วีดีโอ

Thank you Thank you so much. I FARTED around with the seat switches for a half hour, tried to find a schematic in my manual, they don't give you one. I found your video and found out there were three more switches. The neutral safety switch was the culprit. Thank you again.

dumbest thing that BP has ever done is made all their gas handles green

There's no way that bolt gets 135 ft lbs. If I snug that bolt down too much it will stop all the modules from spinning. Have had several NH mowers like these and they were all like that. Odd.

You got me for a second I thought that was a oil filter I said that’s not good 😂😂

That filter is big as my tank😂

Yummy diesel

Help me I’m dying

Yum, water in the oil!

"Stop playing with the camera and fix the equipment I'm paying you to fix so I can get back to doing the work I am getting payed to do. " says any contractor who cares about his customers time and money. Not trying to be an a$$#@!e but that's how this whole arrangement is supposed to work.

Mmm numb numb juice😋

Turtle and rabbit lmao So technically minded this guy

Was this machine throwing a specific error code that you knew to check the dosing valve? If it was, can you share that code or codes so i can determine if my T770 has a same issue?

do you have a video of you actually taking the fuel separator off and cleaning it? I have this same issue on my M7060.

How exactly do you remove the solenoid?

GREAT VIDEO!!! Copied and pasted because this is exactly what I was thinking: Very good video. Straight to the point without taking 5 minutes to tell us why you made the video. Thank you!

Congrats!

Do i have to buy a pick up tube from bobcat or can i just keep and clean the 90° and buy a hose and clamp a screen.?? How long should the hose be or pick up tube?

Any idea what the 5 relays are inside the dash do?

Nice

Well done!!

There is the reason why I like the Krone Cutter bar....Power to each Turtle is down the rear of the cutter bar not from one turtle to the next in line, Krone has a video showing the assembly of the cutter bar........ We have 4 easy-cut 320s......

help my bx2380 seat switch is bad used jumper wire on switch by front of seat didnt work , i have to bounce hard on seat to get it to work , if my weight shifts on seat it stalls, by passed connection to seat switch and same , stalls , is there a fuse i can remove to fix it ?

my 50 hp tractor wouldnt start .....the sensor under the banana pedal was stuck ...easy fix .....just rock the pedal

Thank you!!!! Sure enough the plunger on the safety switch for my hst pedal wasn’t actuating. Cleaned it off and tractor started right up!

odd no screen on the end of pickup tube

kubota bx will not crank. will only crank and start when the mower deck is engaged. help!!!!!

Did this fix the problem though?

Nice short video, right to the point. That’s one reason why I don’t like leaving equipment sitting outside …..even tho they’re somewhat designed to do so

I thank you for this video. My Kubota L3560 had this exact problem and would not start. After clearing this nipple and bleeding the air from the system I'm back in business.

Why doesn't Kubota make the nipple a curve instead of a 90degree bend? And plumber knows the logistics behind this. P.S. I had a full size dragon fly jam up the petcock on my fuel tank a few year back on an older Ford tractor.

That’s a water separator fuel filter looks like an oil one

I needed to see the ones under the seat! 😢

What do I do if I don’t have a primer bulb

Great information. I have a B2630 and it won't start. I turn the key and I hear a buzzing sound coming from below the instrument panel. Could that be the OPC switch? Or a safety switch causing the OPC switch to buzz?

Would this issue blow the main ecu fuse?

can't hear you

Hello everybody listen to this, I just fixed my tractor because the fuel line air release valve had vibrated loose and was causing my tractor to run funny and stall and die. So finally I learned on a video on TH-cam to check that, and when I did the damn thing was half open, it was getting air. So I let it run for 30 seconds and then shut the valve. Then the tractor immediately picked up and ran perfectly. I just finished brush hogging for a 1/2 hour. And here I just changed the start solenoid. $70 on eBay. And it was not the problem, so the original solenoid is still good. Don't forget this and pass the knowledge of what I learned today. Great video by the way, thanks

Was it cranking and not starting or no crank I’m having same issue but it cranks good new battery

Thanks dude great video.

I have a kx040 2019 code 2 then 64. It fires up after about a minute dies down then codes appear again. I replaced the two fuel filters. Drained the tank put fresh diesel. Drained the air out of the system. Still the codes continue spoke to a tech he said it’s a fuel sensor, replaced that then it was a fuel rail sensor replaced that. Now they found a short in the fuel rail sensor red wire. Ran a jumper wire from the rail sensor hot wire to the EUC connector. Still the code appears 2 then 64. Rail presser high and open circuit in rail or coil? $4500 into this and still no results! I hate kubota

It would be very helpful to know how to by-pass each switch for Testing/Troubleshooting. Also be VERY helpful to "see" how to get to and replace each switch.

I had problems with my 3301 not starting. I realized that it was the PTO lever switch. Just wiggled the PTO lever a few times and it fired right up.

How do you get the fuse box cover off

I’ve had no problems, but I will check this ignition connection, I’m a big believer in dialectic grease, it will displace moisture and prevent corrosion, the key here? Ya gotta use it-Get Some boys!

Very good video. Straight to the point without taking 5 minutes to tell us why you made the video. Thank you!

Great video

I have a bx1800 and having trouble starting, it cranks over but doesn't fire I replaced feul injector and now am told it has no compression, would you have any idea what way I should go from here thanks for your reply

Another awesome video thank you thank you thank you

By any chance are you my neighbor do you live in Panama City Beach Florida Westbay to be exact

Hey thanks for the video please keep them coming could you do a video on codes whether we should run them with them flashing or get them fixed preferably codes like ….. u0083,u0082,u0081