![Richard Tait](/img/default-banner.jpg)
- 95
- 717 356
Richard Tait
United States
เข้าร่วมเมื่อ 15 มี.ค. 2006
This is where I talk about all things automotive. From fix-it to commentary, I let several years of experience with cars help you in whatever way I can. Feel free to like, share, subscribe and comment. All are welcome.
2013 Mazda6 Headrest Removal
Have you ever wondered how to remove the headrest from your 2G Mazda6? I must admit that I never gave it a second though...until I needed to. Let's have a closer look at how it's done.
#richardtait #mazda #mazda6 #tutorial
#richardtait #mazda #mazda6 #tutorial
มุมมอง: 138
วีดีโอ
2013 Mazda6 Driver's Door Lock Replacement
มุมมอง 2733 หลายเดือนก่อน
Join me as I replace the driver's door lock of my 2013 Mazda6i Grand Touring. Lesser and earlier models had interior door handles that automatically unlocked the door when pulled. This is a function of the door lock mechanism. When I replaced the door I did not swap over the higher spec auto unlocking lock and so I went looking for one and found it in a junk yard. Let's get into the process of ...
2021 Mazda6 Navigation SD Card Installation
มุมมอง 1633 หลายเดือนก่อน
The first video with my 2021 Mazda6! Join me as I install an Amazon aftermarket navigation SD card in the car. Did it work? Should you try it? Let's see... #richardtait #mazda #mazda6 #tutorial
2013 Nissan Note Gear Selector Removal
มุมมอง 3254 หลายเดือนก่อน
A short tutorial on how to remove and replace the gear selector in a 2013 Nissan Note DIG-S with the JATCO CVT transmission. #richardtait #nissan #nissannote #nissannotee12 #e12 #tutorial
2013 Mazda6 Map Light (Overhead Console) Replacement
มุมมอง 4735 หลายเดือนก่อน
Several years ago the very first thing that happened to the car was one of the buttons for the map light (overhead console) fell out. Several unsuccessful attempts to get a replacement at junk yards, I decided to do without because the OEM was too expensive and the aftermarket was of no help. I finally discovered an aftermarket solution...or so I thought. Join me as I show what I did and what I...
2013 Mazda6 Repair Update Part 4
มุมมอง 645 หลายเดือนก่อน
Some time ago when you saw this car it was practically wrecked. I'm in the process of getting it back on the road. The process has started and I'm working on correcting each problem, one at a time. Join me as I remove the non-folding mirror that came with the donor door and replace it with the new, model-correct mirror. #richardtait #mazda #mazda6 #tutorial
2013 Mazda6 Repair Update Part 3 - Mirror Assembly
มุมมอง 926 หลายเดือนก่อน
Some time ago when you saw this car it was practically wrecked. I'm in the process of getting it back on the road. The process has started and I'm working on correcting each problem, one at a time. Join me as I go through the process of preparing the newly bought OEM driver's side mirror (Part# GEG2-69-181A) for installation by swapping over a few parts from the original, damaged mirror. The ne...
2013 Mazda6 Repair Update Part 2
มุมมอง 1166 หลายเดือนก่อน
Some time ago when you saw this car it was practically wrecked. I'm in the process of getting it back on the road. The process has started and I'm pleased so far. However...all was not well in paradise. I have discovered a problem. Join me as I reveal what the problem is and how I solved it. Tool: 19 Piece Trim Removal Tool Set: www.amazon.com/dp/B0CMZ3ND9Q?psc=1&ref=ppx_yo2ov_dt_b_product_deta...
2013 Mazda6 Repair Update Part 1
มุมมอง 2196 หลายเดือนก่อน
The last time you saw this car it was practically wrecked. I made it my personal mission to repair it and get it back on the road. The process has started and I'm pleased so far. However...all is not well in paradise. I have discovered a problem. Join me as I reveal what the problem is and what I am doing to solve it. Tool: 19 Piece Trim Removal Tool Set: www.amazon.com/dp/B0CMZ3ND9Q?psc=1&ref=...
2013 Nissan Note DIG-S Transmission Cooler Installed
มุมมอง 8189 หลายเดือนก่อน
Join me as I give you guys a look at the transmission cooler that I had installed in my 2013 Nissan Note DIG-S. As part of this entire process I did an engine oil and filter change; a transmission fluid and filters change; and I had the transmission cooling block changed to one from a US-spec Versa. Below are the parts: Oil Filter: 15208-31U0B Air Filter: AY120-NS060 Transmission Filter (intern...
2013 Nissan Note DIG-S Walk-Around and Review
มุมมอง 1.4K11 หลายเดือนก่อน
Join me as I review this interesting little car, a 2013 Nissan Note DIG-S with the Nissan-Renault HR12DDR supercharged 1.2L 3-cylinder engine and a CVT transmission. I show you the features, the exterior, and the interior. This particula car is pretty special and I reveal just how so... #richardtait #nissan #nissannote #review
2013 Mazda6 Fender Removal Timelapse
มุมมอง 53511 หลายเดือนก่อน
Thanks for 1000 subscribers! Just a video I did while I removed the left fender of the car to take some pictures for the collision repair shop. Yes, my baby was in an accident and needs some work. Benjamin Tissot - Endless Motion Music by: www.bensound.com License code: FT9RKX05EDJAJLF3 Benjamin Tissot - ERF Music by: www.bensound.com/free-music-for-videos License code: 3P1MK7U9H68XOPE7 #richar...
2013 Mazda6...the unthinkable happened...
มุมมอง 27111 หลายเดือนก่อน
On August 13, 2023, the unthinkable happened. Join me as I reveal to you what happened and what has happened since. Major updates, all around folks! #richardtait #mazda #mazda6 #tutorial
2013 Mazda6 Door Mirror Glass Replacement
มุมมอง 1.6Kปีที่แล้ว
2013 Mazda6 Door Mirror Glass Replacement
2009-2013 Mazda6 Bose AUX IN Auxiliary Input Walk-Through
มุมมอง 2.7K2 ปีที่แล้ว
2009-2013 Mazda6 Bose AUX IN Auxiliary Input Walk-Through
2009-2013 Mazda6 Bose Door Speaker Replacement
มุมมอง 7K2 ปีที่แล้ว
2009-2013 Mazda6 Bose Door Speaker Replacement
Mazda L5-VE Engine - All You Need To Know...
มุมมอง 7K2 ปีที่แล้ว
Mazda L5-VE Engine - All You Need To Know...
2013 Mazda6 - Enable Smart Turn Personalization Feature using FORScan.
มุมมอง 3.4K2 ปีที่แล้ว
2013 Mazda6 - Enable Smart Turn Personalization Feature using FORScan.
2009 - 2013 Mazda6 Rear Door Card Emergency Removal.
มุมมอง 1.3K2 ปีที่แล้ว
2009 - 2013 Mazda6 Rear Door Card Emergency Removal.
2009 - 2013 Mazda6 Trunk Lid Stay Dampers Replacement
มุมมอง 2.7K2 ปีที่แล้ว
2009 - 2013 Mazda6 Trunk Lid Stay Dampers Replacement
2013 Mazda6 Rear Wheel Bearing/Hub Assembly Replacement
มุมมอง 5K3 ปีที่แล้ว
2013 Mazda6 Rear Wheel Bearing/Hub Assembly Replacement
Rich's Motorcycle Ad Commentary - Craigslist - May 24, 2021
มุมมอง 413 ปีที่แล้ว
Rich's Motorcycle Ad Commentary - Craigslist - May 24, 2021
Rich's Vehicle Ad Commentary - OfferUp - May 12, 2021
มุมมอง 193 ปีที่แล้ว
Rich's Vehicle Ad Commentary - OfferUp - May 12, 2021
Rich's Motorcycle Ad Commentary - OfferUp - May 10, 2021
มุมมอง 213 ปีที่แล้ว
Rich's Motorcycle Ad Commentary - OfferUp - May 10, 2021
Rich's Motorcycle Ad Commentary - Marketplace - April 26, 2021
มุมมอง 253 ปีที่แล้ว
Rich's Motorcycle Ad Commentary - Marketplace - April 26, 2021
Rich's Vehicle Ad Commentary - Craigslist - Apr 22, 2021
มุมมอง 253 ปีที่แล้ว
Rich's Vehicle Ad Commentary - Craigslist - Apr 22, 2021
Rich's Motorcycle Ad Commentary - OfferUp- April 19, 2021
มุมมอง 363 ปีที่แล้ว
Rich's Motorcycle Ad Commentary - OfferUp- April 19, 2021
Rich's Vehicle Ad Commentary - Craigslist - Apr 15, 2021
มุมมอง 193 ปีที่แล้ว
Rich's Vehicle Ad Commentary - Craigslist - Apr 15, 2021
Good video i didnt succed though besuse i couldnt remove the bearinghub.my intension was to replace the dustshield
@@jarkkojussila7609 Sorry to hear about that. That's how it is sometimes. Sometimes you just have to step back, take a breather and try again another day when you are in a better place mentally or physically. Having the right tools and the right mental approach makes all the difference sometimes.
Some commentary or explanation would go a LONG way.
Does the 1st generation mazda6 also has this feature? (2005-2007) thanks!
The 1G has a similar feature which is called a "Lane-change signal". The owner's manual says: "Move the lever slightly toward the direction of the change―until the indicator flashes― and hold it there. It will return to the off position when released." The 2G will automatically flash 3 times and then cancel all on its own, while the 1G is manually operated. I hope that helps.
Hi great video what was year of your car please?
@@user-oq1yw2ji6j 2013 (it's actually in the name of the video 😜)
Hi,, where did you check the torque of the screws? Thanks
@@EOVargas I got the torque figures from the workshop manual.
@@RichardTait1977thanks bro, did you buy the workshop manual at the dealership?
@@EOVargas No. I bought it on eBay. The two volumes cost me $60 shipped a few years ago. Best single $60 I've ever spent on this car!
Thanks!!!
Excellent video! I appreciated the step by step instructions. Your explanation made the job doable!!! Thank you very much!!!
You're very welcome!
I appreciate this video, just did this job today.
@@user-rt4ct6tq3r You're welcome. I'm really happy that these videos are still helping people. That's why I do them.
@@RichardTait1977 My daughter was especially grateful. I handed her the keys to my 2010 mazda 6 3.7 when she turned 16 a year ago.. I have loved this car and it still looks new and runs smooth and strong. I got myself a 2019 Acura TLX 3.5 around the same time I gave my daughter the mazda. I still drive the mazda now and then to work, im attached to that car still even though my TLX is a nicer ride inside and out.
Never knew that existed right there. Thank u, so much!!! On Gaude!!!
If anybody is going to be Changing or adding transmission fluid to a 2013 Mazda.You'd better go to the dealership and get the right kind. Or else you're gonna ruin your transmission in a couple thousand miles.
@@RegurgiNate84 Not sure where you get your information from but I stand by my statements. I have changed my transmission fluid myself with either Beck/Arnley or Idemitsu Mazda-specific fluids and with over 150,000 miles of flawless operation. If you have to top up your transmission fluid any at all you are having a problem that the fluid won't and can't fix. If the fluid is replaced with either of these two and it fails, the problem is between the seat and the steering wheel and not with the fluid.
@@RichardTait1977 I meant when you drain it without dropping the pan
@@RegurgiNate84 I have never dropped the pan on any transmission that I've changed the fluid on. It's not necessary if you change the fluid frequently. The risk of creating a leak because you have warped the pan, cross threaded or incorrectly torqued a bolt, or got RTV sealant in the pan is too great.
@@RichardTait1977 Good to know.
Dude you seem like a lovely person but nobody wants to watch a dude on youtube trying to unplug a wire for 5 minutes. FFS
@@geargeekpdx3566 Your wrong on both counts, but thanks for watching all the same.
Were is transmission dip stick on 2013 madza 6
I have a video on that: th-cam.com/users/shortswp1dgG50e2Y?si=qna74DbM9NllqoEL
How many watts are the front door bottom speakers?
Unfortunately, I have no idea. What I can tell you is that the amp is 265 Watts with 10 speakers. Whether that means 26.5 watts each or it's split up in done other way remains to be seen. For the record, those speakers are 2 ohm impedance, so you can do with that what you will. Bose is not the most transparent of companies to begin with, and no information about the specs are actually written on the speaker.
@@RichardTait1977 damn. I don't know what replacement speakers to get. I wanted to go aftermarket
@@ramelite Go ahead. I've given you all the info you need. Get some 2 ohm speakers that are rated around 300 watts and are 6.5 inches in diameter. Get the Mazda wiring harness to keep things tidy. You can find everything above on the usual sites for decent money.
you should mention what the service fill oil capacity is.
yeee, thanks a lot
Helpful and accurate, thank you.
Thank you so much for this video! Can you please tell me where you found the glass mirror replacement.
I bought it from tascaparts.com.
Are you able to say if the factory cooler was bypass or connected in series
The cooler that came with the car only had fittings for coolant. It was completely removed and replaced with one that has fittings for both coolant and transmission fluid. The fittings for transmission fluid now feed to an external transmission cooler. So to answer your question, the factory cooler was neither bypassed nor connected in series.
Hey Richard! Can you please share a video on how to uninstall and reinstall a BCM on your Mazda 6 with step by step instructions? I have a 2011 Mazda 6 and the BCM went and now the remote controller won’t work and I need to unlock my car with my key.
Thanks for the confidence in my work. I'm in the process of rebuilding this car to hand over to my daughter. So right now I'm not in a position to remove and replace things just to make a video, if you understand what I mean. I could do a video to point out where the connections and bolts are, but that's as far as I can take it. Time is against me and this project right now so my movements with it have to be pointed.
I finally got a chance to do this job today and your video was a godsend. Thank you & love the accent!
You're welcome and thanks for the compliment!
I am just trying to get the loud machine gun noise to stop can I just remove the fuse for the bose system to stop it?
Go ahead and try that. But what that will do is you will lose functionality of the stereo and Bluetooth as well. If what you want is peace of mind for now, that's a good solution. If you can't find the fuse or if it also takes out another feature that you do want, then just get behind the panel like I show in the video and unplug the amplifier.
Hello. Thanks for the video. Do you have a video where I can see how can you remove the B pillar trim?
Not yet. I have a curtain airbag to replace which might require that it be removed. But the airbag is on back order so I'm stuck. I might jump the gun a bit and do a video on how to remove it, just because you asked. But I have my hands full today. Give me a few.
Thank you@@RichardTait1977 Sure, no problem. It's just because I need to replace the rubber (blackout tape) from that trim. Have successful repair. Kind regards.
Mazda 6 2009 GH has same module configuration or not? Thanks in advance
Yes indeed it does. According to the owner's manual, anyway.
Hi! Thanks for the video. Do you have any update? Is the moog branded wheel bearing still working fine?
You're welcome. No updates on this one, except to say that they have worked flawlessly.
@@RichardTait1977 Great, thank you!
that's the engine oil dipstick, you pull it straight out
No, it's the trans fluid with a 10mm bolt.
你好
Thank you I could not figure out why it would not come down and did not realize the light covers actually hold it up
Ask me how I figured it out 😂
I am able to unscrew the 10-mm bolt from the above the engine, but I`m afraid to not being able to put back the dipstick back after removing it. Is it easy with so little space? If I`m unable to put it back, I don't think it would be a great idea to drive the car. I am baffled at no drawing, photos or videos helping with this. All we have are videos like yours showing a guy removing a dipstick, but we have no visual of the removal itself.
What I'm about to say may hurt your feelings, but it needs to be said. If you have any fear of this procedure you should not attempt it. You clearly do not have the adventurous spirit that working on your own car requires. Removing a 10mm bolt and pulling a plastic stick from a hole and replacing it in the reverse order is neither rocket science nor nuclear engineering. I have zero problem with you calling it quits and leaving your car to the four winds. In fact it is probably better off that way. But if you read the comments, you will find that others have benefited from this video because what people are looking for most of all is the courage to do what they are already prepared to do. Find the courage and stop complaining. Good luck.
You’ll need a 10mm nut to unscrew the bolt.
"promosm"
What is the part the hood latch is connected to. Is that the air inlet duct? Those plastic pieces that hold the 10mm bolts broke and the hood is wonky now :/
That's a bracket that's part of the radiator support. The air intake duct (to the right and just in frame) is bolted to the support. If that bracket has broken then you may have to get creative because I think that is all one piece of composite material.
Had to replace mine not too long ago, got mine right out the junkyard for 12 bucks 😭
That's a great price. Did you do the work yourself?
I did you made it look so easy !
@@ashleyray2agluver That's awesome! I'm glad you are going out there and doing stuff yourself and saving some money in the process. And don't think that we are taking anything off the plate of mechanics. Most of them don't want to do stuff like this anyway, because they wouldn't have the time and probably wouldn't charge much for it. Win-win situation for everybody.
@@RichardTait1977 Now, pretty privilege does play a part when I’m at the junkyard😂!! Sometimes I don’t always have the right tools. I’m always going to find a way to do things myself. I love my first little car, I hope it last for years. Plus I don’t want a car note !!
More challenging task I would like to do include: changing the radio/head unit and updating it to be more modern, like an Apple CarPlay screen ( my car is a base model so it doesn’t come with the fancy bells and whistles), fixing the lock button feature; my car will unlock(sometimes it will act funny unlocking too)but it won’t relock all of the doors unless I do so manually. If I can I would like a key fob, don’t know if it’s possible to do on my car. Lastly , I would like to change the speakers
I just read that the crank is also forged. Is that incorrect?
There is in fact a lot of debate as to whether the L5 has a forged crankshaft, but I have since done some research and based on official documents from Mazda USA, I can confirm that this glorious engine has a forged steel crankshaft "for utmost durability". So yes, that is correct. No surprises there, really, because this engine really has some well-thought out, almost over-engineered features.
Hey, I have a 2009 Mazda 6 and I was wondering where the SD card is because I am having an issue where it says a program cannot be read. Please consult to a dealer. Ever since i put in my new battery
You haven't said where you are from, but this matters, since the North American and World cars are vastly different. Since I am more familiar with the North American cars, I will speak to them. For the 2009 model year, the Mazda6 did not use an SD card for the navigation system. It used a map disc that was inserted into the CD player. Try removing the disc, cleaning it, and reinserting it. If that fails, perhaps the lens of the player needs cleaning. If all of that fails, then perhaps you need a new disc. Frankly, I wouldn't even waste my time. Google Maps is far better than anything any manufacturer puts in a car, updates are frequent, and are free.
Remember dont read it upside-down
Where you from boh
I'm going to wait until you ask your question properly...
How is your start buttom there? What market? Mine is next to the steering column (German spec)
My car is a 2013 North American car. All of them (from 2009 to 2013) with push-button start have the button in this location.
@RichardTait1977 it's literally the same button funny difference, I'd prefer it down there actually 👍Mine is a 2.0L 5 speed auto Wagon, yours? Cuz America got the bigger engines I wonder 🤔
@@Dumpvalve85 The 2G cars for North America and Europe are two different cars. Lots of differences inside and out. Also, if your car is a 2013 it is not a 2G like mine. For Europe the 2013 is a 3G which has the button higher up on the dashboard.
What about the 20?
20? What exactly do you mean?
Have a MZR L5-VE on GH2 Mazda6 Hatch (which Mazda stops making...), love it, still going strong. Very reliable engine, a bit thirsty but I don't mind keeping it for long. Thanks for the video.
You're welcome!
my mazda 6 side mirrors wont /stays fold , i mean they fold to closed, but if i release button they immediately fold open again,do you know what wrong? your are best mechanic ever!
Thanks for the compliment! I'm not sure it's deserved, but I'll take it. 😁. Before I attempt to answer, what year car do you have? I'm almost certain it's not a North American model either, right?
@@RichardTait1977 its GH 2009 EU market model,whit electric folded side mirrors,i think it maybe broken fuse cause it,its not big issue but still tight places it is good to have:)
@@chimai001 From what I understand the button to fold those mirrors is off you press it the button stays in. When you press it again, the button comes back up. If you are saying that when you press the button in to close the mirrors and it doesn't stay in, then it sounds like you have a problem with the mechanical action of the switch itself. It might be something as simple as dissembling the switch and cleaning and greasing the internals. Switches inherently burn a bit every time they are used and after a while things get messy inside. Alternatively, you could see if you could find a replacement (used, new OEM, or new aftermarket).
@@RichardTait1977 yes press button,thanks for you answer:) i take a look,maybe it is button issue indeed!
@@chimai001 The way I see it, it's already not working right, so how much worse can I make it? 🤣
So does disconnecting the switch work or no ?
Unfortunately not. It's still a mystery what causes the alarm to go off sporadically. I've reached out to Mazda USA and they say they aren't aware of this issue with the 2G. Yet, most 2G owners do. They were, however, willing to look at the car, which is a good thing. But I wasn't able to take them up on it because the car was in that wreck. It's being fixed as we speak so when it's done I'll take it in for them to look around in. Hopefully this will benefit the entire Mazda6 community. Fingers crossed.
Hi Richard, is the variable length intake and tumbler the same system? Are there 2 set of flaps in the intaje manifold? I noticed there are 2 vacuum runner solenoid valves and was wondering why. I recently stumbled upon this "flap of death" video where it said on some Ford with the 2L engine the flaps and metal rods that connects the flap would break and destroy the engine. And after searching a number of Ford owners would "delete the flap" to prevent this. Is this less of an issue on Mazda? I have a Ford 2L now I am really worried.
Lots of questions. Let me see if I can answer them. 1. The variable intake length system is called Variable Induction System (VIS) by Mazda. The tumble system uses Tumble Swirl Control Valves (TSCV). These systems are different and actuated by different solenoids. Basically, VIS changes the length of the intake manifold, whereas TSCV controls the speed of the air going through the intake manifold. 2. The "flap of death" issue is less common in Mazdas. In fact, I have never heard of any such problem occurring with the 2.5L L5. However, from what I gather, the problem was sorted by Ford early in the production run and the affected cars have a yellow flap assemblies. Additionally, those assemblies would make noise before they gave way, giving you enough time to be able to make the relatively easy repairs. This is something that can be done by any DIYer and is not complicated at all. Don't worry. Just know that if you start to get a ticking sound from the intake, then it is time to act.
@@RichardTait1977 Thank you for taking the time to answer my questions. That's very reassuring, thank you very much, you have a great day.
@@roycai8895 No problem.
Nice little project to keep you busy haha Glad to see you're fixing it up!!
Yes indeed. This is the first time I've ever tackled something like this and so far it's a good feeling.
Its nice to see that you didnt scrap the car and trying fix it:) yea it maybe not finacially worth it,but emotionally it has indeed! good memories in car:) Does the insurance cover the costs?
The insurance company deemed it a total loss and cut me a cheque. However, fixing it myself is going to work out much cheaper because I have/will be doing some of the work myself and will get used parts where and when I can. So thus far it is financially worth it.
Interestingly the blind spot monitoring is not part of the mirror as far as am aware. The 2 module sensors are located under lights in rear bumper and lights in tweeter cover. Well in uk model anyways
The mirror is a part of the blind spot monitoring system. The sensors may not be in the mirror, but the display for the system is. Without that specific mirror, the system will not work. As it stands, this mirror retains functionality from the adjustment pad on the door, but it has no glass heater, no BSM display, no automatic dimming, no indicator, and it does not fold at all...not even manually. It is really a retrograde item on the car, but I give thanks because driving a car without a driver's side mirror is suicide.
@@RichardTait1977 am integrated because I believe the UK system for bsm is different. Do you have a rvm light on tweeter panel? Or is the light on the mirror unit? Regards
@@jordanb2769 There is an LED icon that is inside the mirror glass itself. No lights on the teeter cover. World cars and North American cars are so different I'm wondering why Mazda even called the two cars 6s.
And the filter? Bad work😢
This is a transmission fluid change, not a fluid and filter change video. As the name CLEARLY states. This is a drain-and-fill procedure which is a perfectly accepted and endorsed method of servicing a transmission. The filter does not need to be changed if regular drain-and-fills are done. I'm not here to debate this with you, however. If you want a debate, first watch respected mechanics like Scotty Kilmer who has been a mechanic for over 60 years and see what he says. When you have done that, come back here and make your comment against what I have done.
Also what does that sensor control?
It tells the computer when the bonnet is open. It's part of the security system.
What inch is the 10mm bolts?
Are you asking what 10mm is in inches or are you asking how long the bolts are?
@@RichardTait1977 yes
@@ltaylor6433 Which one?
@@RichardTait1977 the bolts in the front holding latch. You said it was 10mm in the video what's the length of those two bolts?
@@ltaylor6433 1 inch. 1.0680 to be exact. For the metric people, 27mm.
Do you need extended licence for this as mine only shows reset modules
Yes, you do need the extended licence. It's pretty reasonably priced though.
@@RichardTait1977is that different from the 2 month extended license (free)
@@joshymcdaniel9233 You get the same functionality as the paid licence, but just for a shorter time.
@@RichardTait1977 that’s what I was thinking but everything changes so much now days you never know .. haha Thanks for fast reply!
@@joshymcdaniel9233 FORScan does change their licences a bit. When I gotta installed it, a lifetime licence was $20. Then they changed to 3 year. And now 1 year. I'm glad they are still around, though. The guys that designed it are Russians and have come under pressure recently because of the war.
Hi brother, thank's for your videos, i have a smooth beep sound while im listening to music, do you know if that's an amp problem?
I've never heard of the amp responsible for something like that. Are you sure the sound is coming from the speakers?
@@RichardTait1977 yes, The sound is always there when the radio is on, it's a beep sound behind the music
@@luisfelipemartinruiz7842 This may sound strange, but try the dimmer switch. Adjust the dimmer switch all the way bright. See if this helps