วีดีโอ

Hi there. That could be a number of things, however we are Gema distributors in the Pacific Northwest only, so I'm happy to help if you're in our territory, otherwise I'm not sure I can help you. To find a distributor that serves your area, check here: www.gemapowdercoating.com/en/contact-us/local-distributors

Great question! You can find the step-by-step instructions to change your OptiFlex Pro’s application on page 33-34 of the corresponding manual found here: www.gemapowdercoating.com/fileadmin/documents/User_Manuals/English/Equipment_and_Controls/Gun_Controls/OptiStar-CG21-en.pdf?hash=1715870895 Basically, after moving the powder pump from the box feeder to the top of your hopper, you’ll hold the lower left button on the controls screen for 5 seconds until the screen changes to display the P00 system parameters. Next, you’ll toggle the application to ‘0’ / ‘F’ for fluidized hopper. Hope this helps!

It depends on the model and the distributor, so contact your local distributor on this one. We serve the Pacific Northwest in the United States, other distributors can be located here: www.gemapowdercoating.com/en/contact-us/local-distributors

Simon - Thank you for the question. To engage PCC mode, you'll need to create a custom program. To create a custom program, use the ‘< P >’ buttons on the lower right of the screen to toggle between programs P1 through P20. You can create up to 20 custom programs on this unit. The create a custom program with PCC mode, you'll need to set your microamp setting at 10 or below. Let us know if you have any more questions, and we’ll be happy to help. You can always call us at 503-222-9741

Hi there! We cannot post the cost publicly due to Gema's distributor restrictions. Please send an email to info@finishing.tech and we'll be very glad to get back to you (NOTE: we are only able to sell Gema parts and equipment within our territory here in the Pacific NW).

Hi, George. The system *is* 110v, there aren't any other options as far as we're aware.

Hi there. It isn't really the pressure pot that will determine what size compressor you need, but rather the spray gun you're using. The pressure pot itself uses pressure-up to 15psi, which will move most fluids (get a pressure upgrade kit if you need more)-so really any compressor can handle the tank. So, again, depending on the type/style of air-spray gun you're using is the more relevant factor.

@@finishingtechnologiesso a 4GAL 2HP Twin Compressor would be enough?

​@@Unseeable.. ...to run the tank by itself? Yes it would. If you're running both the pressure tank AND a spray gun (or much of anything else), no.

@@finishingtechnologies thank you for the feedback. I was thinking of going that route (use the compressor to power both the pot and the gun) but now don’t know what to do

@@Unseeable.. Yes, that compressor is unlikely to be large enough to run the spray gun. While it'll pressurize the pot, your gun will likely need much more air. Look for the "CFM" that your gun consumes (this is usually in the air-cap specs). You'll need a compressor that can put out at least that much, though we recommend *more* than it consumes so you're not running your compressor at its max constantly. Good luck!

Thank you! Really appreciate the feedback.

Hi there. We probably won't be producing any further videos on this equipment unfortunately, however you might be interested in this handy guide (.pdf download) specifically about application tricks with the Process-2: tinyurl.com/bdd276rm

Hi there! That is a Wagner "Jaguar" 55:1 industrial liquid paint pump. Let us know if you need more info. ;)

We appreciate your feedback! Gema makes the best powder equipment on the market. We stand behind their equipment with our well-trained technicians who want to empower end users by sharing what we know, and giving great service.

Hi there. Thanks for your comment. While there are some booths that exist which can do this, most of the time (depends on your local ordinances here) you cannot recirculate back to the area unless you are spraying something like a *waterbase* adhesive or paint. Solvent-based materials are almost certainly not going to be allowed in such a system. Check with your paint manufacturer and local rules as to what may be recommend. Normally, we do NOT recommend this unless a new booth/filter system is implemented. Give us a call if you'd like further help here.

Hi, Muhammad: we aren't a "factory" here at FinTech. We're integrators/distributors located in Portland, OR. If you mean that you're interested in the GEMA factory, they're actually located in Switzerland and have a main distribution hub that is located in Indianapolis.

can give information regarding to code error H91 short solution mybe

Gema is not owned by ITW any longer, actually. They're now just Gema, Inc. Some of the older equipment may still reflect the "ITW" monicker, as Gema was once owned by ITW but that is no longer the case.

Glad it was helpful!

So glad it was helpful. Thanks for the feedback.