วีดีโอ

@@EvgVrz that was with a new pack with barely a few flights on it. Flight time was similar to a typical new one, so the capacity should be in the 4xx mah range.

@@chrisbee5481 I have the O4 (light) and O4 pro and I am making a video on the Betafpv Meteor65 with O4 on it. Stay tuned! I also have the O4 Pro mounted on my another Toothpico (v2 lol) and I am testing that as well.

@@mia_filmz I will think about that. Are you looking for flight time and performance difference when using different size packs?

@@flyingpudding I’m looking for beginner guide, how to pick the right batteries. What charger are you using, how you charging etc.

@@haticeyldz6829 Assuming you have this FC in your metoer85: betafpv.com/products/f4-1s-12a-flight-controller It is likely that you can use the PINIO LED with it as long as you have at least one UART still available. Note that the LED strip cut line may not align to where it started with your frame, be creative when mounting it.

@@chantom6548 You mean on top of the O3 cage? Yes, as long as you put some insulation in between, as the O3 (or O4) emits quite a lot of heat. A better place to mount would be on top of the camera.

@@reditoyongco7343 please see the description and thanks for watching!

@@Copterlord good tips, thank you very much on behalf of everyone!

@@SkyReelsFilms Thank you very much for watching and your comment!

@@keithpederson3629 It should only go one way. You may look at the socket on the O3 and check the relative position of the pins inside - they are closer to the bottom. The O3 cable plug also has slots closer to one side - check before push the plug in.

Unfortunately, I can't recall the name. It is a 2.5" toothpick frame from maybe 4-5 years ago. I just put together another one using a 86mm frame. It is built slightly different to accommodate the smaller wheelbase. With the introduction of O4 Pro, it is now even easier to get lighter without sacrificing pic quality and durability. Will test once I have the O4 Pro on hand.

@@igorgoga7985 I am sorry that it didnt work for you. You may find me on IG flying.pudding and show me your setup, I will do my best to help. Cheers!

@@kewu-q2p Thanks for watching!

@@GarionPhotoTech Thanks for watching!

Thanks for watching and your comment!

Thanks for watching and your comment!

As far as I know, it would only work if you cut at the cut line instead of anywhere. Try re-routing the strip so that it wraps around the hoops properly. You may apply new double sided tape if necessary.

@@flyingpuddingill try that thanks

@@Rav373- Thanks for watching! Yes, you will enjoy your Pico a completely different way 😉

You may use the binding procedure on this page under "Serial ELRS 2.4G RX": betafpv.com/collections/brushless-flight-controller/products/f4-2-3s-20a-aio-fc-v1

@@SkelaKing It doesn't seem to be available now, and I found a similar one on Amazon: a.co/d/4MiqWsu

@@flyingpudding dang, that looked like a really good one! I’ll keep looking I guess

@@gamingisnotacrime in case you have the bnf version, the PINIO LED is already hooked up to UART6. There is no need to enter CLI command to remap the resource as it came preconfigured. Just find USER1 under Modes and assign a radio channel/switch to it, and set the range accordingly.

@@flyingpudding i bought bnf, but i update the version of betaflight and forgot to the backup, what commands i need to use for using user1 in modes for turning on and off leds?

@@gamingisnotacrime no prob. U may follow the instruction on their product page: betafpv.com/products/pavo-series-cob-led-strip Make sure you adjust the procedure and reference UART6 (where the LED is connected in bnf) instead of UART1.

I am glad that you found my video useful. Congrats and happy flying!

I’m getting my nightlife edition this saturday. Hope I like it. How I found one in stock is… I didn’t. Sadly I’m paying resale value. It’s new and sealed tho

I think you'll dig it. I'm still loving mine. I think I would have been just as happy with the standard edition Pro, though. I rarely use the LEDs. It's fun to cycle through the colors, but you can't see them when you're on the goggles. Entertaining for spectators or if you're chasing your buddies' lighted quad. I do like the smoke colored canopy and props. I think that if I had to wait longer for the Nightfire Edition or if it was significantly more expensive, I'd just go with the standard edition Pro. These things fly great. I'm having a blast. I hope you enjoy yours too.

@ thank you so much

Thank you very much for watching and your comment and sub!

Thank you for watching, happy flying!

You may want to follow the instruction on the product page. betafpv.com/products/pavo-series-cob-led-strip

@ thank bro

@ In the end, with what you have happened to me, user1 came out but I have assigned it to the controles and it does nothing with the leds

@@TheDavid76 which UART is it connected to?

@@flyingpudding Usb vcp configuration on, uart 3 rx serie on, uart4 configuration/MSP on Periferic VTX(MSP Displayport)

I did not and there doesn't seem to be a way to calibrate, please correct me if I am wrong. When you say yours is wrong, is it consistently 20-30m higher or lower, or the value drifts in both direction? If it is the latter, I found this video that you may want to check out. th-cam.com/video/bSje9viDLIQ/w-d-xo.html

@flyingpudding perfect thanks. Its drifting. The Video is perfect 😀

@Travlie Glad to help!

@@gf6000 Yes. Thanks for watching!

@@macaronpompom88 thanks for watching!

@@TNPilipinas Thanks for your comment and sub!

@@garionhk beginner friendly too! Wink wink!

@flyingpudding very attractive. But need to wait as I bought a new camera 😅

@garionhk just look at the price of the kit, it's peanut compared to your camera lol

@@AndresLugo-g8v shorturl.at/Hgaan

@@ThaDuDeMaN1 maybe you want to look at the Pavo20 Pro instead? th-cam.com/video/ssgQqJs1ktY/w-d-xo.htmlsi=4TOaizBPIpWn7q5s

@@smokeyboi9365 that is correct. Lipo is 450-500mah 2s.

@flyingpudding thanks for replying. My raw fpv is 83g then my batt is 32g CHNL 2s 450mah. Cant get it below 100g. Any advice?

Im leaving soon going to Japan and I want to bring my pavo pico but unsure coz the of weight. Total of my setup is 114g including the batt

@@smokeyboi9365 a typical 450-500mah 2s should weigh around 28g. That means you have to get the dry weight of your Pico down to 72g or less. Are you using the stock setup or is it a custom build?

@@smokeyboi9365 please refer to my stock build video here th-cam.com/video/X-1k9NEGrs4/w-d-xo.htmlsi=X1uXB354LzSCd5iz

@@LayinLo Yes, assuming that you are also using Goggles 3.

@ yes I bought the avat 2 creator combo and just picked up the controller 3. I’ve really been wanting a micro drone for indoors but I saw on a review it didn’t work for this guy who had the controller 3 but he was in Africa so I dont even know

@@LayinLo Controller 3 transmits signal via the Goggles instead of to the air unit directly. Maybe he set it up incorrectly?

@ hopefully he did cause I just purchased the frame and 03 unit. I’ll make a video unboxing and trying to set up 🩵

@@LayinLo Look forward to it! Happy building.

Both Pavo20 and Pavo20 pro uses the same flight controller. According to the info on the product page: betafpv.com/collections/brushless-flight-controller/products/f4-2-3s-20a-aio-fc-v1 it doesn't look like there is a target for iNav at the moment. BTW, are looking to add a GPS module for RTH function? You could use UART 6 for that.

@@yungerallenelectricalcontr6415 Congrats and thank you for watching!

@@jackguido4532 Yes! It is totally doable with Pavo20 as well. You may want to use a 2s pack instead of 3s to make it easier for altitude control and weave around tight corners. Happy flying!

@@flyingpudding ah ok so having a 2s will make it less “reactive” ?

@@jackguido4532 Yes. Also a lighter setup is better for fine controls indoor.

@@flyingpudding i tried your rates and they fit perfectly for flying with less reactivity and more precision. Thank you so much

@@jackguido4532 I am glad that it helped, happy flying!

@@janernstd9842 I did not. Regiatration is not required when using a lipo that weighs less than 28g - making the total all-up-weight (AUW) below the 100g threshold.

@@flyingpudding So no problem on airport inspection of drones?

@@janernstd9842 Yup! I went through security at multiple airports without issues. Just pack your stuff neatly, see this vid th-cam.com/video/ep8KoVWcjjU/w-d-xo.htmlsi=Cu85qHIqanhIdd5-

@@SiOgie Thank you very much, I am glad you enjoyed my content. Stay tuned!

@@nebz_fpv Thanks for watching! Don't forget to check out my Toothpico video too! th-cam.com/video/JrTMNojF4II/w-d-xo.htmlsi=xt8VfMPSbEVXypxq

My guess is that it is a logical choice to belly mount the lipo while the O3 is on the top; so that CG is balance. Another advantage is prop clearence is better especially taking off on rough surfaces. It's also very easy to swap and share the O3 with my other quads. On the other hand, I have been an adroid user for over a decade so I feel you! We pilots always welcome more competition and I think Walksnail Moonlight is a good rival.

@@donquibtc theoretically yes, but it will be underpowered. Keep the weight at minimum and it should still be ok.

It is designed to be controlled by an auxiliary channel. Assuming you already wired up the LED to an UART and performed resource mapping correctly. You would then setup a switch on your radio, map it to an aux channel, and setup a range under USER1 like here: th-cam.com/video/ssgQqJs1ktY/w-d-xo.html

I can't seem to recall that I mentioned "sbus" in this video. Would you mind telling me the timestamp and I will look for it?

@@flyingpudding sorry , wrong video I was watching so many videos at the time got me all confused :) this vid helped set my Pavo up thanks!

@@retro93277 Glad to help, happy flying!

Congrats and thanks for watching!

@@mattvesta5721 not all the shots 😉

@@jcsuarez8970 DJI FPV Googles v2, Googles 2, and Integra are compatible with O3.