วีดีโอ

Great video. Thanks

Anyone else have trouble with the tight space between the cat. And frame it bent my upstream sensor? Thinking on wedging a section of exhaust pipe in between where it won’t bend the tip again. Thoughts? I have a 98 1500 4x4

Right on dude, thanks for this video. I'm watching it almost A DECADE LATER LOL. My '98 1500 5.9L has been having idle issues and research has led me to O² sensors and this video. The idle issues are sputtering and sometimes dying, RPM drop, and a sucking/hissing sound as well as acceleration weakness and backfiring. Hopefully changing the sensors will be the solution.

I just ordered 13.5 shocks to raise my 04 sportster 1200 cause it was lowered and I kept shredding the rear tail light wiring harness.

Great post, glad that I found out where the little shim went as I thought it was some kinda contact that had fallen out. Thanks

I have a P0133 code sensor 1 bank 1 slow responce, need to replace sensor this will help a ton thank you! If you know any videos on cutting corrosion and extending the wiring harness to the battery terminals that would be stellar.

Where was the downstream 02 sensor, you mentioned it but never pointed it out.

I just use hydraulic angle wrenches

Still one of the best TH-cam videos for replacing O2 sensors on pre-2000 Rams. The upstream O2 sensor is definitely a bitch to replace. I have a 1999 5.2L 1500 Ram, and it's been stalling during acceleration and running extremely rich. I hope replacing the upstream and downstream O2 sensors will correct the issue. This video really helps. Thanks for making it very clear.

Can you run 3 running brake light wire into the 1 main wire?

Will this work on 99 v6?

Ummmm ur not supposed to use penetrating oil or any oil on or near ur Catalitic converter... heat. Not oil to release

Where can I find that pig tail? I have a 06 883 that some one butchered, trying to re run the rear wiring

Good call on replacing the Ujoint also, since you're that deep into it. I did the same.

Couldn't you just burp it manually instead of the airlock? The pressure release will do it at a certain amount of pressure from the co2. I'm wanting to age mead in bulk but I'm short on space and primary is plastic bucket not good for aging. Would the keg work for that?

how did you move the outside wire covering? it dont slide easy

I had to dig through quite a few videos to come across this gem! Thank you for helping a fellow 2nd gen owner from breaking the trim trying to rip it out.

Hello great video. Did your check engine light clear or did you have to clear it with a scanner. Thanks

Thanks for the effort and data- much appreciated

thanks men great video

I have 1999 5.9 same issues crack dash, power seat fail,bad gas mileage dead miss that came and left after Seafoaming, intermittent AC, still love my old truck

my truck doing exactly the same thing. I just don't know if I should replace the bearings or the whole hub assembly.

Instead of waiting for a buddy to tell you you should use gear oil in your primary, it would be faster to look in your manual Didn't check date, you've probably already found out since this is 4yrs old

Hi Scott, great vid's thank you. What size tyre have you got under that wide glide fender? I have a 2012 wide glide with standard 4.5" rim and 180/60 17 tyre, and wanting to put a 200/55 17" tyre on 6" rim

I'm trying to connect 4 wire trail led lights to my 2008 sportster where there 3 wires. Help.

Where can I find the red gas caps and speedomiter setup?

How about actually removing a panel while we are watching.

Thank god someone else with a single cab so I can know for sure the speaker size.

Thanks, my truck is doing the exact same thing. Getting them replaced soon. Lucky I have a couple tickmin spares

Haven’t show us how to put the whole housing back in and tighten it to the handlebar. I found that very challenging 😞

Thanks. Helpful. I was looking for how to remove the trim piece from the seatbelt to access the bolt. It looks like it slides down from the top.

Bro this just happened to me two days ago. I did everything you said. And Done!!!! Lots of thanks!!!!

Very informative. I wish you had shown how you got that extra wiring to fit inside the housing. Pretty tight in there!

You sir are the man! Thanks so much!

I cought on to the metal bracket👍 my plunger was stuck in the housing. I tried to pull it out to clean & lube. It came all the way out "completely"☺ spring & all. I put the spring & plunger back in. Now my brake pedal works again. I'm going to have to replace the fbs. But after watching your video I feel a whole lot more confident about doing it myself. Thanks Bro.

Your videos are great and very informative. Sorry about the typo!

Thank you for your quick response. Your videos are great. You are girl and very informative. Rffr

Is this the same or close to how to replace a switch on a 2003 883 hugger? You da Man 👍👍👍

Hey Scott I have a wiring question would you mind messaging on FB about it?

What about the downstream that you mention?

Hey Scott, hope you can help me. I have the exact same bike and I’m trying to install the original brake light, the thing is I get the running light, plate light but no break light, neither when I hit front or rear, could it be any switch? I’m getting a headache from this...

How do I remove the bolts on the seatbelt

Doing my 99 right now. I used a 22mm tight fit. Crazy how that’s the driver side upstream when it’s on the passenger side.

Isn’t the orange and brown the turn signals? Lol

good vid, great detail but you dident touch on how exacally the swtich is oreintated and how the meatal bracket holds the switch, i do belive mine is bent , is hard it seems to find a vid showing this, wires coming out of switch face up or off the side?

Dude, your sound effects are spot on with what I hear on my 03 Ram1500. I guess its time for wheel bearings at 196k miles on it. Haha

I have a 2000 ram 1500 5.2L sport and I was able to use O2 sensor socket right to 3/8 socket above catalytic converter. Advanced sold me the wrong one too he said his system showed 4 02 sensors but there's only 2 the upstream one has gray pigtail terminal with slots at 90 degrees and the downstream is black with one slot at like 75 degrees unless someone messed with all the wiring

How did the beer turn out buy soaking the wood chips and cocoa nibs turn out doing it yhat way

anybody know what that connector that he cut the wires is called? part # would be nice. thanks!

you use the 12 or 18 inch sensor the sound went out? same symptoms in my truck. looks like you went with the 18?