วีดีโอ

Hello bud I'm so sorry it's taken me so long to post these videos up. I am juggling far too many projects atm it's difficult finding the time getting them all done. KWC do some awesome plinkers. Hopefully, you are very happy with your purchase and enjoy may hours plinking. 😃

Hello bud Thank you for the nice comment. I'm glad the video has helped you. I will redo it at some point as the lighting and audio aren't great. You could also try a thicker gage spring and do away with the washers. Just be careful to keep the power output well within your countrys power limits Happy plinking 🙂

Here in Spain the limit is 24 Joules, not a problem with these Co2 pistols.​@@bingobango7734

@josefranciscomarincobo1021 Hello buddy I also have the gen 3 glock 17 that one doesn't allow you to remove the top slide unless you disassemble it. This gen 4 glock 17 will allow you to remove the top slide to adjust the hop up on the barrel if memory serves me correctly they did 2 versions one with the hop up and 1 without but I'm not 100% sure on that as I haven't seen one myself this information came from an air pistol forum. Both the glock 17 gen 3 and gen 4 are great little pistols my favourite out of the 2 would be this gen 4 in the video Purley because it allows you to semi field strip the top slide I hope this help 😀

@Zbigu Hello buddy Is this the umarex glock 17 gen 3 you are talking about or a higher model I can't find this one online also did you replace the co2 bulb seal ? If not try a few drops of pellgun oil on it and leave for 24 hours soaking I believe you can also use something like a car automatic transmission oil but don't take my word on that as gospel as I only use pellgun on mine

@@bingobango7734 Hello, thanks for quick answer. My Glock is Umarex Glock 17 gen 4. Exactly the same like on this video. There is output valve with one oring 6x1mm and I have replaced this and lubricate with silicone oil etc, all done and is leaking. I think the internal spring is too weak or the pin is not blocking the CO2 correctly. This Pin is just metal cone going inside teflon washer and there is only one oring sealing the mag. I tryied different Orings, thicker and no results. I think this valve is broken because the oring is new. I screw it quite hard (maybe too much?). This valve is short overal c.a. 16 mm and is very difficult to find. The original price is very high and therefore I consider new mag but different producer, but I am not sure which will be good.

@Zbigu Ah ok sorry just wasn't familiar with that number for it .are you using co2 rated o rings ? Normal ones such as plumbing ones will allow the co2 through and not work properly they can also split. it does sound more like the white bulb seal could be the issue especially if you are possibly over tightening it. it's the flat white looking washer sitting over the piercing nozzle. Try removing from the magazine and soaking in pellgun oil or atf oil over night and flipping it over before reinstalling it.also a small thin washer underneath might help. Then say 3-4 wraps of ptfe tape on the threads of the main locking nut that holds it all in the magazine. Regarding other magazines I'm afraid I really couldn't answer as I've not yet tried any you may have some luck with airsoft parts for it some airgun forums may also be able to answer the other brands of magazines question for you I believe some people have been able to use extended mags for them

@0XAN Hello buddy I'm getting roughly 8 magazines worth of shots from 1 Co2 bulb with the power starting to decrease on the last 3 magazines but the type of ammo you use may cause different results. With increasing the power a longer barrel should increase the power very slightly but you would have to take into consideration the maximum barrel length formula. Also things such as temperature, humidity and if your shooting indoors or outside will have an impact on power. If you are in the UK please take into consideration the maximum power regulations by uk law. I hope this helps buddy and happy plinking.

@petervick4775 Hello buddy you are probably right with my under leaver it's a few pins to tap out and a couple of screws

@mustanggt35r44 Hello buddy I'm so sorry it looks like I've somehow missed this comment I'm pleased this video will help and good luck with your build 😀

@TheBionicGolfer Hello buddy, this was also one of my very first air pistols as a youngster. They fire pellets, darts, and corks but like you mentioned they are not very accurate you probably had more chance of hitting the target by throwing it at them. If I remember correctly somewhere like argos or woolworths used to sell them back in the 80s.

Hello Have you completely disassembled it cleaned and lubed everything ? Sometimes a good clean and lubrication is all that's needed. Next check the front plastic barrel retaining pin is the correct one for example if you stripped it all down for cleaning did you fit the correct pins if it's a thinner one it could be slipping out and jamming the top slide also check that the hole isn't warped can you wiggle that barrel section ? Next check the silver trigger bar on the right is it all sitting flush and moving freely make sure as you pull the trigger nothing is causing it to kick out. I would also check the top slide it's possible the top slide may have been squeezed in and bent a little.

I will have to take a look buddy in the UK we can't go over certain power restrictions.

Hello thanks for the comment buddy really appreciate it the next one I'm doing is on a colt 1911 by gletcher I will need to get hold of a single action colt

@@bingobango7734 Hi my friend, awesome awesome :) cannot wait. I must say you are very talented with feet on the ground with a very good logical mind. I understand theses toys are getting expensive and you cannot (like me) buy everything you would like but man if i win lottery one day i will send you a lots of money for you to get the ones you want and make videos on them. All in All please try to make more videos like that and ...maybe even start something new on your channel with test shootings and before/after mods or something related to airguns , every one would like that ! have a nice one Bingobango , will wait for your next video :)

Hi buddy Sorry for the late reply thank you so so much for the kind kind comments it really does mean a lot I'm hoping to get back at it all over this upcoming year the colt 1911 will be my next video.

@@bingobango7734 will wait for this. just dont forget to title your video : KWC CYBERGUN GLETCHER COLT 1911 Co2 DISASSEMBLY video in order to reach most people and get thumbs up as possible ;)

@Dan-Commando That's a great idea buddy only trouble is the 3 1911s I have are all completely different internally but those would each have transferable disassembly methods. So maybe find which brands cover the same build of each one and add that into the title 🤔

Hello thank you i appreciate it bud how do you find the 19s I've got a gen 3 and gen 4 glock 17 out of the 2 I'd have to say the gen 4 is my favourite.

Hi many thanks I appreciate it

Hello Unfortunately I've not taken the hammer assembly apart myself yet as I haven't had an issue with mine but it sounds like you may possibly have one of the springs situated in a wrong location or may even need to flip it over. I would disassemble again and double check the springs are all situated correctly. If you google the exploded diagrams hopefully you will see where everything sits when put back together. Good luck with it and please let us know if you managed to resolve this issue.

Hello sorry to hear that buddy it could be a couple bits causing it I will try and get a short video put up over the weekend to try and help you out

Hello the new video is live now hopefully it covers the issue you are experiencing and helps resolve it.

Hello are you meaning the recoil spring guides ? Check out bagnall and kirkwood part L26

Hello if it's the tool I used to undo the valve nut I made them from an old socket just cut and file

Hello sorry for the late reply yes this is a blowback air pistol

@@bingobango7734 thank you so much for your answer!

Hello sorry for the late reply I have been out of action for some time. It could be a number of issues firstly does it sound like anything is leaking it may just need a few drops of oil on the seals or even replacing them. Does the valve piercing pin have any damage does the opening look restricted? And inside the valve is a mesh washer this may be clogged and need a clean. I would strip the valve and clean everything while checking for damage it would be an idea to purchase the valve seals in advance so you can swap out if needed. Let us know what you find good luck with it all.

@@bingobango7734 Hi thanks for the reply, no leaks, I left the co2 in for a week and no loss. I will do as suggested and take the valve apart it’s probably clogged up.

@GSwton ok so no leaks which is good I wouldn't leave the co2 bulbs in when not using the pistol as this can damage the seals. Go careful trying to remove the mesh washer sometimes it will just drop out freely and other times it needs to be shaken out. Good luck I hope you can get it running again let us know what you find.

Hello sorry for the late reply I have been out of action for some time. Thank you for your kind comment I really appreciate it 😊

Hello sorry for the late reply I have been out of action for some time. Thank you I appreciate it buddy.

Hello sorry for the late reply I have been out of action for some time. OK have you cleaned and oiled it as sometimes this is all that's needed. Then I would look at the sears for any damage if you check out my skiff video I do a repair on one that was for locking the mag in place. I would check around the hopper screw and top slide make sure no rough parts are sticking out causing a jam. Let us know what you find and I hope you can get it sorted 👍

Hello sorry for the late reply I have been out of action for some time. Thank you so much I really appreciate the kind comments I'm glad this video is helpful.

Hello sorry for the late reply I have been out of action for some time. I would like to help but really only make these videos to try and help people repair themselves. I really wouldn't feel comfortable tinkering with something that wasn't mine sorry buddy but maybe we could figure out how to get your one repaired.

@@bingobango7734 thanks for replying let me know if you change your your mind at this point I don’t know what to do peace out could pay

What issues are you experiencing with your model buddy.

@@bingobango7734 i got it broken tbh it was jammed I’m not a expert like you wouldn’t know where to start I will give it another look maybe try and dissemble it

@lionmoet5841 Ahh OK double check the top slide isn't bent like mine was its a very thin alloy and possible to dent inwards by just squeezing on hard when pulling back another possible reason could be a jammed sear or loose bb

Hello sorry for the late reply I have been out of action for some time. I did find some similar information online some have the screw and others don't but if memory serves me correctly it should still have the threaded hole for one and possibly a airsoft one might fit but I haven't tried this.

Umarex removed the hop up system of new made air pistols. So stupid decision. I added a little bit cardboard on the hop up rubber, so it push down the rubber give the BBs a spin.

Hello sorry for the late reply I have been out of action for some time. If you have a version like mine with the hop up dail this back and then dail back in testing after a few shots. I'd look at the end of the barrel for any damage or if it needs cleaning. Also does it sound like anything is leaking?

Hello sorry for the late reply I have been out of action for some time. It is quite straightforward as the parts just have to be unscrewed. The o rings and seals a chap on ebay was selling. Make sure the o ring is suitable for co2. I will be doing a video when back at it as mine has started to leak . you can buy tools for the job or even use a large flat head screwdriver but be careful not to damage the co2 piecing pin or any threads. Good luck with your repair buddy 👍

Hello sorry for the late reply I have been out of action for some time. You can try a few drops of pellgun oil on the seals. I would then check that the frame hasn't bent open like mine from the previous owner over tightening the bulb pusher. If still leaking I would then replace the valve seals and o-rings. Make sure the o-rings are suitable for co2 Hope you get it fixed buddy 👍

@@bingobango7734 Hi friend. ...when you will release KWC or other brand videos about the Colt single action army and Colt 1911 ???

@Dan-Commando hello buddy I hope to get a 1911 video up sometime in November I have 3 different models each with different mechanisms

@@bingobango7734 3x models each with different mechanisms ?!! I wait for your videos and opinons about thoses mechanisms as well ! have a nice weekend ! :)

@Dan-Commando Hi bud yes the gletcher 1911, ASG sti 1911 and a colt combat special edition and thank you I hope you enjoyed your weekend also

Hello sorry for the late reply I have been out of action for some time. Can you attach a picture of the one you are missing I could measure mine so you can search for a replacement

Hello sorry for the late reply I have been out of action for some time. Bagnel and kirkwood, ebay and some umarex airsoft parts can be supplemented hope you can get it fixed buddy 👍

Hello sorry for the late reply I have been out of action for some time. I think you summed it all up spot on with a little tweak to the hop up these are an awesome plinker. Very snappy blowback and feel awesome tapping away at targets thank you for the awesome comments I really do appreciate it 😀

Hello sorry for the late reply I have been out of action for some time. Hopefully you found this useful buddy 👍

@@bingobango7734 thanks for your kindness 🌹

Hello sorry for the late reply I have been out of action for some time. Thank you for the positive comment I really appreciate it

Hello sorry for the late reply I have been out of action for some time. I will be putting up another video of a complete restoration of one, including how I make the leather washers for it hopefully it will help

Hello sorry for the late reply I have been out of action for some time. Thank you for the useful information I will try sorting a Mic and better lighting for future videos

@@bingobango7734 A Ultimate Mod allow you to make the walther look like the real steel version.The maker mention : " The PPK and the PPK/S are two different guns. But the PPK/S (which the replica is based on) is basically a Walther PP frame with a PPK slide which was done for some U.S requirement. I had the CO2 replica which I modded. Since it's a PP frame I was able to purchase reproduction PP grips and fitted them on to the air pistol which was a nightmare of a task with aligning the spring clip. I also chopped off the rear bottom corner of frame to make the extended magazine stand out more. To me it looks much better than the stock version."

Hey have already replaced yours? I have the same problem and i think inside the magwell are these two metal things holding the hammer assembly in but this guy seems to have just brute forced the part out.

@@santerisuuri5139 I tried but I don't have the tools to do it. I ended up selling my slide and mag. I still have the new hammer and all other parts, just gonna sell the rest and get the umarex glock 17 gen 5 t4e .43 cal.

Hello sorry for the late reply I have been out of action for some time. I haven't had an issue with my hammer section yet and remember thinking if I was to take it apart I would firstly take a bunch of pictures showing where all the springs and sears were sitting. I'd then clamp it together and tap out the pins and slowly release the clamp it would be worth covering with a cloth to prevent the parts pinging off. Now putting back together is where I'd see the challenge as it looks like a few bits would have to be held in a position to clip it all back together. If I ever have a hammer issue I will definitely put up a video to try and help.

Hello sorry for the late reply I have been out of action for some time. Thank you for your comment buddy its helpful information I will try sorting a mic for future videos and possibly recording new audio over this.

Hello sorry for the late reply I have been out of action for some time. I believe the plastic cover replaced a metal version at one time which was after the exposed ones but I'm not 100% certain I have that the correct way round . All it does is seem to offer a slight bit of protection from the spring hitting against the outer barrel frame.

Hello sorry for the late reply I have been out of action for some time. Thanks for the useful information buddy I will sort a mic for upcoming videos and if possible record new audio over this one 😀 👍

@@bingobango7734 Brillant video , i just subscribe ! please do 1911 Co2 :)

Hello buddy Many thanks I appreciate it my next video will be on 3 different types of 1911s as suggested by another viewer as they all have different mechanisms

@@bingobango7734 FANTASTIC :) !!! Thanks you so much. + here a photo mod you can do for your walther ppks to look more like the real firearms : (I can provide online photo in private message but the website link are erased my youtube. The maker mention : " The PPK and the PPK/S are two different guns. But the PPK/S (which the replica is based on) is basically a Walther PP frame with a PPK slide which was done for some U.S requirement. I had the CO2 replica which I modded. Since it's a PP frame I was able to purchase reproduction PP grips and fitted them on to the air pistol which was a nightmare of a task with aligning the spring clip. I also chopped off the rear bottom corner of frame to make the extended magazine stand out more. To me it looks much better than the stock version."

@@bingobango7734 if you can only have one get the KWC 1911 (made by cybergun) from what i can see online all the modern Colt 1911 co2 are build the same (KWC , Gletcher , Tanfoglio witness 1911 etc ) but im dont own them (just the KWC) and im not a specialist...

Hi Bud thank you what is it about them you are not that keen on ? I think the only bit I'd definitely change would be the bb pushing rod on the magazine I find it tricky to load

@@bingobango7734 Hi. Very beatufil pistol but very low power 1.2- 1.3 joule and very very very low accuracy. Thank you again for a great video.

@Giuseppe Aquilani Ahh OK have you tried winding out the hopper screw then test and wind in to tighten up your shots ? I literally had to turn mine just over a quarter of a turn to get it shooting straight

Hello buddy I'm sorry to hear you have been having problems with your one what are the issues you have been experiencing I am still trying to find a good lead bb for it I've tried the copper coated ones but they do get jammed every few shots

@@bingobango7734 Hello. Finally, after three days I managed to put the main (trigger) spring on its place and the gun is active for the moment. Not sure for how long. Concerning BBs - never had your problem. I use different ones: steel and copper coated. Prefer still - can use them several times (if found in my garden)!🤣

They can be fiddly to get the spring bar situated correctly the only reason I'm trying the lead bbs is because of it rifled barrel the steel bbs will work great but eventually will damage the inside of the barrel if you find ammo that works well with it please let me know buddy I'm glad you got yours working happy plinking

@@bingobango7734 I don't think you need to worry about the barrel. Nothing happens to it. Anyway, this is not sports target gun - it's just a replica model - suitable for plinking.

This is true also in the uk they are slowly trying to introduce a ban on lead shots and pellets

Hi buddy the pistol itself is a similar steel body as the non blowback version unfortunately the blowback version has an all plastic magazine which is the only thing I'd change about it really the co2 cartridge loads into the grip unlike the non blowback magazine where it holds both bbs and the co2 the magazine the blowback works cocking the hammer back the trigger pull feels a lot lighter compared to the non blowback version

If it would be helpful I can do a short side by side video for you on my channel just let me know buddy

@@bingobango7734 Thank for fast reply! Comparison video is not necesary. I have the standard version. But thanks. It only curious me because the latch in magazine looks like separate part, which made me suspect it was steel. But no? Is the slide stay in back position after last shot?

Not a problem buddy The magazine release catch at the bottom of the grip is still metal but the slide catch release doesn't function so no locking back

@@bingobango7734 or if you ask.. maybe you can make a video of accuracy shooting on paper at 10 meters? , by any method, just this distance and try to be most accurate. I want to compare with accuracy of my non blowback.

Thank you I really appreciate the nice comment bud

@@bingobango7734 Man , 10 month without one of your great video... its pretty long. PLEASE make dissasembly/assembly of the KWC/CYBERGUN 1911 and same for the UMAREX Colt single action army. that just would be awesome ! (thanks)

Hello sorry for the late reply I have been out of action for some time. I will be doing a 1911 video sometime this year.

Cheers Lee I appreciate it buddy 👍

No problem buddy it was my mistake i must have had a total brain fart moment when up loading the video i hope this video helps 😀

@@bingobango7734 i finished it. It works now thank you so much🤘. One more thing i know bug but what was your solution for the co2 air seal not having enough seal?

@@silenthunder5657 That's awesome buddy I'm glad the video helped for the Co2 seal or any o-rings soak them in pellgun oil for 72+ hours I have heard people using other oils from brake to transmission but I have never tried that myself and would be worried it may damage them if they look like a squirrel has had a go at them it's a replacement jobby

@@bingobango7734 thanks bud

​ FANTASTIC :) !!! Thanks you so much. There an Ultimate mod you can do for your walther ppks to look more like the real firearms.The maker mention : " The PPK and the PPK/S are two different guns. But the PPK/S (which the replica is based on) is basically a Walther PP frame with a PPK slide which was done for some U.S requirement. I had the CO2 replica which I modded. Since it's a PP frame I was able to purchase reproduction PP grips and fitted them on to the air pistol which was a nightmare of a task with aligning the spring clip. I also chopped off the rear bottom corner of frame to make the extended magazine stand out more. To me it looks much better than the stock version." I can provide photo.

Cheers Lee appreciate it buddy 👍

Hello bud I believe the 2020 blowback ones are the first they have done I also have the non blowback version that still is my favourite out of them both I think the plastic magazine on the blowback ones let's it down a little it is still a great pistol

Hello Nick I am uploading the rebuild video now I hope this helps 🙂

@@bingobango7734 definitelly ;)