วีดีโอ

سلام من در خدمتم ، بفرستید با هم چک میکنیم تلگرام هم میتونید پیام بدید @mani_fa

@@manifa59 خیلی لطف می کنید. من ایمیل کردم براتون

اوکی

Hi The title of the video shows that this video is about wifi control of your Mach3 , and this is a trigger to show friends that it is a way to control Mach3 over wifi via Android phone. For Handweel you can see this video: th-cam.com/video/dtTE6CQRhdc/w-d-xo.htmlsi=9mX63zmWAycAKA7g About requirements suggestion, Good Idea, Thanks 👍 And for any problem up to solve it , you can be in touch in telegram: @mani_fa

Hi Machrodant Server file uploaded in description (in related video) Comments of Machrodant video are ON now👍

Hi , full video coming soon in 1 or 2 days.

@@manifa59 tnx a lot, I like your videos

@@3dmodelinghamid238 Glad to hear it.❤

Hi glad to hear it. Connector name: IDC 10 pin connector www.amazon.com/Aexit-10-draads-IDC-connector-moederbord-lintkabel/dp/B07B7FWYRM

Hi Glad to hear it

you're welcome, glad to hear it. 🙏

Hi No need for a PCB , just some wiring that I have shown in previous video maybe I should design one, Good idea, Thanks 👍

Your welcome 🙏🙏

Hi yes , I made a board with STM32 and it works great. here is the link: th-cam.com/video/VSfFu88z7-w/w-d-xo.html

@@manifa59 sori i meant GRBLHAL

I did not test GRBLHall yet Maybe later to find a good PCB to make and also test it in many ways.

@@manifa59 thank you, I am very interested if you make a GRblhal based stm32 PCB with optocoupler protection

Hi Let me try I guess you can use them , but I do not recommnd to use them for any uses like limit switch , these pins are not isolated with opto and have 5v voltage level to operate.

Hi Great

So glad to hear that

Hello Does it have any manual that I can look at?

Hi If you mean how I power the CNC shield through Arduino , I just solder VIN pin of CNC shield to positive terminal of Shield and now I can power both from power of Arduino.

@@manifa59 just positive pin or negative as well? I want do this because HC05 only works by powering the Arduino, both with 12V in this case. Thanks for answering me.

Yes just positive pin. negative comes from pin headers and no need for wiring.

@@manifa59 In my case I already have a P4 on the CNC Shield V3, if I solder it this way it will power the Arduino in the same way, right? I'm powering a 12V fan and the Shield V3, in which case will I power the Arduino too?

Plug P4 is soldered with a wire and is on back case, then I feed it through the Shield V3, I will solder a wire to Arduino and test it.

Hi you can download firmware from the link below: github.com/makerbase-mks/MKS-DLC32/tree/main/MKS-DLC32-main/firmware

سلام نسخه برنامه R3.043.066 هستش و لایسنس هم لایسنسی که همه استفاده میکنن

Hi off switch? you mean the side key? In some models the side key works as an on and off switch and some others use like my model. even after releasing the side key , the previous axis must be selected.

@@manifa59 My mpg is for the model without the side key. What I'm talking about is a rotary switch that selects the X, Y, and Z axes. Even if you leave this switch in the off position, the x-axis is still selected. I asked because I wasn't sure if I should use it in this state or if I had done something wrong with the settings.

You're welcome my friend I haven't tested it yet for vetric yet.

@@manifa59 No problem, you strike me as a bit of a coder so if anyone can figure it out that also uses it I'm guessing it would be you more than me. I am absolutely not a coder. But I've downloaded the vetric gadget maker files to use the add ons, some are better than others and I did find one spirograph gadget but not as cool as some of your finds.

Hi Blue and Blue/Black used for emergency stops and you can connect them to IN1 UpTo 4 , one lead goes to DCM and another lead goes to Input I didn't understand what you mean exactly

I thought the inputs and outputs on that board get wired to a 24v supply

@@johnalex3023 Aha I get it now. for these 8 pins they are not. they work with 5V instead of 24V and GND instead of DCM. remember, IN1-4 and OUT1-4 are opto isolated , therefore they can use 24v to operate.

If I wire that estop that way, can I still use 24v on the other I/O?

@@johnalex3023 Yes , for sure estop did not connect to those 8 pins and it is a separate key. for I/O 1-4 you can use 24v like before

Hi you can use these pins for axis movement but not with this video configs , wait for the next video about jogging .

@@manifa59 okk

Thanks. In the manual, it mentioned that these pins can be used just for general inputs like buttons and also not suitable for limits. but if you want to use it for other purposes, let me know And I can test it for you.

@@manifa59 thanks for answer, it was all I needed to know

Is tis work x,y,z movements.

سلام تنها قسمتی که فقط با یه تیک زدن باید کار کنه ، انکودر هستش که توی نکات گفته شده چند حالت داره : ۱. انکودر ۵ ولتی باید باشه نه ۱۲ ولتی ۲.امکان داره برد هم مشکل داشته باشه ۳. امکان داره سیم بندی انکودر متفاوت باشه برای تست انکودر بعد از تنظیم وارد تنظیمات افزونه rnrmotion بشید ، با چرخوندن انکودر باید قسمت A و B تیک دار بشه و بازی کنه حالت دوم تست هم با یه ماژول انکودر ساده آردوینو هستش که در حد تست میشه متوجه شد که بخش انکودر کار میکنه یا نه

آخه تازه انکودر رو عوض کردم ممکنه مشکل از brain باشه

انکودرتون ۵ ولته؟ نه کاری با brain نداریم ، اگر احتمال میدی خراب باشه ، مچ تری رو دوباره نصب کن خودم با اولین تنظیم به راحتی عملکرد انکودر رو دیدم و بعد رفتم سراغ بقیه تنظیمات (دقیقه ۱۳:۵۱) تنظیم خاصی نداره برای اینکه کار کنه ، ولی دیده ام که برد مچ تری قسمت هندویلش مشکل داشته باشه اگه برد دیگه ای هم دارید تست بگیرید دوباره باید بگم که با ماژول انکودر آردوینو تست هم گرفتم (فقط با تنظیمی که گفتم) و کار کرد

اتفاقا دوباره نصب هم کردم مچتری رو فقط مونده برد که یه دونه دیگه بندازم بازم ممنون از لطفتون بله انکودرم ۵ ولتیه

سلام مهندس جسا رتا سیستم عاملتون چیه و چند بیتی است

Hi my friend Thanks A lot 🙏 To convert SVG to Gcode , you can simply use LaserGRBL software ,Also BachinDraw , LightBurn softwares can do it too

ok thanks keep it up

Hello If MPG A and MPG B ticks and while rotating they must change, for the test I use a rotary encoder module (for arduino) and it works somehow ok 1. The encoder must be 5v 2. If all settings are ok , check with another BOB let me know the result

"Death to Sharpie" Processing software source

Hi They can be use just for general inputs as a key or push button, so you can use them for for e-stop or run, pause , stop and so on , but not for endstops next video will be about these compabilities about adding more 8 push button.

@@manifa59 Nice to hear that! i let an Abo there so i dont miss that !

Hi where is your problem exactly? @mani_fa (my telegram ID)

@@manifa59 Can I contact you via email? Because my telegram is not working

Spindles will be on and off with gcode and configuration in output pins , I have a video to show you how to run spindle , wait for it ...

Hi I do not have it now but a schematic of wiring can be found here: cncyadak.com/wp-content/uploads/2020/09/Handwheel-MPG-CNC-MACH3-Siemens-GSK-4.jpg for any problem comment here

Config and wiring Video is about to finish.

As I know if your velocity and acceleration is so high , your motor movement does not work well, change these values , and you can use other values for x10 and x100 too

​@@manifa59but when I drive on my keyboard, motors go well (also when I use Shift - full Speed). IT is something like software don't akcept highest value of motors speeds.

...for specifycation i have handwheel without side button

@@petrkriza3654 So let me check it

OKAY Let me make it ready

@@manifa59Thanks. I’m waiting for your return

Thanks to you, I found a method.

Your welcome man ,glad to hear it

Hi Base on documents of this board (v2.1) , it can operate upto 10w laser module and max 3A to 5A , 80W laser in max power uses 3.5A so it can be used in this board. If you have any doubt and if you want work safety , you can use separate power for laser like this: drive.google.com/file/d/12-9RIztQOyfhhU09ASBLlqhq8ZfQfxeT/view?usp=sharing with this schematic you can use any laser module with any power 😉

video will be release tonoght.

So Glad to hear that ♥️

Hi TNX a lot. I convert images to Lineart. What do you mean by converting a text file to an image? If you have a text and you want to convert it to this LineArt mode , you Can save the text file as an image and do the conversion. If you mean anything else , please light me up😊

@@manifa59 All I can say is that it's text art or ASCII art. So for example: ,,,,,,,,,,,,,,,,,,,,,,,,$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$ ,,,,,,,,,,,$$$$$$$$$$$$$$$$$ ,,,,,,,$$$$$$$$$$$$$$$$$$$$$$ ,,,,,$$$$$$$,,,,,$$$$,,,,$$$$$$$$ ,,,$$$$$$,,,,,,,,,$$$$,,,,,,,,$$$$$$$ ,,$$$$$$,,,,,,,,,,$$$$,,,,,,,,,,$$$$$$ ,,$$$$$$,,,,,,,,,,$$$$ ,,$$$$$$,,,,,,,,,,$$$$ ,,,$$$$$$,,,,,,,,,$$$$ ,,,,$$$$$$$$,,,,$$$$ ,,,,,,$$$$$$$$$$$$$$$ ,,,,,,,,,,$$$$$$$$$$$$$$$$$ ,,,,,,,,,,,,,,,,,$$$$$$$$$$$$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$,,$$$$$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$,,,,,,,$$$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$,,,,,,,,,,$$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$,,,,,,,,,,,$$$$$ $$$$$$$,,,,,,,,,,$$$$,,,,,,,,,,,,$$$$$ ,$$$$$$,,,,,,,,,,,$$$$,,,,,,,,,,,,$$$$$ ,,$$$$$$$,,,,,,,,$$$$,,,,,,,,,,,$$$$$ ,,,$$$$$$$$,,,,,$$$$,,,,,,,,,,$$$$$ ,,,,,,$$$$$$$$$$$$$$$$$$$$$$ ,,,,,,,,,,$$$$$$$$$$$$$$$$$$$ ,,,,,,,,,,,,,,,,,,$$$$$$$$$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$ ,,,,,,,,,,,,,,,,,,,,,,,,$$$$ What I am asking is if there was a tool I could use to easily convert/space a paragraph of text/words into the image.

Hi Ok , soon . and by the way the board is self designed , I put the link in next video