- 57
- 84 549
David's IT Garage
United States
เข้าร่วมเมื่อ 29 ก.พ. 2024
Creality K1C Error Code 2564
I encountered this problem and thought I'd make a little video journal of the fixing process. I hope you enjoy.
I mention the Creality wiki in the video, here is the link:
wiki.creality.com/en/k1-flagship-series/k1-max/troubleshooting/2564-error-trouble-shooting
Chapters:
00:00 Introduction
00:22 Error Code and Behavior
00:54 Checking the Documentation
01:07 Remove Cover
01:15 Check Connections
01:28 Inspect Nozzle
01:44 Check If Temperature Sensor Is Bad.
02:00 The Problem
02:28 Remove Hot End
02:42 Install New Hot End Kit
02:55 Quick Suggestion
03:18 Test Installation
03:38 Conclusion
I mention the Creality wiki in the video, here is the link:
wiki.creality.com/en/k1-flagship-series/k1-max/troubleshooting/2564-error-trouble-shooting
Chapters:
00:00 Introduction
00:22 Error Code and Behavior
00:54 Checking the Documentation
01:07 Remove Cover
01:15 Check Connections
01:28 Inspect Nozzle
01:44 Check If Temperature Sensor Is Bad.
02:00 The Problem
02:28 Remove Hot End
02:42 Install New Hot End Kit
02:55 Quick Suggestion
03:18 Test Installation
03:38 Conclusion
มุมมอง: 652
วีดีโอ
Creality K1C - Replace Extruder Gears
มุมมอง 1.4K2 หลายเดือนก่อน
I have had to replace my plastic extruder gears a couple of times, so I thought I'd share the process. I'm also upgrading my gears to metal instead of plastic, so I'm hoping to extend their life a little bit. Chapters: 00:00 Introduction 00:49 Remove Gearbox 01:47 Disassemble Gearbox 03:55 Install New Gears 04:40 Reassemble Gearbox 05:21 Re-Install Gearbox 06:51 Did It Work?
Clogged K1C - Clicking Noise While Extruding
มุมมอง 2.6K3 หลายเดือนก่อน
When I hear this clicking sound, I know exactly what to do. It's (almost) always the same thing.
Outdoor Resin 3D Printing - Using My Creality LD-002H
มุมมอง 3464 หลายเดือนก่อน
The fumes from resin printing are brutal. I figured an easy and cheap solution would be to just print outdoors. This method definitely takes away the ability to specifically control the print environment, so it's not a professional solution. But for a hobbyist like me, it seems ok. Let me know your thoughts in the comments. URL to an article I wrote with some tips and such: www.crealitycloud.co...
Pickle Piano Using Raspberry Pi - Playing Music with Pickles!
มุมมอง 348 หลายเดือนก่อน
Pickle Piano Using Raspberry Pi - Playing Music with Pickles!
Raspberry Pi Components - How to Turn on LEDs, Use Solderless Breadboards, Resistors, Code GPIO Pins
มุมมอง 298 หลายเดือนก่อน
Raspberry Pi Components - How to Turn on LEDs, Use Solderless Breadboards, Resistors, Code GPIO Pins
Raspberry Pi DIY Plant Garden - Moisture Sensor v1.2, 5V Relay, Pump - ALL CODE ALREADY WRITTEN
มุมมอง 3368 หลายเดือนก่อน
Raspberry Pi DIY Plant Garden - Moisture Sensor v1.2, 5V Relay, Pump - ALL CODE ALREADY WRITTEN
Relaxing 3D Print - Snowflake Wand - Full-Length Print White Noise ASMR (Using Creality CR-10 SE)
มุมมอง 179 หลายเดือนก่อน
Relaxing 3D Print - Snowflake Wand - Full-Length Print White Noise ASMR (Using Creality CR-10 SE)
Creality CR 10 SE - Calibration, Setting Voltage, Changing Filament, and the Little Quirks
มุมมอง 3K9 หลายเดือนก่อน
Creality CR 10 SE - Calibration, Setting Voltage, Changing Filament, and the Little Quirks
L-Shaped Header Pins - How to Make Your Breadboards Neat, Tidy, and FLAT!
มุมมอง 769 หลายเดือนก่อน
L-Shaped Header Pins - How to Make Your Breadboards Neat, Tidy, and FLAT!
How to Set Up a Pi Zero 2 W and Zero W - Alternative to a Headless Setup
มุมมอง 4.3K10 หลายเดือนก่อน
How to Set Up a Pi Zero 2 W and Zero W - Alternative to a Headless Setup
Relaxing 3D Prints - Camera Toy - Full Print Audio and Video White Noise ASMR
มุมมอง 7510 หลายเดือนก่อน
Relaxing 3D Prints - Camera Toy - Full Print Audio and Video White Noise ASMR
Food Safe 3D Printing - Material and Settings for PETG Cookie Cutter
มุมมอง 8310 หลายเดือนก่อน
Food Safe 3D Printing - Material and Settings for PETG Cookie Cutter
Relaxing 3D Print - Fairy Atop a Mushroom - Full Print Audio and Video White Noise ASMR
มุมมอง 2710 หลายเดือนก่อน
Relaxing 3D Print - Fairy Atop a Mushroom - Full Print Audio and Video White Noise ASMR
Relaxing 3D Prints - Printer Calibration (CR-10 SE) - Sounds and Visual White Noise ASMR
มุมมอง 18810 หลายเดือนก่อน
Relaxing 3D Prints - Printer Calibration (CR-10 SE) - Sounds and Visual White Noise ASMR
Relaxing 3D Print - Fairy and Mushroom - Full Print Video and Audio White Noise ASMR
มุมมอง 2810 หลายเดือนก่อน
Relaxing 3D Print - Fairy and Mushroom - Full Print Video and Audio White Noise ASMR
Relaxing 3D Print - Rectangle Cookie Cutter - Full Print Video and Audio White Noise ASMR
มุมมอง 3710 หลายเดือนก่อน
Relaxing 3D Print - Rectangle Cookie Cutter - Full Print Video and Audio White Noise ASMR
I would exchange the screws on my extruder as well, but on my extruder the screw of the right gear was so hard to get out, that the screw broke off. Worst case, so I had to buy a new extruder. Wait to see, If on the new extruder it is the same problem.😢
Where did you buy the replacement gears?
This was what I bought: www.amazon.com/gp/product/B0D7YV1S9N/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
Thank you so much
Glad to help!
Only happened to me once, the first time I changed my filament. Now I set my temp to 130 before a retract, haven’t had a problem since.
Cool, thanks for the info!
That helped me out so much thank you
Glad to hear it!
Good lord thank you. It was driving me insane. Subbed.
Glad you got it worked out!
My K1 is giving me the error after 20-30 minutes of printing. Which is weird AF.
That is strange, let me know what you find out. Is there any buildup around the nozzle or hot end?
@@DavidsITGarage So, funny story. This problem is ONLY HAPPENING for one Board Game Insert that I'm trying to print. I've been printing for about 28h with no issues, but if I try to print the other file, I get the error. I think it has something to do with the gcode, but not sure what could cause it. I use OrcaSlicer.
@@DavidsITGarage Update: The error has returned with another gcode (not the first one I mentioned in my previous reply, but a brand new one that I just generated from Orca). I've tried twice so far, and the print stopped exactly in the same spot of the print. I think it's a software problem, but I can't diagnose it.
I think you may be right, sounds like a software problem to me. I wish you the best of luck, this sounds like doozy!
@@DavidsITGarage I managed to fix the issue by disassembling the hotend, cleaning it and applying thermal grease to the metal rod inside. I guess the old one was washed out.
Hi, some time ago I had a similar problem with my K1, I then discovered that the screws that hold the load cell sensors had loosened, everything was solved 👍. I'm happy that you solved your problem. I also follow you on the Creality Cloud channel bye👍👍😄
Awesome! Glad you gave some input here because this really is the kind of error that can have many solutions. I'm happy you solved your problem, thanks for watching! I'll be sure to follow back on CC 😄
Hello david, I am in a similar situation and I wanted to know if this method continued to work over time adn if you had any tips for it as well?
Hello, this has continued to work well for me. I meant to post a follow up but haven't gotten around to it. Right now it is winter for me, so it is too cold to be printing outdoors. I wrote some more notes on the subject on my Creality page: www.crealitycloud.com/post-detail/66e5a9818b2f34a688458715 I'll add the URL to the video description as well, thanks for watching!
Heck yeah! This solved my issue. Thank you so much!!!
Glad it helped, thanks for watching!
This thing is garbage
200$ Bambu a1 mini will be better choice
love the video. this helps me know why I needed to get a new extruder. I thought that I had personally broken or did something wrong to make it not work properly. my only question is where can I find those metal parts so I can do the same thing when my new extruder ends up having the same problem again.
Thanks, glad you like the video! I found the gears on Amazon here: www.amazon.com/gp/product/B0D7YV1S9N/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
@DavidsITGarage thank you so much. This will truly help me out. Keep up the amazing work and can't wait to see future videos.
For me, I'm getting blockages somewhere inside the metal tube. Ever time i clear it, it jams within minutes. I had printed the same file like 30x, then it just started jamming. Tried a new nozzle kit with plenty of thermal paste and still having the issue. Reached out to creality, they finally opened a ticket at 11pm on a friday, then closed the ticket around midnight due to inactivity...
That sounds frustrating. Hard to know without more information, but I would first check that filament is dry, and if extruder gears are dirty/jammed or wearing out. If the extruder gears aren't feeding properly, you can get clogging downstream.
Very nice! Received mine 3 days ago, printing daily and today changing the filament it happened with me. Thank you for the easy solution!
Glad it helped!
i love that you kept the allen key drops and little fumbles, it makes it much more relatable, who doesnt drop the things
Cool, glad someone can relate! Thanks for watching
Thank you for the video! I'm having so much troubles with this K1C extruder, that I've lost the track of how many times I had to open to unclog or to remove plastic bits of it. Please post an update after you play around with the metallic gears, this seems a better option than just replacing the extruder.
I'm glad you liked the video! I will absolutely post an update once I've tested it thoroughly. After just a day though it seems to make a difference. It has definitely fixed my extrusion line issues (although new plastic ones do that too). I ran a 14-hour print and it looks great. The filament retracts more reliably too.
What program were you in to change the printer settings? I’ve never seen that screen….
That is Creality Print, the software that is recommended the CR-10 SE instruction manual. That is actually an older version (v4), the latest version available is 5.1 which looks quite a bit different.
Quick fix and to the point.
Thanks for watching!
I hope this will work. I took this apart just 5 mins ago, but i didn't look at this specific place you show. If this only works...
Thank you! Such an easy fix for what seemed to be a bad problem!
Glad I was able to help!
Dont know why this doesnt have more views, after eatching this my printer finally runs smooth again. Thanks
Glad it was helpful!
@@DavidsITGarage Just saved my sanity. Thank you
10:17 do not strengthen too much your X axis belt, or it will rip 😅 check the nuts and bolts on your printer and put some grease on the Z axis rods
Great video. My cr10 was fine with pla plus at 220.. but with silk pla at 200 and the bed at 60 it seems to over extrude(?). Small details in the first layer distort and curl ruining the rest. Any hints please?
Silk always needs to be printed hot and slow. I would raise the extruder temp 220-230 and print no faster than 60mm/s. Let me know if that helps.
It's pronounced "to-bai-go"
hi will this work with octoprint, thanks
I haven't tried with octoprint, but let me know what you find out 🙂
im having hard time printing esun PLA+ with this CR-10 SE. Creality Print just did awful, Cura did quite okay and in Orca I didnt manage to print properly yet.
i laughed so hard
Glad you liked it 😁
Hii guys some one can help my creality printer write machine start up in progress so long time i need to make calibration
I've never heard that 1 before not sure if it's ur own original joke but it's a good 1
Spit my coffee out...thanks. 😂
Haha! Glad you liked it!
I was expecting some cool fact about how amazing your bones are. Instead, I get "you'd die without bones."
And you die when youre dead
Yes I am thanks good to know
and the crowd goes MILD 🔥🔥🔥🔥🗣️🗣️🗣️🗣️🗣️
fun fact? people drowned and you think that's fun? what's wrong with you David
Real, enjog ur heppi friday m8
Yes I will I'm going to learn something new today oh okay I guess I'll deal with that today edit good joke though
Well.. I mean he’s not wrong…
Us moment
Damn
my type of humor
Glad someone appreciates it!
@@DavidsITGaragenah now I'm laughing
Fr lol
Real 🗿
damn
damn
damn
Ow
Right?
A platypus compass?
Perry the platypus compass! That wasn't my intention, but maybe on some level that's what made me choose it.
Amazing, you can never be over prepared in a game
Two elephants were sitting on a telephone wire. Then the plumber said: This sentence is ending differently than I potato salad.
time to get a new 3d printer:)
I like the way you think!