วีดีโอ

I don’t think the trigger bar comes out that easily.

I’m sorry, at 6:01 you said the trigger bar tab needs to go _under_ the connector, but I believe it should go on top of the connector, correct?

You did not adjust the pre-travel set screw.

Hi what parts do i need to buy and from where? Thank you in advance:)

Painful to watch. First obvious problem, a 16oz claw hammer is not an appropriate tool. Second, when he drives out the pin and the punch sticks in the frame he's damaging the frame hole. Third, and probably most critical, never reuse a roll pin, especially on a CZ where they are notoriously soft and often in need of replacement just from average use. Further hint: Mcarbo makes a tool for replacing the spring easily. I also recommend their replacement pins both for trigger and hammer.

Make a small pin ??

Nice video. Pressing the cylinder release button and opening the cylinder slightly will help the trigger group pop into place.

The only thing I would add is clean the slider pins while the carrier is off.😊

Thanks for the video, great help in getting my mower deck back on correctly.

Best video on spring replacement I have seen. Plane and simple. Thanks!

Great video, very helpful. You've given me confidence to try this myself with my new cz75sp01

What barrel is that?

Importaint to know, when changing hammer you might need to change sear aswell, or adjust the old sear or the safety wont work. You also risk having a hammer that is not safe - pushing it might cause it to drop and fire.

Great video

My 10mm nuts are so tight the whole thing is moving

Them pads what that bit of metal on the pad stick out which goes in inner side what it for ?

I have an older first generation GP100 from the '80's. There is a solid cylinder-shaped guide pin that goes into the hole at the bottom of the grip frame. It keeps the two-piece grips aligned and snug together. I don't see it in yours.

Followed thru for replacing my GP100 springs in 44 spec. Well done! Thank you.

Great video. Thanks.

I would also like to add that the small connector for the lock and license plate light, behind the chrome strip, can corrode and lose contact, so the bulbs do not light or the trunk does not always open. That was my problem.

THANK YOU BRO!!

Fantastic video! Thanks very much.

Can anyone tell me if this video will apply to changing the trigger on the CZ PCR as well?

I tried to do this on my car but some muppet had mangled the carrier bolts so i couldnt undo them even with the proper socket, my discs weren't too bad anyway so i just changed the pads, if i do decide to change the discs ill just ask a garage to change the bolts for me !!!

Maybe you should've rehearsed this a few times before making this video.

thank you

Now I can tackle my GP-100 and install the Wolff springs.

Great video. This is my first revolver. How often do you taken down the revolver after shooting? How many rounds?

Claw hammer FTW! I love it... im getting ready to do mine, but my trigger pin looks like its been swaged out on both ends to keep it from working its way out.

Thanks 👌🏻

7

Wow I bet it’s hard to get parts much less own a pistol across the pond.

Should the parking brake be left on?

I prefer the factory springs for enhanced reliability. Plus over time the springs will lighten up on their own if you shoot a lot

Thanks for the video! Wondering if you could give me details on what memory sticks that I would need to get for 2x32 64GB. Thank you in advance!

I just put it on mine. Thanks so much for the video helped me a lot 🙏🏽

Thank you for your excellent video!!!! It was amazing how it works again. Everytihng is very , very, very well explained. 😀😀

Done one side and the disc is difficult to spin it's up against the nearside pad will it free up in use?

hola,tengo se podría decir mismo modelo, como puedo sacar el tambor gracias

I recommend never use a hammer to install the pins will bend if hit wrong only use punch MY OPINION

I never took the spring that holds the center pin in I only took spring for trigger reset off! I had to file several thousands of a inch off my reset bar tab!

I installed the GHOST ROCKET TRIGGER RESET BAR and its really 3.5 lbs trigger!

very very helpful!!

Just use a hammer to get the old disc off

Excellent guide!!! Tack!

When it rains I get water in my trunk from the tailgate handle but I can't find where the water comes in when I remove it😢

Merulafilms, I am going to replace the trigger in my SP01 with an Armory Craft flat face trigger. So just to be clear, I don't have to do anything else to my weapon except the trigger change like in your video. Thanks and great video, clear and concise. Be well.

Will this work for the decocker models?

You use Cessna ?

Mine isn't coming out its like stuck inthere