วีดีโอ

Actually it is a Hultafors Re-Brand. And they came out with a new model for 2025. Hltafors-H0619-claw-hammer-tr-el

Is the turbo 2000lm for 2 hours accurate... or does it shut down after a few minutes but can do this for 2 hours?

would you say its good for building a pc?

I build 1/8th scale railcars and locomotives as a hobby so I drill a lot of holes of varying sizes. I am not a metallurgist but I wonder if the fragile nature has more to do with the percentage of cobalt than the drill itself. I have a set of Stroton 6% cobalt SAE drill bits that I have been very impressed with. Like you, I always use a cutting fluid (I use Tap Magic) with every cut to preserve the bit and cutting surface and I do not put excessive pressure on the bits or very high speeds. I have broken a couple of the bits but that was mostly my fault for various reasons. What I've found is that if you contact Stroton, they will replace the bit for you even if it is your fault.... or at least they have for me on two occasions. Now, I am not drilling into stainless steel, 90% of the drilling that I do is into mild steel that is 16 gauge up to 3/8" steel plate and 4" steel I-beams and C-channel which does make a difference but I have had great results.

After a few years of using the 816 it got stolen, so I wanted to see if I should buy the new version or get the 816 again. One thing I liked about the 816 is the mass and size, as it allowed me to twist my wrist and let it free spin while I'm lightly holding the rapidapter. Very nice for my job, one spin and I thread almost any screw completely, then do the last twist to tighten it (works for unscrewing too). I assume with the new version I can't do that, but I feel like it's cool enough to be worth a try.

Be cool to see a drone w a couple high power lights on a night mission low to the ground.

Fully off topic. Maybe you would know the answer to a question since you are so knowledgeable about lights. I own a Nitecore SRT7i. With the multi mode selector interface on the tail cap. 5 modes. Do you think if I took this cap off and put it on the P20ix it would also work? Same iseries battery. That way I’d have a thrower and a flood with identical interfaces.

How does it compare to the Sofirn HS21?

Really good video, interesting, a one of Edinburgh would be great overlooking the castle.

Close ups, soft voice... If tool pr0n existed, this would be it! 👌😂

You shouldn’t call it Castle Douglas as that is a town in Dumfries and Galloway. Where you are visiting is Douglas, where you can visit Douglas Castle.

Great clear video from wee Stallone the Drone and lovely views. I enjoyed seeing a birds eye view of Northumberland and Tyneside

Oh for goodness sake. I was expecting a review of the 33. It just drones on about other lamps …….

Awesome video Richy mate. Love it and may 2025 bring continued good health, peace and happiness. Cheers.

Compared to the HS21?

Absolutely fabulous...well done Richy ♥️⭐

Love the drone work! Hope life is good and 2025 brings you health and happiness. 🙏 Much love brother.

Beautiful , stunning , great video , love it.

No snow? We had loads in Harrogate, then a week of hard frost, it's just starting to slowly thaw now. Great video quality from the drone!

Nice work!

I also got the tiki because of price (more than 50% more economical). Yes, highest output is also almost 50% lower but for being a keychain flashlight I really do not need the extra lumens. Also, once the battery finally dies, it is less painful to throw away. All in all, I am very happy with the tiki.

Thanks for the video 😊

I have a couple of std. VC8 and they are good for medium sized cells. IMHO they should add som options for even lower charging levels. 😏 I use a lot of AAA NiMh cells and CR2/CR123 for various IOT sensors. Small cells ( 650mAh - 1000mAh ) will have better endurance if charged with 100mA or less. 👍 That said - the VC8S will be great for 18650/21700 and I will definitely buy one. 😊

What a superb review! Very helpful to me in making my decision on what to buy, you certainly covered all the essential points! Thanks and Happy New 2025!

Go carefully my very good friend ran into 3 creatures in that forest he described them as human gorilla's

Is it sft40 ?

Good

Nice to see through a lens that doesn't bend the trees as you go by them. It IS possible. Stay well.

My Dad was born in Berwick 1920, after WW2 went lived Toronto Canada, I have always wondered about Berwick, havent seen any residential homes in any videos about Berwick, I wonder where his family would have lived.

I just received mine, caught me by surprise but if u pull it hard, the front part come out, and its essentially a bit holder snugly fitted into a handle. Weird enought the bit holder has a 9mm anvil. Could you help to verify my finding? I cant seems to find any info regarding this.

I'm leaning more and more to "i want it"... The Perun 2 is worthless if its raining or snowing, the proximity sensor will dim all the time. And you can't shut it off.

Hi there, another channel that reviewed this model said that it started to step down from turbo at 30 seconds. Did you get the same result? Can you explain a bit about any stepdown from turbo that you noticed please?

My used Knipex tool.

Hello! Educational video, in the end your verdict, is it worth taking this flashlight or not? Thank you!

$22.99 from Amazon on December 3rd. 2024. Currently (12/5/24) it's $29.99 -20% or $23.99.

Вы знаете, что у этой отвертки съёмный битодержатель?

PBSwiss ❤️

Please try double ended bits and Leatherman flat bits with different locking mechanism.

As the packaging implies (first dipiction written in German) this product isn't made specifically for the US market. I guess this is the reason for the PH1 issue, as in Europe the PZ is probably the most used bit in DIY.

Is it made for US or Japanese bits?

Lovely video on the juxtaposition of different screwdriver handles with vessel. However, the long locking head on the vessel is also designed to accommodate double-headed bits, which you mentioned in the beginning but perhaps remiss to demonstrated later.

??WAIT.... something from the holy vessel thats NOT perfect and worth the outrageous price?! ... dont let the other shills know! ... smFh

The Vessel Megadora handles are my favorite, so I'm definitely interested in that. I've been very satisfied with all my Vessel purchases so far. It's awesome that it works with standard and Japanese 1/4 bits. I just started buying Vessel bits anyway, and they're every bit as good as my Wiha bits. Maybe even a little better. Time to hit up Amazon again.

British countryside is so boring.