วีดีโอ

Wish this was a full rebuild. Mine is leaking from under the flange with the two five sided bolts.

GOOD VIDEO, INFORMATIVE VIDEO

Tengo uno igual al suyo , gracias

Thank you

Slop is pig feed,you mean Backlash.

Thanks a lot pal, really appreciate you!!

hi cool video what is the liquid you put on the letters before tracing?

how did you get the speedo needle back on correctly?

In my case there were three clips on gears. I don’t remember where the third was. It’s a little different, it has a bent tab to allow pulling it

you did an EXCELLENT job explaining this; great communication skills! No BS. Straight up tear down and detailed reassembly. THANK YOU! >>>>>>>Merica!

Really well done video. Did you end up painting it?

Great video- thank you

Is it for sale? I'll pay you a good amount

i am doing this exact thing right now. my circuit board is pretty ugly also but i didnt find any open traces. the anode leg of both capacitors snapped off really easily when i barely touched them so i am going to replace them both and hope that is the fix. the big one is 100uF 25v 105C, the little one is 10uF 25v 105C. $5 for 5 each on amazon. i set up a bench test to test it with the speed sensor also. +12v to speed sensor pin 1 & IGN on the board, -12v to speed sensor pin 2 & GND on the board, speed sensor pin 3 to SEN on the board. rig something up to turn the sensor with a drill, needs to have plenty of slop in it so you dont break the little plastic gear.

Excellent work. I just pick up an older New Hermes. It’s good to know the rotary feature can cut more than plastic.

For anyone watching this with any hesitate, dont worry. Southbend 9 aprons are super simple. If you have trouble remembering locations, take a couple pictures but you really shouldn't need to. Go for it.

I have an old benchmaster machine, works great for my needs

Hi, Could you please tell me the model number of your New Hermes engraver? I just bought a similar one, but can't find the model number. Mine is manual, not motorized.

I have a Benchmaster. I want to know if there’s somebody who has the original auto feed, who can show me how it works. Those are hard to find

Awesome, really beautiful tag and great video!

Have you considered a height extension? I want to do the dro to mine as well as try to make a height extension to help out the limited height when using a vise or rotary table. Would love to collaborate

Have you done any cutting with this machine like to see what it would do a buddy of mine just picked one up I'm going to make a video of it and put it on my channel we're going to go over it and get it fixed up

Adding this one to my saved videos for the future. Haha

Awesome work! I just picked up a non running benchmaster mill for $50 last week, took an afternoon to get it cleaned up and running again, and now can't wait to get a DRO on it. My only problem so far is I can't get the Y axis trammed in, any tips on adjustment on the Y? I got the X axis dialed in to 0.001" over ten inches but can't figure out the Y, I'm hoping it isn't non adjustable as its out about 1 thou per inch.

Thanks bud

I have a benchmaster. What dro did u use? Where did u get it?

Could you do more videos on the bench master. I remember you saying you could do a gear cutting video

Excellent video !! Thank you .

I have an RC2510 that has no spring. Would that be an older model?

Nice beefy knee table on these benchtop units but too limited without a lever action quill for my liking. Good video and tidy organized space.

www.youtube.com/@technicalmind1299

Muchisimos pasos para hacer una chapa de bronce grabada..

Gracias saluddos desde bolivia

Thank you for information

I have to do this job soon to a Heavy 10R. You make it look so easy! But the price for that kit has gone up a LOT in the last 4 years. Thanks for a great video!

Hi i hv a enerpac hand pump. When i apply load to system i lose at least 1k psi When i put it on hold. I DONT HAVE A LEAK. Im using a digital pressure gauge for the test. I cannot physcially see the cylinder retracting bk. So how do i go abt troubleshoot this problem sir?

Definitely the best video on how to rebuild the apron. Do you have any vids of rebuilding the other components on the SB9? Just wondering what you use for way oil as well? Only real way oil I can get is sold in 5 gal quantity, so I'm looking for an alternative, heard engine oil work well

That's clever. I've done the same with a portable jump starter to get my wall charger going.

Great video! Pronounced HER-mees after the Greek God

very helpful methodics! a new subscriber.

How does the worm gear really come off. at 7:06 or so, it magically just comes out, but not really seeing how it got there.

Peace ✌️

I wish I grew up with a father…😢

Sweeet. Nice to see a fellow Benchmaster owner giving new life to these little tanks.

Can I ask what DRO you used? Was it a complete kit?

Very cool! I just picked up a Benchmaster mill today. I'm sure I will have some questions for you.

excellent explanation.

I have something wrong with my hyper tough drill and I had to put battery on a charge with different source than the charger cause the drill has about 1000 ohm draw while not running

Awesome thanks