วีดีโอ

Curious to know how long it lasted before re coating

Bro just went silent 😅

Hello Bill, one question, is what is the wind speed which you need to retract the awning?

is this 15ft or 18. i want a 15

Recently I added a bag of salt, yet the "check salt" and "Inspect Cell" lights were still on solid. What could be the problem/

Hope you’re pool is doing well

Just had se friends remove my pool however under the panels is a rubber looking thing , has a plug at the end not sure what it is and what it's for ?? Help

Yea, just squeeze the hell out of the vinyl siding

Thanks for sharing. Is there a reason you chose to apply it all by brush and not roll it on?

How did you keep from crushing the vinyl siding when installing the brackets?

Hi. I just but house. So the generator was defectiv . Work little bit. I but 1 more. Salt and cell led on solid. The salt lv 2000. The tech tell me cell needs be replac. Maybe just not enough salt? And if i will add what the proper way to do ? Pump on? Generator outo ? power AC Off? Thanks a lot

What if those two lights are blinking?

How long did this take to install?

What if you do all that and it still says check cell with a flashing light

Dude cut and roll wtf…

Thanks buddy, you’re video saved me hundreds 👍🏻👍🏻👍🏻

Great video.

Was all the prepping before the sanding absolutely necessary? Figured the sanding then go straight to staining would be enough. Just curious

nice demonstration. learbed a lot, ready to stain now. thank you

This is very tedious work. I did a 16x16 and that was enough for me. The deck looks better, but it was a PITA to pressure wash all the crap off it

Professional awning installer here. It is important to locate your brackets on studs closest to where the arms attach to the mounting bar. The arms want to twist that bar when the awning is out and mounting close the arms will prevent undue twisting. On the right side of his awning, those brackets are too far from the arm.

Would it do the same thing if the salt level is too high?

Nice video, weird some of the negative comments lmao, they got too much time. Since this video is 5 years old have you refinished the deck again since then? anything you did differently or how has the stain held up since this sanding?

Thank you, I was ready to buy a new salt cell, now I don't have to .🙂

Press the diagnostic button 5 times for a real time salt level. Also, turn off your generator for a day or two when you add salt. If you don't, you can damage the board.

My salt level is reading 0 on my generator and my check salt and inspect cell lights are on solid. I had the water tested at our local pool company and the the salt level is perfect. What could be wrong ?

Thanks, very helpful for a new pool owner.

Hello. Thank you for the video. I am wondering if you know why the SWG would be reading at 2300 if the salt level of the water when tested is actually much higher around 3200? Also, will the SWG shut off completely if the reading is too low?

No one shows the size of the brackets. My deck is just 8 feet below my roof line. Could I install this awning to my facia? That is what I am trying to find out

This is happing to my pool right now it cost me 12,000. Installed and I’ve had it only 5 years

Do i get my pool balanced before I add salt for the first time?

Another forum the guy claims the modified oil natural transparent needs to be applied with a RAG not a brush, can you provide some input? Thanks.

I read in

When it comes time to take down your current pool. You might want to take a saw to it and cut it into sections.

3 TO 5 SEC WORKED! Thank you! 👏🏻👏🏻

How do you adjust the pitch? I have 20 ft awning n the pitch is low when it’s all the way out we have to duck underneath the end

We have concrete walls …suggestions ?

My box says: SLo and the lights are on: check salt, Inspect cell and the two first light on the top are green. My water is back to green. Just getting frustrated.

My Generating light is not on. Just the power green light is on. Why is this???

I have the Tcell940 what should my setting be on my Hayward system 15,9,5,3

Skipping ahead, i was looking at the dude in the tank top and red shorts, thinking he had a prosthetic leg. Nope....its a damn sock! 😂😂😂

If i wanted to clean a deck and not remove the stain finish.. is sodium hyporchlorite (bleach) too strong? Or will it leave the stain on the wood and just remove the dirt, grime, algea, mold etc

Thanks for the video I was aware of the flashing lights for inspection but just opened my pool up here in the north east and have both lights steadily illuminated. I figured it was just my salt level being really low as it's only 2100 ppm. I had to drain the pool a few inches below return for winter and added a lot of freshwater. I was worried my cell wasn't working so I planned on adding salt soon but this video makes me feel much better. Thanks for posting, exactly what I needed to see.

What is it when my Aqua troll shows 0 salt levels and check salt and inspect cell are solid ON ?? I have salt in the pool, it's not definatelly 0..is it that the cell is out and need replacement? thanks.

Did you remove the siding to find the studs?

didn't show any of the electrical.

Is Costco the only store to buy the sun setter?

Want is the ball park price?

Mine is doing this but it does not show the salt level, when I use the test strip it says it's at 5,000, please help

great video ! gave me confidence to hit this project up ! did you have to run electric out to it for the motor ? battery operated ? appreciate the video !