วีดีโอ

Hey great video! Thanks for the information. I’m trying to figure out if I can do this with a greyhound m66015 212cc 6.5hp motor. I just got a mini bike with that motor on it and have not taken it apart yet.

Thank

Great basic video on tightening the chain.Thanks.

I am a smoker so I just use a old cigarette pack to adjust spark coil. or construction paper works also.

NC is normally closed, NO is normally open

Gas tank mat be loose. Hard to tell from video

That kinda sounds like clutch noise try taking your clutch off and run the motor

has this video been edited to show correct wiring as mentioned in comments ???

THAT IS A GO- CART CLUTCH PEOPLE!

When your clutch is rubbing on the chain, it means that your sprocket is too close to the clutch…. People always come on TH-cam and posting shit…..They don’t even know, all they want is a thumbs down.

you just confused everyone when you said plug into no1 and then said plug into nc1. I guess I will try not to fry my board tommorow since you are not replying to my email

dude are you sure about this? Looks like you fried that board

Well done!

Do you need 2 of these relays to start and kill the engine or just 1? Also how do you do it?

I have a remote start that i hooked up to the solenoid but the off button just stops to starter. How do you get it to kill the engine?

I have a 4 ch remote so I can use remote stop too. But no video of how to do it..

How do i properly clean it? Mine has oil coming out

this was the best video i watched yet thank you

I believe that the knocking may be a misalignment in the perpendicularity between the crankshaft and the cylinder caused by the stock crankcase side cover. The piston shows this misalignment by the wear marks on opposite sides in contact with the cylinder, one side the wear is on the bottom and the other side the wear is on the top of the piston. The stock connecting rod hit so hard on both sides between the piston pin seat that the pin got stuck in the piston seat. I replaced the connecting rod with another one and relieved about 500g of the stock flywheel and the knocking decreased but still continues. I am looking for a tool that can measure the perpendicularity between the crankshaft axis and the cylinder axis.

Make sure your running the right oil 10w30 or 5w30

Can you use the no and nc slots on the first relay

Great videos. I learned from one of your 2:18 video( 1 relay chip) the setup for a wireless remote starter now to setup a kill switch do I need a relay with two chips, Thank you.

So I recently bought a used Coleman. Apparently it has a torque converter on already. But it's missing the belt and front pulley. It just has the pipe that spins. I need the front pulley and belt. Do they sell just those parts? What will that run me to have a mechanic fix it?

So I recently bought a used Coleman. Apparently it has a torque converter on already. But it's missing the belt and front pulley. It just has the pipe that spins. I need the front pulley and belt. Do they sell just those parts? What will that run me to have a mechanic fix it?

Mine start’s first pull

Do you know what I should set valve lash to on a 212 hemi?

Every 3 oil changes or so pull the side cover the rod bolts come loose after time especially when it’s on a mini bike happened to me also

For first time,shade tree mechanic(me) I did perfect thank you awesome video no dumb long explanations for something simple good work

We’re did u get the brake line from

Are there any videos where they also explain the choke?

What does the choke do?

mine is shooting flames out of the bottom of the exhaust is that normal?

Any ideas why my gas doesn’t empty out of my fuel line?

just watched your video and was wondering if I could do the same on a 13HP generator motor so it would charge the small battery?

Until you realize any small engine does this

Bro I wasted time watching other videos THANK YOU!!! For being simple and straight to the point but also informative it is very much appreciated

My choke has to be halfway for the bike to even move lol

Pls make a how to video!

Thanks so much dude

is there a flywheel for predator 212 ghost?

Does it work with Lite 4

Thx bro helped alot

Appreciate you bro

question will this work with a 224cc predator engine?

Thanks bro

😂😂😂

On my brand new 212 there’s a screw that came loose inside and was rolling around near the flywheel. Any idea on where it coulda came from?

What size is your chain?

so, my 212 has a pretty bad knocking problem at higher rpms it always has but I didn't return it because I thought it didn't matter. what should I check first to fix it?

You should do a tutorial man that would get tons of views