วีดีโอ

Hello! In this video you mentioned that you have a wood mizer lt40. Would like to hear your comparison between wood mizer and mobile dimension as far as cutting 2x4 or 2x6s. Seems that you run both for a while that's why your opinion would be valuable. Thanks in advance. Ps. Just left a message on your answering machine. Looking forward to hear or see a video

I believe it would hold a lot better with the screws in the valley, the same as you would do with a tin roof with screws! I like the way you did your roof! I've put down a lot of tin roofs, but never a poly one.

Who owns the trees you’re cutting??

THats badass dude!!

You could make a shelter with that bark.

Good content!! love the boat use thats something i would do.

We appreciate the fact that you took the time to share the whales with us!

So cute my dogs birthday is today❤

what areas can I do this, i live in kketchikan

Thanks for sharing your install! Takes a lot of effort to document and share, so I appreciate it! As I've just done an install (DIY) some notes for anyone else installing Palram SunTuff polycarbonate sheets: - Minimum slope is 1.5" over 12" - Purlin spacing can be from 16" up to 36" depending on required load support. Always use sheet of plywood across at least 3 support members when traversing the roof. - Use appropriate flashing (side ridge, wall connector, counter, etc) at connection points - Use, at least, horizontal closure strips to allow for screwing roof sheets at the crown of ribs (ridges/hills) rather than in the valleys which can leak - Screws should be placed along purlins at the crown of every other rib (and at every rib if in high wind area) - Always make sure to pre-drill all screw holes using 1/4" bit. This hole is actually wider than shaft of screws and intentionally allows for sheet expansion/contraction. - Place EPDM screws (e.g. WoodTite) using a screw gun (e.g. like for drywall) or a drill with low clutch setting. Do not use an impact driver! Screw and its washer should be snug, not compressed at all. - For additional water tightness, only specific sealant (polycarbonate compatible) may be used along connection points of sheets. Manufacturer recommends only 100% silicon sealants as other sealants/adhesives often contain a solvent that may damage the polycarbonate sheets. For white roofs, I have used Henry's 884 Tropi-Cool white 100% silicon roof sealant caulk, but for my project with clear sheets, I'm using GE Supreme Silicone Caulk Window and Door Sealant Clear (model: 2814816) Ref: images.thdstatic.com/catalog/pdfImages/0f/0f8191b5-f9ec-4080-bc12-84dc04df3bbd.pdf

Hey Sterling, just found your channel great videos! Hi from Tucson AZ!

My stevens 22/410, has the barrel select on the hammer. Does anyone know why..

very nice pile of logs !

My dad had the same windshield wipers in his Mack, back about the same vintage as that truck.

You screwed the polycarbonate panels on the valley?? that will leak prematurely. Why you did not use horizontal closure strip? that way you can screw the panel on the peak.

Is your #4 a BSA?

Careful dude ...! Beautiful tree!

What is the height of the aframe?

It takes balls to throw your work up on the internet for the internet to critique. You learn a lot that way though.

This place looks like heaven

Light weight Shotgun and 3" magnum tend to bark! Lol Great video

Excellent machine of how many hp is the engine can you give me the reference please

How did you not drag the bottom of that boat on them rocks looked so shallow especially when ya said 6 inches of water.

Beautiful job mate. Excellent

Awesome stuff mate!

Next time extend the top poles, then put the rain fly on and extend the bottom poles.

enjoy your beautiful place in the garden of edan🙏💕

Does he ever stop talking ?????? I'm sure most of us have seen metal roofing installed more then once.

How long did you own this land ? How big was it ? This house looks so nice with an amazing water front , ❤you did such a great job, your daughter is too cute 🥰

Hello from Northern Ontario. Found your channel in our feed. We have 50 acres and are off grid and are building smaller A-Frames and bunkies. I think your channel will be helpful for us so we have subbed! Come stop by our channel if you have time. We always have something different going on! Cheers! ✌️🇨🇦🇺🇸

Lose the kids when you are trying to sell a tiny house, it is distracting with her screaming & trying to get attention!

Too dark. Can't see anything

Were did you get the saw teeth sharpener.

I have trouble finding two belts that match perfectly let alone six.

What's the purpose of the wedge.

Do you buy the belts from the factory there in Troutdale.

I agree with the music get rid of it

Music too loud

too overdone on the music

Love the video thank you guys. Paul Townsend from Eastern Oregon model 127 just like yours except it's pull rope start.

Can you stop the feed in the middle of the cut.

This milll is built in Troutdale Oregon they have everything you need for that thing.

Absolutely love the video and the information thank you. I was hired to work on a model 127 the engine it was really hard to start it's a pull rope so that engine's got to be perfect to get a running. They tell me in the winter time it's almost impossible to pull the rope when it's cold I haven't seen that yet but that's what they say.

Why’d you use screws instead of nails for the siding?

small cable skidder

What part of southeast you in?

I have mentioned before about the hight of your stumps and that's what happens plus landowners would not be happy about tonnage loss with high stump being left but still like the channel.

Looks like you lucked out on that track!!!

Thanks for videos. Helped a ton with my own build.

Would the 9.9 motor be sufficient for 2 adults on a 11 foot ? How's the power? Thanks