วีดีโอ

All that work for barely any performance gain 😂

i drive a RAM Rebel 2019 and just came across this page. Def subscribed.

Fix worked great only issue I had was getting the ball joint piece out so I took of the rest of the mount on the engine and then took a grinder to the knob instead of removing the whole piece

I believe a heat gun would get rid of the white bend in the plastic, I wouldn’t suggest just going right in thought test a piece first and see how it goes

It's a lot easier to get the clips off if you just take a little extra time and take out the t15s in the liner. Drop the liner and get to the clips from the inside, this will help not bend the metal/scratch up the paint.

Beautiful got the same one on my e93 same color space grey

Better off buying adjustable shocks like a set of bilsteins. That's what I put on my ram. I was told those leveling blocks are garbage and make the truck ride terrible.

What’s the update on this? How’s it looking now?

Your fuel economy is gone.

What spray did you use & where can I buy it

We are SICK and TIRED of Gloomy Grey and Death Black interior colors that became popular in 1990 and Every automaker has been shoving down everyone’s throats for 34 FREAKING YEARS ! My 23 Tacoma TRD Off Road has the Horrible Black Leather interior. Thank God Katzkin made me Lava Red Leather seat covers with black trim and stitching. I’m over the moon to get rid of some of that old outdated Death Black interior.

Too bad nobody told you the upper radiator support comes off in like 2 minutes and saves like an hour on this install.

Dude! Same thing happened to my maxpeeding rod coil overs in the rear. Not even 50 miles and the bushings almost shot out in the rear. I was lucky I had to adjust the height some more or else I would’ve been in big trouble. I read on a thread to just put the bolt in from the other side and that metal piece still slides into the back of the hub. Has been good so far.

Gorgeous and dependable truck❤

I want to do this when I get my car but why not just spray the black spray over everything that was grey when you seen the spray worked instead of putting the black pieces on ?

I did the same way without moving some things 😅

you can totally remove the headliner without removing any glass....

My silverado is basically this I used ppf but the flares changed the total look

Why we all keep the antenna in the same spot

No oil for PTFE seal

What type of paint did you use?

I run redline shockproof in my STI

How did it hold up? You still happy with it or would rather leave it alone if you could go back in time?

Thats how my car is. WTF would they 2 tone the interior

Same truck but doing a 2 inch level kit will same specs work?

The truck can handle the numerically lower ratio very well. I see leaving stock and enlarging the tires as a higher gear and savings on miles on the clock if you are still in warranty.

Speed is not accurate unless they reprogrammed...

Do you think you could get away with same tire and wheel setup but with a 2inch level kit with no rubbing?

i’m so glad this video exists, made up my mind to do this on my 1500, already have all the paint and dye. Gonna start the process in a few weeks

too much sh*t talking.

Thanks for posting this. Was On the fence of going cheap again like my first e39, but remembered all the shenanigans like cutting the sleeves and the stiffness. BC’s it is!

I have a question bro! Do you have to use that sealant from fcp specifically? Is there any other sealant I can use? Thanks in advance

I like how you actually show the process literally , nice vid bro thanks

Another Jerry with a J that daily's a 03 ep3 that was originally silver😂 right here

Will I blow up my truck or screw anything up running 37s and 3.42?

any difference in mpg?

Great video. It took me many attempts to, with all bc the screws. I had to rotate the crank to use a new location on the seal with the screws for each attempt. I used a torch to heat up the block around the seal, may or may not have helped. Finally got it

Dudes a nerd 🤓 nice truck tho bro i just got a rebel an tryna find a kew lil build

Did you ever compile a parts list for this project?

Oh, man, I just picked up a 2020 Warlock so I could retire my 16 Rubicon as my daily driver. Only thing I don’t like about the truck is that awful beige on the top half of the cab.

How do you like the 4.56s? Would it be a huge difference to 4.10s or possibly 4.30s?

So did this actually fix your problem?

thanks for this vid bro. a godsend for a dude with an 04 with a leaky valve cover gasket dripping oil onto his exhaust and the synchros on their way out. good to know that these are both known issues with this car.

Nice truck! What’s the part number for that s type muffler? Sounds great!

I’ve been trying to find a video to replace the interior with out paint but with cloth interior

I’m kinda sad for that m3 🤦🏻‍♂️

Send me ur number please I need u

Lame

Sweet ride!

Awesome effort with the video but I'm so sorry... No cigar. See, i was about to try this but you don't detail exactly where you need to put the jack in order to keep it (the engine?) suspended. If I'm missing something please let me know. I feel like you skimmed over that part a bit.