วีดีโอ

Thank you so much!!!!

I have a 222 which every part is on correctly as in this video. Adjusted correctly. Mower belt able to move by hand easily but will not grab when engaged. ???

I have never seen an adjustable like that in my life. Much thinner which is nice.

Great video! Thank you. Where did you source this new clutch assembly? Mine just failed and I am in search of a repair. Thank you.

super helpful. I have had this thing apart several times and I think this is the first time it has gone back together properly in years!

Thank you! Best description I have found! It works!!

Thanks so much. I have the owners manual that does not show how the cams are offset. Neither does the parts manual with the picture how the assembly is put together.

bless you, this tractor is ruining my life 😂

Thanks Jim!

Litterally the only thing i needed to know was how to remove the grab handle and its skipped over

Amazing Friend, I have been fighting with this and losing lol my mower blades wont turn off. I will go fix now thank you for the video

Mission accomplished , you coughed on everyone

Great step by step instructions Manual does not do a very good job explaining

awesome. thanks. I took mine apart making sure I stacked everything in the right order and then managed to knock the stack over. so I had things in the wrong order.

Thanks again, great videos!

Thanks for the video and sharing your knowledge it has been very helpful!

This is a little bit late but I’ve been having a hard time getting the pillars to pop off, any tips?

Thanks I have tape & super glue! I'm thinking about getting some thumb tacks ! Wish me luck + cold beer brother

Amazing!!!! Thank you. This is an awesome “how to” video!

Putting a snow blower on my case Ingersoll 224

Thank you

Dealing with some p2177/p2179 Lean codes on my 03/540.. What a PITA this has been. checking to do this after I smoke test it..

Thanks a big help. The previous person didn't have it right.

Awesome video I've got a replacement my bearing on my 448

How tight should engagement feel on the clutch lever? I followed as best I could after getting the parts that were missing from mine and I have about .005 gap, which is within tolerance from the manual, but my engagement is quite tight. It looks like the spring washers compress really nice, though, so maybe it's fine. It's a good firm pull to engage the clutch on mine. See an issue with that?

Just replace the bearings in mine, and would have never figured out adjustment. Thanks a bunch 👍

Life saver, thanx a lot buddy!

Thanks a big help

When I start tightening the fan but the back plate pushes against the clutch plate. Any idea?

....sadly, ... I broke my fan!!

Looked for these instructions for a long time.

From lords heards Dairy thank u

My dream car🤧

Thanks for making this video. I've had this apart before but can never remember quite how it goes back together. With over 41K views, you know that you've helped thousands of people. A big thank you from the mountains of western Maine. I use the PTO for my snowcaster and we generally have 4.5 - 6' of snow on the ground for the duration of winter every year. We depend on the Case to move that snow. Thanks again!

Hey, Mr. Steve I need a new motor for my 446 Case b43g can you help me out with anything or advice I’m in ky not to far away lol please

I used high heat epoxy / resin. The bond when u spray only lasts so long till u have the same problem later on

Nice Job. This was how my Dads 1988 was. My 1992 sags in the back corners. I'm going to just remove mine.

Holy hell finally got everything

If I tighten the front boot to much will that cause the PTO lever plate to not move very much?

Clutch was on wrong no PTO engagement. I followed your video now when I went to turn it on and I have no power? Any suggestions

Awesome video!!! Just bought a 224 n was wondering what that clutch was for

Thank You So Much !!! This Is By Far The Most Helpful Video on TH-cam !!! You have saved Countless people Hours of "Pain & Suffering" !!!!!

Just what I was looking for... Thanks 👍😁

I’m a Carpenter not a mechanic but I think this will help

thanks

great instructional video... but i got motion sickness whatchng it... good job though

This was an incredible help to me; thank you.

I own a Case

Cool old tractor , but in Canada we wouldn't call that snow, that's just a little white dust. Lol

Great video, thx!!!