วีดีโอ

Pag naliko ako kaliwa or kanan may clunking possible maluwag lang po ba talaga?

Sir meron ako nabili na central lock with keyless pero yung for signal light niya isang wire lang. So if mag signal ako sa left sasabay din ang right. Ano gagawin ko po?

Thank you so much for the informative video,sir may i know what kind of OBD scanner you are using?tnx

more.videos

Pok pok or press? Same lang yan?

Looks to eeasy

Where is your shop contact number

Now that's a well explained example

Anong pinipihit mo diyan sa wire connector? Hahaha

Very nice 👍

Great video! Just what i was looking for. May i suggest turning your pliers the other way around to where the lower jaw is the bottom pressure application point on the nut rather than the top. For instance, when loosening (counter-clockwise) and tightening (clockwise) the lower jaw should always be leading the turn (being the shorter jaw applying pressure) and the upper jaw is always lagging the turn (being the longer jaw as the grabbing point). Just some constructive criticism - food for thought.

Ask lang po ano po bulb size ng sa reverse brake light po ng DA64W ?

what battery do you use for the fob? mine is kinda finicky when clicking it. sometimes it locks but mostly not. i noticed yiur fob led is blue but mine is red. maybe its a battery issue

For Lexus ES350 / Toyota Camry adjustment I used 44771 M16-2.00 Metric Hex Coupling Nut

Dol naa ky tutorial sa da17 keyless entry?. Saon pag top?

May naririnig po ako ganyang ingay pero pag mainit na po makina at nirerev nawawala po ano kaya ang possible na sira ?

What bar map sensor is that? My 3bar map sensor at idle only 0.5volt

Boss da63t 4x4 unit ko , tanggalin kona sana ang cv joint nya ayaw talaga makalas , pinokpok kona . Ayaw talaga

balak ko papalit hub bearing fortuner 2010 boss tanong ko lang po ano mas ok gamitin ung with abs or w/o abs?

is it possible to install keyless entry on a manual car

Back?

Ano pong sasskyan iyan?

panu ibalik yan sobrang hirap pag hnd stock mags

Thank you! Very straight to the point and helpful :)

Very useful Thanks

Ačiū

Sir. Ano po size ng bushing ? May small at big size po sa shopee kasi. Salamat

What car?

Walang check engine boss.

Sir. Same unit tayp da64w, kaso pag nka on yong aircon nagvibrate kapag mahina yong katakbo. Minsa mamatay yong kapag pag-pahon. Nalinis kuna. Kung nakapark ok nman sya.anong dapat kung gawin?

Kalo yang pin nya ada 6 bagaimana cara nya om?

What if there is water droplet at exhaust pipe also with white smoke during start of the engine? But after 30min of using the car its gone

Boss anu twag jn mag order po Sana Ako pang hi ace cumuter

sir ung sakin tumatabingi po sa ang manibela, pinatuwid qna po pero bumabalik parin tabingi. yan po ba ung inaadjust?

Hello sir. Is possible for more than a year car Toyota Vios tensioner bearing got damage. Same that sound

Hi, i have a problem that flashing air bag and horn toots when I press cruise control on, my car nissan nv200 mod 2012, thank you

Honestly good video got a cat that likes to help to. Video makes sense

HELLO I HAVE A 1998 KIA SPORTAGE AT COLD START UP THE CAR REVS TOO HIGH AT 4,000 RPMS..SOMEONE ON HERE SAID IF U DISCONNECT THE IAC VALVE HARNESS, AND IF THE RPMS CHANGE, THAT IT MEANS THE IAC VALVE IS OK?? DO U KNOW IF THAT IS TRUE> AS WHEN I DISCONNECT THE HARNESS THE RPMS DROP TO NORMAL 850 RPMS VERSES 4,000 RPMS when harness connected..please advise..thanks

Sir can you show us how to replace thermostat for da64

need to play this at 2X speed.

Salamt boss.

Boss ang fog lamp dali ra ilisan

Toyota yaris 2016 same system

Definitely a man video! No acting, telling stories of the wife going to the grocery store! Excellent video

I know this is an old video but hopefully someone will respond. I did the test just like shown and everything is correct until I test the resistance between the positive and communication lines. I am only getting .44 instead of 1.2. this is a brand new iacv so I do t think that's the problem. Would this mean that I need a new ecm?

Glad I don't need to rent a cat for this job... Excellent video! Many thanks! I believe this is causing a loud CLUMP noise when I turn my wheels to far right... It looks like two metal pieces jumping or clashing... I might be a pinion tooth sliding and jumping over the rack teeth... It would sound EXACTLY like what I am having on my Jeep Grand Cherokee 2006. Thanks a lot!

What size of 5point screw did you used?

I did not understand anything..video and subtitles very fast and step very fast..😡

No talking please

Make sure you regrease the bearing after cleaning... If not, after some time driving it, the bearing will shot