วีดีโอ

please free send me

For hmi it's very easy. Direct driver supported

Can you pls share me demo video or program for the same????

you can download it from www.renuelectronics.com it's FREE !!!

Please check drum Sequncer video maybe that will help you. If you are Communaiting with dop Or other hmi then it will be very easy to understand

@@demoplcprog540Thank you very much Bro.it is working very well, can you post video about how to programming two dtc1000r at a time with delta plc

For dtc and hmi direct 485 communication can be establish. And for hmi and plc use 232 communication.

You just need to take next tag I.e. for first 16 tag you are using D0 then for next 16 use D1 similar for next 16

Did your issue solved?

Ok . But In alarm setup if I have taken alarm adress D1 Nd of I change to D2 will . Doesnot D1 get over write.

Where should I write the adress for next 16 tag.

@@gauravshah3246 your alarm 17 by defult go to d2

in DOP configuration-->control block

you will find clear history buffer option

for communication you just need a mod bus address of driver there is no change in program please see the manual of VFDE700 there must read write mod bus address

@@demoplcprog540 noting happening

@@gameeducation1343 can you give me modbus address of VFDE700

@@demoplcprog540 Please send me your email So i would send you manual as well. The problem i facing during communication the error name E.PUE i tried so many tricks to remove this error but failed this error occur only when i run the delta plc from stop The register use to write for change the frequency of mitsubishi E700 drive is HD.

If you send me your email i could send you the program too

just tell me what you want i can try to help

no its an garbage value.give right sensor type to DTC.

Bahi ek sw ziada temperature controller kay lie yahi ho gi Programing D1050 Secnd kiya ho ga d1051

NO,2 controller device id is 1 and 2 address will be the same i.e.D1050 .you need drum sequence prog to move the value

which inverter you have ?

Didn't get you what you Exactly want

@@demoplcprog540 how you will increment and decrement in this flexi hmi

@@priyam1776 in counter there is direct increment and Decrement counter given

use CTDr and CTUr for counter with rising edge detection

if you want rising/falling edge in contact then select that contact and click on space bar for changing contact type

DTC you can add multiple sensor like even current or voltage as temperature sensor having more options like graph, control, alarm etc more details are in manul. Still if you need something you can ask me.

just go to historical trend graph and choose curve field more than 2

How to tag for two curves, bro? It just have a tag in history buffer setup!

th-cam.com/video/JM9f_Zuqzkg/w-d-xo.html Check this out

Yes off course.. no issue with that

@@demoplcprog540 thank you..could you please provide me the required instructions for communication and read data from pm2120 because I have tried the program in your video but I can't read from the controller.

Just give me yaahikawa modbus address and communication protocol I can send you prog.

ok i will post video for it.sorry for late reply

@@demoplcprog540 It would be very interesting because I want to rescue the historical

Addressing of dtc will be chenge viz k1,k2,k3,k4,k5. But you also need drum sequncer otherwise your PLC show faulty value

Raheel S ok I will check and revert to you send your mail id

Please check what value it shows in 1012H and 1013H register You can also set it If it shows 100 and current is not 20mA then device must be faulty

I will try to upload with proper example In Delta all modbus value show in one register i.e d1050 So you need to move value continuesly to other data register with proper Interlock otherwise it shows same value for all Reading.

@@demoplcprog540 NICE I TRY IT IT WORKING

4-20 can be possible without any setting