วีดีโอ

Differently informative..thank you

Thank you!! Aha ran into some trouble changing locks today thank goodness I found this video 🙌🏾

We would like this setup in our place in Bay area. Do you work in east bay as well? Please send us your contact if you are interested in helping us.

I believe this installation and cost of the product (to be kind ) is somewhat a waste of money. In this particular application, the fan will pull air directly from the left side vent. Air always pulls from the least resistance. I doubt if little or any air will be pulled from the north end. It is the same science applied to why you don’t combine ridge vents with gable vents. Please don’t misunderstand, I think ridge vents are great when used in the proper application

Brought to you by Rupe Goldberg Plumbing.

The sad part is you had to clarify you were joking.

"Hey, Martha. I just figured out how we can fix that drain" LOL

If a non construction worker did that, I'm impressed.

Dont ever do this.

Mint

The vent under my kitchen sink just has one of those dish washer wastewater Ts horizontally behind the p trap with where the dishwasher would be facing up and a rubber hose connected to it and run down alongside the drain pipe under the trailer. It's on an island and originally it had no vent and the pipe wasnt even glued so it was dumping dishwater under the trailer. Didn't bother getting one of the fancy check valve style vents that doesn't need a pipe because it's a trailer.

True genius! Haha

Can it be used on wall tiles?

This was an incredible video!! You do a great job at capturing the experience and little stuff that needs explaining when it comes to a project like this! I am just about to use this exact product with the exact tools!

You almost had me at the end that it was code😂 😂😂😂

I feel your pain sir. Good work 👍

I once found a fernco tee buried in a backyard, the owner needed to drain his above ground pool often

Are you using the factory B&O amp or did you put a A2B interface in?

Thanks Saved my ass a couple hundred bucks just watching this I bought the replacement pet directly from manufacturer tho so it was like 118$ after tax Should last a few years …

I covered my nose and I am at home lol

When can i get some M-10 merch?

Wow , unbelievable that this isnt a toggle in the infotainment system

5:20 The rear tire is super low on air

OMG, I was laughing as watching the mods you made! When you can’t open that window it my be the first sign you screwed up big time! Good luck

What size is that fan

You need a header above the window for the stud you cut. You cut that vertical support, without any transfer to the other studs. You need one on the top, and one at the bottom to replace the action of the cut stud. Also, you did you put a header above the new entrance

You got lucky. My lightning has gotten stuck in the ajar position and will not close or open. 3 dang times. 1 time when i was on a road trip! Stuck at the dealer for 3 hours until they could take it apart and get it to close completely. 2nd time another dealer took 1.5 hrs to do the same. 3rd time i was at home and several hours later it decided to latch closed with me pushing down. I hope the dealer i take it to will properly diagnose and fix it for good.

This product needs to fully cure a minimum of 3 days, I let ours cure for 5 days, showing a bit of wear after 7 years, will use this product again. We did put a small bit of non-slip powder on the bottom of the tub in the first coat.

What was the overall cost. And is it doable understair if there is electrical there

Can this be sprayed?? Looks like it can but Im unsure.

I'm a licensed home inspector. Posting a video like this without an upfront disclaimer may not be the best idea. I would politely suggest you explain at the beginning that you are qualified to make these alterations and also explain why your method is safe. Many people will watch this video and falsely think they can cut the trusses in their home and slap a few 2x4s in their place, no big deal. NOT TRUE. I see truss alteration several times a year by average homeowners and it is NEVER done the correct way. The cost to repair it before they can sell the home is usually in the $10,000 - $20,000 range.

This is a cool project. My attic feels completely unusuable given the trus design. Im building an addition for more storage but attic will probably be my next area of investment/research.

What is that device you are using to check if the igniter is receiving power?

Thank you 🙏

I just ordered some of this, thanks.

After mixing A & B let it sit for 10 minutes, stir, let it sit an additional 10 to 15 minutes to allow A&B to fully mix.

Would that be considered an acrylic tub?

i certainly hope you got an engineer to stamp cutting all those trusses, but it's pretty damn weird that you didn't mention this or tell people that you can't simply cut trusses..... 😮

Do they make different diameter fan ... my Gable opening is on the small side.

Not on the edge😂😅living on a prayer #jovi

Dude I did this and now my Pro Power needs service. I’m kinda panicking.

Whyyy can I not get the bolts undone? What did you use? Mine might have a little more lip than yours so I can't get a tool in easily.

Very cool

this is an amazing transformation

That spider wasted no time moving into it's new bathroom.

My truck's back seat makes similar noises in any direction.

You would be better off placing it in a new purpose-built opening opposite that huge vent. That beautiful oversize vent compromises attic air passthrough by allowing bypass air in, and the large horizontal metal louvre slats and wood structures impede flow. This is effectively a sabotaged job.

Is this a mere colour restoration product or can be used in place of re-enameling also?

Does it work on all types of tubs? Ceramic, cast iron, fibreglass, acrylic etc?

Great video, thanks.