วีดีโอ

Thanks for the suggestion. Worked great in the snow

What didn’t you like about the truxedo pro15?

I bought this one as well after seeing your videos. Hope it holds up better than my soft cover did! lol.

How long does it take to remove entirely or can you still put a 4dt wide sheet in it with the rail on.

A little late to the party, but awesome video! The algorithm did its thing well today. I had been looking at getting one that is exactly like this one for $350. I hated Ford's version so much. Turns out Amazon had it for $140! Placing my order now!

Looks great! I went with the Rough Country tri fold for $750. Nice to see some options for these trucks.

Any updates from the last two months?

RTFM

Change your job! 🤌🏼👎🏻

The noise is the high pressure pump

Master vinyl wrapper here. You didn't apply the heat soon enough and that's why you have creases. As soon as you laid on the vinyl overlap you should have applied heat instead of trying to work it without it that's what caused your problems.

You should probably roll it up so we can see what that looks like.

You're a life saver!

Great design which could fit 2 dirt bikes as opposed to the Ford “V”design

Just watched your video an will install my catch can today on my Maverick

Nice man that looks tight!

Is that a blackout edition?

Where did you get the vinyl logo from? Thank you.

what means " cancer " on the back of oven ?

21 mins just to install tiny little stickers 😅

How watertight has the TLAPS been? It looks like water would pool on the cover and seep into the bed.

the fan is noissy i have this oven

Hey! I’m Kathy from Mabett, and I’ve been following your channel-love your passion for the Maverick! I’d love to explore some collaboration opportunities with you to create exciting content for fellow Maverick fans. Let me know if you’re interested; thanks so much for considering it!

the fan is noissy?

Very cool do you think you get a full 2 feet more?

Read the reviews, both web sites do not go to the product. One goes to a company that has many orders unsent and no refunds. Scammers apparently.

How do the sides latch down? Is it just velcro and are you able to pull it up from the sides? How water resistant is it?

How much for the soft one?

It's held down with Hook and Loop (I highly doubt it's VELCRO®). HARD pass. Just let the thieves right in. You're comparing Mac PowerBook Pros to Best Buy's cheapest laptop of the week. It's an invalid comparison.

Squeegee, warm that up before to stick and work in a circular way from the center

How well is this holding up after 2 years?

Curious how this emblem holds up to car washes

So I just saw a test of a European version this oven done by a German guy. So he used the automatic napolitan settings, 400C top and bottom 2 minutes, and the result was pretty perfect. I've seen other testers going free style (manual setting) and they have identical problems as you guys. Maybe you should give the auto settings a try :)

Would you prefer this or the ford official one if they are the same price?

I been using chefman oven for awhile. New York pizza is dead on ,but far as making Neopolian Pizza its just alright. You get what you pay for. Thats why i decided to get the Ooni electric oven. Price is steep ,but so far its the best indoor electric oven out there.

Lots of poor info out there, here's a good example, yes a catch can is essential for Ford Ecoboost engines to help them run for long miles without clogging the intake valves, this issue is due to the use of the turbocharger boosting the intake pressure hence increasing horsepower from the engine and increasing piston blowby, along with the change from port fuel injection that would clean the intake valves to direct injection. Problem is, there is no way for any of us average folks to know whether these catch cans actually work unless we were willing to remove the intake manifold after many miles and actually look to see if the intake valves are getting clogged. Barring that, the best we can do is the best possible job with a catch can, and that means installing one on the high side (PVC side down on the front side of the block) and yes you can also put one on the low side as shown here (top valve cover hose) as an added plus, but the PCV side is a must for a catch can. Other youtube videos go over this type of install, not really hard to do at all. And most importantly, the air returning to the engine must be filtered and these cheap catch cans from amazon have no such filter. If you're going to bother to install a catch can, skip the cheap Evil Energy junk, and instead be sure to use one with a decent quality brass return filter such as found on the Mishimoto universal catch can, yes it costs over $100 just for the can and two connectors, but it is high quality and has a very good brass return filter, spend a bit more money now, save thousands later, simple. And BTW, the PCV hose connectors you will need in order to do the install on the PCV side are readily available from UPR Products for just $10-$11 each (I looked everywhere for these, finally found them). My total cost for parts was $115 for the can, $25 for 8' of good quality hose from Autozone (cheap hose will collapse when put under vacuum), $10 for hardware and clamps, and $25 for the connectors with shipping, total cost $175, very high quality install that can be trusted and relied upon, and far less than some of the other kits out there. UPR has a full kit for the high (PCV) side for $150 with all the connectors, also a full kit for the low side as well, same price, but not sure if those utilize a return filter in the can such as found on the Mishimoto can.

You cooked most of them whilst the oven was pre heating and not up to temp! Apart from that it was a great trouble shooting video

I’ve already added catch cans to mine and your clean side video was helpful, but I gotta say great job getting the camera under there! Now I know what I’ve been feeling around looks like. 😂 That’s also a great place to connect a hose for induction service. Just get another quick disconnect and a long hose and you can do it without having someone else hold the RPMs at 2000.

Use the Manual!!!

I did this on the front and back of my Maverick and I didn’t have that many problems. I didn’t use any heat either.

Afternoon nice job it looks amazing my Explorer is the same color. What color is that vinyl? Is that matte black or gray I’ll like the same color.

Awsome! Came out really good!

Not available anymore? Can you post the stl file somewhere if you're not gonna monetize it any more?

Hey Matthew, Happy Saturday. I have a question regarding your Cubby Grid? Are you still selling it in black? I can't seem to find it on Etsy anymore. Thanks.

What if you cook the dough for a few minutes, before adding the toppings?

Another clear and concise video!

Can you turn in lane centering without cruise control on?

Looks great, good job. How is the UV light on it? Is it discolored?

This is sick, thanks dude!

Pathetic 😂