulfators and chargers use a patented frequency to extend battery life up to three times.

The battery load with the 50 watt bulb would be one half an amp not 5 amps!

I have heard that before charging, you should just make sure that the plates are covered with water, charge the battery, and then fill to full after charge with distilled water?

OMG! A YT video from six years ago helped me today! This fixed my Thomas replica radio from barely being usable to now with NO static using this method of cleaning the actuators inside the cabinet with the alcohol!!!!! Unbelievable!

Thanks! I generally do this when replacing brake pads. I also replace the sway bar bushings at the same time. Cheap and easy wear items.

I have a challenge with the audio

What if the wires are not marked? Heat wont shut off getting hotter then set

This charger has been replaced by noco genius pro50 worth $1250

Wheres the second video?

have a good weld shop make the tongue longer ,that will reduce the tongue weight .

Good job. Thank you

if car feels like its floating or wheels might fall could the sway bar be the issue?

Very informative

Greetings, during the sulfation process, do the residues fall to the bottom of the battery or simply disappear by virtue of Epson Salt dissolves? If it falls to the bottom is it important to get rid of it for the best functionality of the battery itself?

Making use of the th-cam.com/users/postUgkxcJ22tnHH9l1vjdIdEIG27iOG55P7LXI8 reconditioning plan, I just saved 2 auto batteries from being completely junked. The guides were very simple to follow. I wish I would have found this years ago! You may use the guide to recondition any battery type

do i need to jack up the car on both sides at the front, or is jacking up the car on one side (the one on which you replace the link) also ok? (i was asking myself, if there would be too much tension on the sway bar, if the car is just jacked up at one point, resulting in some kind of warping and the front axis not being symmetric causing that the link will be hard to be removed). thanks

To all:....Get a "PulseTech" Xtreame battery desulfator (s). I have several use them, on my golf cart, Miller Welder batteries and three of my vehicles. They work great. Constantly pulsing the plates keep them free of lead sulfates.

This looks more like an expensive science project. Multimeter, load tester, light bulbs, etc, etc.testing the cells wasn't show because hands were in the way. Did + & - go into cells ? Whatever. This is a film to ensure it's easier to buy a new battery. I call this film ... Rubbish & a waste of good time.

I Originally had one of these old Mercury switch thermostats. and I ran into the same problem I switched it out for a programmable one, and used it until it went wonky. and stopped turning on the furnace. I would hear the little relay inside click. and it would display "Heat On" on the display, but the furnace never came on. if I jumped the connections in the terminal strip on the back plate, the furnace would operate normally. so I bought another model of Honeywell, which luckily had the exact same back plate . so all I had to do as just snap the old one out and snap the new one in place. and it is working wonderfully again. 😀

I have an older 1970’s diesel furnace in my basement. I just followed your instructions using a Honeywell RTH2300B thermostat. (This unit is powered by two(2) AAA batteries, so it does not need a power wire. ) Your instructions worked perfectly! Thank you!!! Honeywell should hire you to write their install manual!!

It is twelve point three one volts. Saying thirty one is incorrect. Introducing such mistakes into conversation can cost property and lives.

usually i just cut these off

u da man, thanks!

This worked for Honeywell RTH8500 series on a Quadrafire pellet stove. Thank you.

Need to fix the volume.

This might be an old video but just what I needed for a 2000 outback. I noticed some of the ball joints are kept from spinning with an Allen wrench in the end (my American size fit) and some use an open end wrench ( which is much better)

This was useless. I should have watched a video of paint drying for 20 minutes

Replacing on old bi-metal (mechanical), 2-wire thermostat with a digital thermostat, I hooked up Rc & W. Works perfectly.

That banjo music is incredibly distracting.

Good video Thanks but cannot find video no 2 can you kindly send the link Cheers and thanks

Hey! You blew right over how to measure those cell voltages. How about showing us how you did it.

200lbs is the max for Subaru outback’s

Wonderful job! Thank you for sharing your knowledge and skills.

Idiots will do anything but buy a vehicle rated to tow their trailer

Wow

Cannot find the followup video

Thanks.

Can you take down that video "Best - How to fix cut Coax TV Cable Repair. Very easy damaged coax repair."? I am a cable guy and want to sh!t down your neck. The signal travels in the dielectric. That cable is no longer 75 ohms

Well for 1 this is a good battery because it has over 11.5 volts. Secondly if it was below 11.5 volts you would not bring it back to a good state unless you completely rebuild it. Your title says revive a dead battery. This is by no means a dead battery

F sa

Been looking for this info for years. thank you