วีดีโอ

Have used Lock n Lube fittings for years. Work great.

Where did you purchase the new wheel? Looks great!

What do you do with the factory battery terminals?

How tf yu take that 5th gear out??????

When I open my door it drops down and you have to hold it up in order to close it again. I put some washers behind the bolts of the bottom hinge and it’s served as a temporary fix for the past year but now my door creaks like a mf. I wonder if this will solve my problem.

Thanks for the great instructional videos, we need a part 3!!!

Tilt your bucket so the rain does not go in it or you can use it for the chickens the water

How much cash did this run ya?

Biden...like you have room to talk. Half vid wasted for nothing

Joe Biden? 😂

Where’s part 3??? Need help

It's a great video, it helped me a lot, where can I get the 3rd gear bronze?

Planning on rebuilding my Transmission on a 03 GT, any chance you recommend a good place to get any kits ore replacements parts for it ?

Now that I've done this a few times, I think the hardest part is messing with the stupid exhaust. I also wish my dust shield wasnt missing.

how did it turn out so far? any issues?

I agree the placement of the dip stick is not well thought out but I always remove my side panel for a little more room to check my oil.

Out of curiosity. Did y'all have and install the oil slinger that goes over the rear main. Granted Ford no longer calls it an "oil slinger". Because no oil even touches it. Unless of course the rear main does bad. I'm asking because I today I installed a new rear main on my 4.6L 2 valve. I'm just not 100% sure I've got everything fully seated. I know you can push the rear main in to far, supposedly. It's just I can no long get everything to move further into the housing, without doing some form of damage. So if y'all did not have or use the oil slinger. How far in did y'all push the main in. With the main and slinger in the housing. I might have the slinger proud towards the flex plate 0.20 or maybe 0.15. Any knowledge would be GREATLY appreciated!! 2 piece mains aside, this has got to be one of the most difficult mains I've done. Anyway, Thanks Guys!! Apologies for any typing errors, it's been a long day!!

Would a slide hammer tool work on that pilot bearing? Or would it not get behind the bearing? I have to do my rear main and I may just as well do that

great video , thanks for part numbers and the details on nuances of doing the specifics. lighting was good in some spots, other not so much :-) did u do the rear axle hydro fluid? that be nice to see. im going to buy a 1626 shuttle and this vid will help a bunch. thx for putting this together

Is this car on front and back blocks? Or just the front, would standard ramps be enough to drop the trans ?

Do you have any tricks for installing the speedo gear on the output shaft? I cracked two and I want to take a different approach.

I’m jealous at how easy you guys get the top two bolts off. I got driver side off after breaking it loose with a breaker bar. Passenger side claimed two swivel joints and continues to taunt me.

reccomend to ziptie the clutch fork down while installing it sucks for that thing to come off

decent video! thank you

Bread and you don’t have to get it wet.

How would you just swap input shaft?

Are yu still able to move the seat back n forth ?

Wow my speed sensor tone ring is VERY pressed on with my T45 (I'm swapping the digital parts onto an older T45 with the analog speed sensor). My ring looks splined... was yours smooth? If I had the cash I'd just be putting a TR3650 back in my Mustang but I think this old style T45 will last the rest of my 04 GT's life... it came with the wrong trans so I'm just fixing it up so the digital dash will work while I'm replacing throwout bearing.

Roots are a bitch no matter what the attachment

Do you need to do anything with the shifter if it is an automatic?

What color is that i want to order 1 for mine

I thinking to do the main seal in my 2001 Bullitt and change the clutch. But, do you think is worthy to do same set-up like yours even I am not looking to up more power to the car?

those look amazing! Getting the grey and black for my 06 gt.

no part 3?

How you remove the plastic after installing the seal?

very good that video is really something I had planned to do and I dare not but watching the video gives me encouragement thank you. A question. where did you buy that clamp ? is an excellent idea for those of us who don't have a press

I have a 08 mustang gt with the tr3650 manual transmission. The question is the original one that was in it it Locked up in neutral and the one I bought from a scammer.. it’s locked up in gear and can figure out why or how to fix it. Do I just need to rebuild them both or is there a reason why? Please I need your help

hey buddy thanx

Hey GTB. How high do you need to raise vehicle to get transmission out? Also did you do entire job by yourself. Great job. Thx

where can i find that steering wheel?

Any recommendations on how to remove the bottom bolt on the passenger side, (one by the oil pan) when it’s rounded off?

This is an awesome video, ya'll showed the process really well. I've never changed out all my brakes and I plan on upgrading my brakes as the next part of my 04 Mustang build.

Foreign Object Debris***

How are they for daily driving, is the lumbar good on your back. Plan on getting some next year

Biden didn’t start any of the supply chain problems. TFG stopped supplies from Mexico and Canada. We had a Global Pandemic that killed over 1 million USA citizens and TFG wanted us to drink bleach and stick lights in us. He said it would be over by Easter and churches would be full. Well we know that isn’t so. A Global Pandemic not only affects the USA but the whole world that obviously this guy below doesn’t understand. There were log jams of ships that couldn’t get anywhere. TFG also stopped trade from Mexico(remember they were suppose to build and pay for a wall? They would just swim around a wall.) and Canada so we couldn’t get items like (baby food this guy is referring too but says babby food) that we were out of. Oh and then there is TFG’s friend, Putin that has started a war that has messed us up. Biden is fighting tooth and nail to get things back under control and he so far is succeeding. And Biden HAS NOT stolen any classified documents from us.

To remove door, do you hav two remove front fender?

did you have to go with a bigger rim 18 inch ?

Great video Guys

what does Biden have to do with the supply chain issues?

Been very happy with my Ratchet Rake. Made a little bit of a mod to it. th-cam.com/video/VWABrmRPF-A/w-d-xo.html