วีดีโอ

Excellent video. Very well explained. Thanks

That door is sprung too much, it shouldn't go all the way up by itself that easily once you release the catch. That could be what lead to your previous unit giving problems...having to fight that much force to get the door down.

Wow this was very productive video and well put together. 🎉

Very helpful

Fucking click bait.... the lay of the sealer which he is clearly looking to getting endorsed for is shotty work tbh. Practice more then post some fake how to videos

Very good. Don explains this fully and has shown that if you mess up, it's fixable. Thank you, Don

This video is great! Much better than the other guy that didn't show all of the steps.

Buddy. This video is exactly what I needed to confirm my installation. Thank you. God bless you.

This was by far one of the best instructional 📹. Thank you phenomenal job!

Thanks....this was very helpful 🙏🏾

Pretty sure the garage door springs are wound too tight. This may be why the old garage door opener failed. The door should not spring open by itself once the door opener lever is disengaged. There are of course a ton of videos on how to adjust garage door springs but the general rule of thumb is the door should stay open by itself once the door is half way opened manually.

Very thorough guide that considers the little things.

I still can’t get the pull to open the garage door

So what is the mistake we are to avoid? Clicking on click bait?

Ñ Ñ Ññ Ñ Ñ Mm Ñ

So how do you release them when they are actually under tension?

Outstanding. Thanks

How often do you recharge the collar?

By far the best i love you man i was so stressed out over this and i was watching this when i left home i came home so excited cause with your help i figured out what i needed to do and boom it worked and now its all set and the kids can get in and out safely

Cool. I'm checking out their electrician bits. How are they holding up?

Do you have to sand before sealing

Excellent install instructions

Harris Maria Lee Frank Jackson Sharon

Ready to tackle this tomorrow. Thank you for the great explanation of it all.!

Great detailed explanation

Rodriguez Amy Rodriguez Richard Johnson Jeffrey

Great detailed video! Bravo 👏🏽👏🏽👏🏽

Great video-I have the same one.Well done man👏👏👏👏

Even with all the instructions this install is a pain in the a$$ if you can afford it pay the $200 install fee and save yourself 4-5hrs of work

Need help. One sensor has a red light and the other a green light. Is it normal? The - is the up and the + is the down limit. What did I do wrong?

Best install video of this brand I have seen. Without it I wouldn't know about the programing!

Thx so much, simple but necessary.

You can also use a speed clamp on the level to hold it in place

Well done video 👍

👍👍

I just completed an install on a similar Genie. The sensor wire routing forced me to do a modification. I didn't want to route it out and around as my garage has a finished ceiling. You can't just attach it to the rail (my old one you could). As the rail is hollow, I drilled a hole on the under side about an inch from the motor head. There is a Bolt hole towards the end, must be for over travel but I removed it. I used Fish tape to get the wire in the rail and out the removed bolt hole. You only need the one wire as you can wire in a series. Made it so much cleaner.

A tip for installing power head. Make sure the carriage is disengaged , open the door by hand. Use a block on the door to support opener rail . Check rail if it is level, adjust if necessary. Now mount power head at same position. Remove support block from door flip carriage to lock position, move door by hand to lock into carriage. Great video enjoyed it

Great video, down to the point. This is the sealant I'm using on my shed. Looks like the perfect color too. Thanks for taking the time to make this video. Peace brother.

You're going way too fast - it makes it heat up and work way worse.

You didn't show how the plastic carrier that the door hooks to is moved by the turn buckles or belt

Man, you should do more videos, you are great in explaining how to do it! Congrats on the video, I will install 2 this weekend and will use your video to get it done!

pretty much as expected. A little better than nothing.

Great installation video, very helpful. Thanks

Thank you

thanks for the video,. I'm going to install my Genie door opener today.

I'm with you, brother. Those yellow old school straps suck! They are such a PITA to use, and the excess strap has to be secured so that it doesn't flap in the wind.

Thank you for the review I really appreciate it

How much you charge for the installation/repairs??

Great review love the humor 😅

How did you attach the pad to your drill? I have the same drill and the pad doesn't spin when i apply it to the car.