วีดีโอ

I unfortunately tried this and I ended up snapping the bracket that holds the switch. Has anyone found a place to buy just the switch? I can't seem to find one.

You could have put the pipe in your lathe to cut it quickly and neatly.

Great job bud I would offer some advice that if you left a slight shoulder to locate the sprocket and this helps with positioning and squareness.

Well, mate. Good job so far. Try to disassembly the whole wheel so u can rework a little better. Your wheel is quiet a bit rusty... Also at the lathe, when u disassembly the whole thing, u can do a better job at the lathe. ..and your welding's grind it a little bit down so it look nicer. Overall, nice job man. Really good centered!

Love the design it would look good outside a mansion

That first vacuum is a Bissell and it is quite good!

You should get a riding mower and change the pulley ratios and make it fast

If that line is the tdc line then it's likely normal...

Another good one to look out for is piston slap. Im not sure of the exact ways to tell the difference, but i have noticed that it seems to get louder with your exhaust (like if you take your muffler off, its still louder than the exhaust note) and that it usually goes away with a hot engine. My 01 malibu with the gm 3.1 v6 had it pretty good but always ran great

Naw it's definitely just rod knock

Dude why is your 4 wheeler so much hetter than mine💀 almost like u didnt bail off urs at 30mph hecause the throttle stuck😄😅

nice video mate

it will either work forever or not work at all(prolly still works)

that thing had so much blowby evewn beofre you started LOL.. no wonder it had no iil.. it had all been blown out the crankcase vent LOL its wnder the thing started at all

that poor lawn mower

Nice I just started to mess with these vacuum motors and I was wondering just this!!!

Cardboard head gasket 😂😂

That was impressive holding the camera and then engine blocking at the same time

Do you still have the deck for it if u do I’ll take it😂.

I wouldn't want this clown doing electric work for me or anyone!

i did not look at the date and i was not fooled what a turd of a video

haha you got me.

What a joke. Sad

So now you know , that electric bill is running to somewhere you didn’t expect , and no one told you about . I ran across this issue a few years ago . My father in laws father ran an electric service under ground to power his barn . My brother in law didn’t give a shit , and ran that bill up through the roof ! And didn’t even try to pay for what he used . Merciless . So when you buy a house , ask about it . There are some sneeky buggers in this world , who care less if your world comes crashing down or not . They steel anything if they can get away with it .

fakery

Volts....good stuff

Call the power company

I’ll never get back those 2 minutes of my life that I watched of this. Because of that, I label you a thief for steeling my time.

You did this on purpose, you're reported

OSHA would defecate in their pants watching this video.

FFffff f f f ff ff ff AAAAAAAAAAAAAAAAAAAAKEEEEE

I knew this was a fake video as soon as I saw the 4wheeler running. Those things don't actually run.

i noticed he wasn't concerned about getting electrocuted. no gloves. i noticed he took the meter directly to the battery without changing the range setting to DC volts. so he was trying to measure AC on a DC setting. nice work destroying your fan and charger..bare cables lying in the ground, yeah it looks fake to me.

Coulombs ... not voltages, duh

You should cut the cables and pour the electrons into buckets and sell them at the flea market.

Nice April fools

lol, they just run off to a car battery somewhere, nice one 😂

A funny fake. 1. There is AC on the cable, your Multimeter measure DC. 2. The charger was manipulatet ( you can see the housing is broke to open it before) and there is only a elektrolytik capacitor inside. It is normal that it explode when in short circuit with AC. 3. You manipulate the fan too. But a funny video😉 Sorry for my bad englisch, i am from germany.

Try measuring AC voltage instead of DC

GAYKE AND FAY.

I hope this is an April fools video because it looks quite scary and live wires in the ground lite that do not make sense. If not, then please be careful so you do not get electrocuted. Those wires probably got an AC voltage (just like inside your house), there is a switch at the right on your multi meter that can switch between DC and AC.

Looks like there are a lot of amperages!

"How is there no voltages" 😂😂

i got 48 v and 1.2 amp i use 1 full bridge rectifier and a 220 MicroF and 400 V capacitor i fed it with a modified atx 13 volt pc power sourse. did i make somthing rong?

Why is there a push mower motor in the riding mower 😂

Your father must be so proud.

Very informative video. Lots of repair videos on your channel, Are you up for a collaboration? Hipa supplies parts for small engines and maybe we would work together to help more people in the community.

Where do u buy parts

Lol

Cool stuff. Exactly the kinda projects I was doing in the Mid 2000s like go-karts with alternators and lighting.