วีดีโอ

This washing machine is made by whirlpool

U don't need take shop push in tensioners use car jack 😆 and u don't use hammer for harmonic balancer u just get longer bolt use push in

Did you or how can you do a transmission oil change?????? Our selfs???

Thank you bro 💯

Sooo if I didn’t get that thin metal gasket on there what will happen? I almost gave up and set the mf on fire and finally got it and then seen that gasket on the ground. I can’t do that again no way in hell

Refrigerant tape did you use? I'm having the hardest time in the world getting it sealed correctly.

This is a whirlpool built machine from around 2007 built in benton harbor. On some of these you can turn the timer backwards when it’s pushed in to set your desired cycle but never turn it backwards

I never take off mainfold when i change my egr same car😎

Thanks for the video. I took my car in for a tune up and my car started to stall and or run funky so I checked out the job and sure enough the damn seal was messed up so on the side of the road I too used some of that self sealing rubber tape wrapped it around the valve tube and manifold and it worked like a charm. I was back on the road in no time. Glad to see I’m not the only one that had that idea. 👍🏼

This part goes to this part to this thing, 😬🤣

I had some loss of power in my Charger, the 2 seals on the egr tube were bad so I replaced both but even with the new ones on it doesn't seal right in the Plenum. There wasn't really much of a difference in how the car runs after changing the seals. Could it be something else?

Sounds like they are making it harder than it has to be. The u0121 is abs not communicating and next u would wanna see what other modules it’s not talking to. If it’s multiple chances are the can wiring or a bad module or a fuse has blown powering module definitely not 8k to diag. Sounds like a tech who didn’t want to work on a car above his level

What was it

Great tip on that little screw!! Thanks

If youre going to be a selfmade movie star. You should invest in the right equipment. If I were a rookie trying to follow your lead. The car would end up in a crusher. Because it would never run again... Lol

I deleted my EGR valve.

غير مناسب للمبتدئين .

I appreciate your video sir!

I have this washer and watched this video trying to figure out how to open it up. I tried this method for about half an hour and then gave up and called a repair man. The repair man popped it open in one minute. Here's what you do. (As best as I can remember. It was a few weeks ago.) I'll call "the console" the part of the washer with all the knobs on it. 1. Stand facing the washer. 2. Slide a putty knife or some other flat metal object under the console (between the console and the top of the washer) on the left front. It will release a latch. 3. Do the same on the right front. It will release a second latch. 4. The console will swing up and back, hinging on the back of the washer. 5. Each latch will have a metal hinge type thing that you remove, allowing the console to swing all the way back. 6. Now the whole metal body cover of the washer can be lifted away, so that you're left with the washer drum and machinery still attached to the back that has all the cords.

At 3:25 you said there's no way to check the fuel pump but actually yes there is, you check the fuel pump by checking the fuel pressure at the fuel rail. Listen People. Don't believe everything you hear or see on TH-cam. There's real Mechanics out here and then there's these type. Just saying

Can that cause smoke to come from the front of the engine I replaced that egr tube seal and pcv valve and valve cover gaskets now it’s smoking from the front and the lightning bolt sign come on dash and shuts car off

that focking grommet at the end of the EGR valve is such a royal pain in the ass unless you take the whole plastic cover by the windshield wiper motors!! i installed a brand new intake manifold and low and behold the stupid ass grommet was busted and i could not replace it on the fly and i was livid with the idiotic engineering behind this car. real smart dodge, real smart..

It's just one pump the other side is a feeder point/regulator,filter and another place to gauge the fuel level..

Appreciate the info. Fa real!

Wonder what SCOTTY KILMER would say about this

So the blue thing is only a dust ring there is a second o ring that stops vacuum leak

Can anybody explain what the plastic little balls are for? I changed the transmission oil and three of them came out,and I disconnected the panel connected to the filter,and that's how they came out.Does anyone know where I should put them?

What is the part called under website??

Pretty neat in full view you can see where the timing belt notch plastics chipped off that means the belt is stretched.

Wow u1120 and u1110 2008 town and country wow

Take the harmonic balancer bolt in to a hardware store- get one that's an inch longer and use it to drive the harmonic balancer on a little - till the original bolt can catch

I have the same noise on my 300c 2005 and a mechanic thinks it's the water pump pulley , I dont think it is . It probably is the alternator...

Or just let Dodge/Chrysler change the entire tank, pump, regulator for free, lifetime replacement. Reimbursement also if already done previous to recall notice.

I own a 2005 Dodge Grand Caravan SXT 3.8L. Worst Van I have ever owned. I have to pull the IOD fuse for the locks to work and the door to open. Now ABS light is on, and emission code 0420. I have owned older vans like the Voyager without problems but this 2005 is the worst.

Was that the egr?

That’s a pretty expensive fix close to 1000 bucks knnparts alone from mopar my fuel pump has went and I’m going to just replace the drivers side in my 5.7 Hemi

Damn so you should do both eh

2 separate fuel tanks.

How many you need

Thanks so much for this video

Thank you so so much man you really help me man i have a mágnum 2006 and everything its the same i bought it frome a guy and it had the egr pipe cut off

Sorry if it sounded like I contradicted myself...its been a day talking about with experts. So here goes a $30,000 car right down the Crapper for me. It still runs great but tends to code with PO300s about once a week. So this car has no future period is what I should have said.

why pull the crank case?

Did this cause your p0300 misfire code ??? If so I replaced my pumps once now they whine louder than ever might have bad ones again? Mines an 06 with almost 200k on the dash

I have the p0700 and u0100 codes appearing in my 06 Dodge Charger rt, by any chance was your car shutting off? Also did the new part solve the problem?

Is it guaranteed that this code means this repair? Have this code on my 2008 Chrysler Sebring 2.4l 4cyl.

Sorry about the camera being all over the place but filming with one hand and trying work with the other...

Sorry about the shaky camera...using one hand to film and the other to work...

So Sorry about the wobbly video taping...one hand you know to hold the camera and the other hand to try to get things done.