วีดีโอ

Was this a front wheel drive or all-wheel drive model?

02 toyota camry le 2.4 4cylinder I just install my front bushings I had to screw the( 2) 12mm bolt at the same time so the bracket won't lift up from one side .one of my bolt seem to loose its threads it was just not grabbing had to go to junkyard got me (3) 12mm bolts for free and walla it screw right in...bushing nice n tight....start with the rear bolt first since it's tuck in in the frame you barely can get your fingers in there the struggle 😂I was to lazy to drop the frame ,start tighting the bolts evenly is gonna take a lil time ratcheting 😂. Good luck I'm a DIY😂I love this video...

the space is very tight for the rear bolt. Maybe, drop a bit the sub-frame? Need big big wrenches, but not a biggy if you have such.

Thanks. The video helped but my license plate bracket was hard to get off. I had to yank it out. After I removed the 2 bolts it had about 4 snap on connectors. I had to pull hard and some of them broke off. But it didn’t affect the re-assembly and it went on pretty tight with the screws and license plate screws. Also, it had a rubber seal around it that was a pain to stay on as I placed it back into the car. I appreciate your help. The wire colors were accurate for my 2006 Nissan Altima with an Alpine ilx-W650 which has the Apple Play and now has a rear camera!!!

شكرا..شرح بسيط ومفهوم

Thank you for the video!

Wow dude your video is really good , thanks a lot for teach us ... have a good one

Best video I've seen. Now to go get it done myself 😤

Would like some commentary as to what you are doing. also did you burp? gross

👍

Thank you

😊awsome video.man....nice n slow...

Bought used civic over 200k miles the fluid drained and has same color as yours , 4 drain and fill solved it .

Great clear video but at least put some brake grease on the abutments areas and grease on slide pins or at least spray some silicone in between the slide pins... Everything else good.

...uhmmm... This video is very complicated . I think he'schanging the struts . There's another video ; very easy to do that ./.

what was the ohms for the bad egr? what where the ohms if egr was good?

How much

Thank you for the videos it helps a ton with this stuff

Good video thanks for your skills to teach us men right 👍

Thank you so much for this video! I'm installing a back up camera on my Altima today so i really appreciate the descriptions of what wires to tap into

Belt nambar

Great video, straight to the point

Can’t understand what he is talking about

Does atf level is in HOT during engine running?

Always change the hardware, but don’t resurface the rotors? 😂

Thank you so much.

Kuya, what brand of oil filter did you use?

The mistake of everybody at 5:45. Do not lubricate, must be dry like a bone. It will squeak.

Lubricate guide pins with what exactly? Thanks.

What size is the exhaust flange gasket that goes between the down pipe and catalytic pipe by the 02 sensor? I bought a genuine Toyota one but it's to big. I got a aftermarket walker exhaust too.

Excellent demo. Thanks!

Hey, I have a question, I went to auto zone yesterday and purchased a transmission fluid for my vehicle, I didn’t know you have to drain the previous fluid, well of course they do that for oil changes, I assumed I would just be able to put the transmission fluid into the correct place as shown in the video. The transmission fluid and oil are two different things

Nice one mate. Thanks

You forgot to put the brake grease on the shims on the brake pads

Hi, I was wondering if the front suspension system also has struts or does it have a shock absorbers? Thanks

This is very helpful 😂❤❤

Just so you know, I had a 96 Camry V6 exactly similar and you do not have to remove the entire strut assembly just the two large bolts and it will swing out of the way, but he did a good job but you need to pack the ball bearing end with a lot of grease before you reassemble

My favorite part is when you drop the sockets and ratchets. :D Just like in my garage.

Nice

Glad to see someone cleaning up the hub and bolts before putting on the new parts.

Thank you sir

Ill be paying for a experienced technician...

Thanks brother... got confused when I saw just the filter (no hardcase) and oring in the box for the first time on this car but it's still a basic oil change! keep on keepin on!

Only one of the pad get the wear indicator clip?

Good video but it would've been helpful to add the torque specs for each bolt or nut.

Important to tighten the final Hub nut to factory specs!

I thought you didn’t need the cailper tool to put em back. I heard that there’s a button that pushes them back 😊

dont you need a caliper tool for newer gm to push the piston in and also be able to twist

@filpinoymechanic148 (google translate) El amortiguador debe bombearse antes de su instalación, debe comprimirse lentamente varias veces para que comience a funcionar correctamente. El amortiguador no se puede instalar de esta manera.

This helped a lot !!! Thanks