วีดีโอ

Hi, please i have issue with the model/geometry. I am finding it difficult to integrate the bluff body

you did not define temperature of bluff body

very useful, i'm from 2024

Thanks

What a great video I need your email sir

how to determine cell height?

Hey i get a floating point exception following the exact tutorials. The reason is one of the values is being initialized to a very high value. Can you please suggest what could drive this?

Sir can you also share video of hydrogen and air mixed Combustion proccess

Sir please can you give reference of the Paper of Brookes et al I cant find that paper .

Respected Sir, I tried it but its not working could you please help.?

Sir I am beginner and facing some problem could yoj please help.

How can i adjust injection point i mean there is only adjustable x position value for injection but i can't use carry injection point to a specific position depends on also y axis

hello i want to do the hydrogen air premixed combustion so for that i need hydrogen air mixture file so how can i create that?? plz tell me

Thank you! My first successful combustion simulation.

How can we set particular injection pressure?

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (th-cam.com/video/ASbKmvygQEo/w-d-xo.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (th-cam.com/video/ASbKmvygQEo/w-d-xo.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (th-cam.com/video/ASbKmvygQEo/w-d-xo.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

hi sir! great lecture. Can you send me or post your email id , I have some question regarding a problem I m working on? thank you.

👏

Very nice tutorials sir. Thank you so much

Cant we select laminar model instead of turbulent ( for orifice in microchannel - study)? Also if we take inlet boundary condition as inlet velocity, then what is the range of velocity that we can give here? Kindly guide

my mesh fails due do conflict in regions for a u bent pipe.

Hi sir, I tried this using species transport but the mixture didn t ignite, do you have a suggestion for me please?

Sir is it possible to analyze mixing of co2 gas with cold water in a pressurized vessel in ansys fluent. Suppose a vessel is in vertical shape( 400mm diameter × 1700mm height × 3mm thickness) and vessel is half packed with series of perforated plates and then we pressurized that vessel from co2 gas up to 5 bar which will remain constant throughout the simulation or process.Consider half inch duct for co2 gas inlet from any side of vessel and then with the help of high pressure pump, cold water(2 degree celsius, volume flow rate 4 cubic meter per hour)is sprayed through nozzles from the top of vessel towards bottom. My goal is to look out how water is passing through those perforated plates and at last how much co2 gas is mixed in water which is going to be stored in the bottom of the tank . Consider 1.5 inch duct for water inlet and 1.5 inch duct for water outlet which is open to environmental pressure. Kindly explain how to do in ansys fluent . Thanks a lot 🙏.

Thank you so much for the video. Could you please tell how the boundary conditions of air and fuel inlet mass flow is calculated. Is it assumed to be the same value as 3D case or do we need to make changes for the actual values for 2D. or is it accounted when you gave hydraulic diameter ?. Thanks once again!

Nice Lecture Sir, 👍👍👍 I need your help with regard LES and DES for non viscus flow for two phase simulation. can you give me some linke which is helpful to understand the basic concept.

sir how to get area in reference value? is it car area ?

You're a life saver. Thank you!

hello, can you explain why the pressure at the exit is higher than the inlet, and we saw in your set up you choose the pressure inlet to be higher but in the results its the opposite. Thank you

do you have a paper validating the result

Sir, how to get the pdf wastewater treatment by hydrodynamic cavitation

Can you please make video on micro pre mixed Combustion simulation with the help of chemkin mechanism.

Hi Sir, how can simulate fire model for car ? how to model the smoke and visibility by using ansys fluent?

Can you please guide how to take average values of iterations we performed. And plot against those avg values

Hello. Thank you for the video. I have a question. At the start of the video it is shown an equivalent fuel/ar ratio of 0.61, but in the video, you don't set any fuel/air ratio. In general, there is no setting regarding the amount of fuel. How does the software understand that the incoming mixture has a fuel/air ratio of 0.61? Thank you.

Can you plz make a dynamic mesh video of this cylinder with valves and their timings

Hello. Thank you for the video. It is very useful. I tried the tutorial, but I run into the "Floating point exception" error when I start the calculation. What could it be about? Thank you 😁

Thanks bro that was so helpful for me

Really helpful, Thank you for you effort sir😊

I am not getting single orifice atomizer in 2D. It is only available in 3D analysis. Help pls

how do you get the fluid flow visualisation if you are doing in 3d?

@EngineeringNature hello sir, i have tried to do simulation using hydrogen-air but it's not working and shows floating point error.

Hello, any ideas on how to add Hydrogen to that mixtur in order to measure Nox?

Hii sir , I did this problem in the same way what you have done , we follwed this vedio but at the end we are not getting the results as shown in this vedio and as you said in vedio i searched for vedio of meshing of this one but i couldn't able to find it . Please help me by mentioning the boundary conditions you have taken in this problem, here Other wise drop your mail id i will contact you . Thank you !

hello can you make a detailed introduction of ansys spaceclaim or design modular especially for creating multiphase vertical pipe with two inlet

Hello sir , i want to know that can we do this method for another fluids like nitrgen and hydrogen fuels can you please help me with this.

Hi,can u tell me what is artificial walls on faces,please explain why it was showing on console

sir Top wall you didint name it (like inlet outlet and axis ..why sir

Could you please make a video of combustion in Scramjet Engine