วีดีโอ

Thank you! You made assembly a breeze!

You don't need to cut fins. Just bend them. they comes off easy.

Do you have to use a crescent wrench? Or can you just tighten the bolts by hand?

Not gonna lie, shouldn't have posted the vid😂 Thats horrible my guy

With using those anchors, what weight TV do you think would be pushing it? Think a 50 lb TV is OK? Thanks!

He's pulling his caulk out

Where's the insulation ? And where's the humidity black sheets that are supposed to be mounted before the boards?

This is how it's done 😊

Thank you

Thank you for the video!! what size cabinet screws did you use?

Does it block the airflow ?

Nice, thank you so much!

This guy doesn’t look like he does a lot of caulking 🤔

Why does nobody ever show the dang whole floor at the end when they're done!! Lol damn it

Much better tips than most videos I've watched!

Straight to the point and nothing fancy ... Thank you!

@2MinuteHowTo I just need to lift mine up so that I can re-glue and reapply laminate tile that has started to raise due to water seeping in from the carpet when I steam cleaned it because the installers did not go around the edges of the tile with silicone caulk. I just want to gently pry it back and leave it on the carpet and then put it back down after I finish re-gluing the tiles. Can you give me a suggestion for removing it without causing any damage so that I can put it back down again?

Thank you

Straight to the point, no Messing around. Thank you as this was very helpful to me. 👍

The way I used a construction window as a replacement window, by after the measurements, I just got a smaller. measurement for the width, then add the measurement for each 2x4 on each side and then measure the height, then add measurement for one 2x4 for the bottom. Then i used the two 2x4 and one 2x4 and frame the new window. Then, put the new frame in the old frame and the space outside the new frame, fill that area in with 2x4s, and pressure treated plywood on the outside and paint it. Then un-screw the new window frame and put new window in new frame screw the finn in new frame then I slide new in it spot and hold in place while someone screw the new frame into 2x4's around the new frame. Then insulation the old section. Then drywall inside and paint.

Holding the caulk gun and a phone at the same time must have been hell, but this was super helpful dude thank you!

I have a lot of experience in tiles. Can I get to know you?

What about using a table saw with a finished blade?! I have to putt up 2k sq ft of this bad boy

Do you need a board in the back to keep them level.

Thanks TH-cam dad !

These don't tighten, any wind it's gone

Ya saves money but as soon as caulking or whatever he used gona leak like crazy

Those tiles are gorgeous. Would you please share the info on them?❤

Dust mask and goggles for dry cut

Do you need to scrape the old silicon or you just apply over it?

Thanks! I'm going to do MY windows with Caulk because I can't afford getting new windows put in!!😊

I know you’re not gonna see that but come on

What type of screws are these?

Are a conytractor shit job you must be a real pig to work

He didn’t mention that the old one was mounted wrong then proceeded to mount the new one wrong. 😐

uh yeahhhhh…. I am guessing that was 1/4” not 1/2”….

Attaching a wall mount to plywood

Ty my family needs a reminder to this 😂

Thank you for this!

All right ok

New homeowner, single woman, and new to diy- THANK YOU for this video!

Taking forever 😂😂😂😂

Bro, thank you. Finally someone covered this issue. I'm new to the scene and I couldn't figure out if this was a camera/lens issue, or common to all cameras. It took me forever to finally come to this video. I guess I'll have to either switch to manual focus or just cut out the noise in post, which isn't the worst.

Watching this in 2024 thank you !!

But you didn't show the Masonite board you put down on the floor

Horrible job

I personally would wrap the window around the outside with the foam they offer too.

Hello, thanks for this. If you are resealing do you need to remove the old silicone? Thanks so much

A set of ratchet spanners are handy and quicker.

show us a CORNER cabinet .. those angles...