วีดีโอ

friggin sweet

Nice video.

If you didn't figure out the issue with your top drawer try this. Get some flat self adhesive magnets and apply one on each end of the drawer and one in the middle on the backside of the drawer and the mating surface on the inside of the cabinet itself. Combined thickness of the magnets should be less than an 1/8" total thickness. If you dont like the magnet idea, try velcro strips.

Nice fix! Looks good!

Small but powerful

I feel for your groans of pain. Don't be tight as a fishes bum... It's false economy to use solvent depleted glue (jello). The solvent is needed to weld well into the PVC. That solvent (Methyl Ethel Ketone) is nasty and evaporates out of the glue very quickly. Exposure can cause dizziness, lightheadedness, headache, nausea, blurred vision, and may cause you to pass out. Repeated high exposure can damage the nervous system and may affect the brain. It has a high fire danger. Replace lid ASAP. I used it last week and I could taste it hours later after several coffees & dinner and that was not in a confined space. Doing that repair, first I'd buy 'Primer fluid' and new glue > Apply primer fluid and wait 30 seconds then scuff up. It softens the plastic pipe and old glue making it easier to skuff up with abrasive paper > Apply primer again both sides > Apply new glue both sides > Bung it back in and hold for a good 30seconds > Leave the confined area 30minutes to get the sickening taste of MEK solvent from your nose, lungs and mouth > Return to check pipe fully engaged and place a sheet of newspaper under > Use the basin or whatever feeds water down that line and check the next day.

Who brush hogs with chain

She looks good

Cutting good now!

Thanks for not saying what you paid 😂😂😂

They painted over rust at the factory .

Nice fix!

The classic fuck u t shirt. Never goes out of style

Good hack 👍👍

That was very nice to help Mom out. Did she use it yet? My wife has the same problem. Now you got me thinking about a window closer... I found your channel a couple weeks ago..I subbed . I like your style. I finally have time to watch a few vids. I'm George by the way.

Nice problem solving. What brand of vise is that?

Excellent tool box hack! Good job Brother! Had a laugh about catching that B in the face. Been there before!

what would a u-35 be?

Great job grandma would be proud of you and it is a great mother's day gift thanks

Love the idea 💡😉👌

How do you see wht you have in the top drawer? Seems high🤔

This one made me laugh keep reviving the dung!

P R O M O S M 😃

Thoughtful and well done! That will make a very special Mother’s Day gift for your Mom in remembrance of her Mom.

You should use some cutting fluid and maybe turn the speed down a bit.

Mcmaster carr sells rod ends for 20 bucks, and you are done. What is all you time a trouble worth for a temp fix?

This one video was enough to earn my subscription. I like the way you work. Well done!.

"It's a bucket of turds." LOL! 😂

Looks good, bud. I hope I can come across a deal like that some day! :)

Looks great.

Great job!

A lot of work but it looks great!

Excellent job!

can't put lipstick on a pig. you need to start with a better grade of steel. that garden store carriage bolts are junk steel.

That's great

Thanks for sharing this I’ll be buying it

I very much recommend doing a pressure and vac test on the case before spending a dime, the clutch side bearing and seal setup is no problem to get but you can just about forget getting the combination bearing/seal that is on the flywheel side of the crank. If the case is not tight no carb kit or new carb will turn the saw into a reliable backup. They were fantastic saws though.

Great stuff. Expensive but mt go to.

Great solution. It's funny watching everything backwards. Tightening turning left. Threading left and screwdriver going left to tighten. Weird how that works on some cameras.

Thanks for an excellent educational video. Adapt, Improvise, Overcome, you possess a great deal of patience. I would have been very upset and given Harbor Freight a lot of grief over this shoddy workmanship. I like your "thinking outside the box" and finding a solution.

Quick and easy trick, thanks!

Thanks for the steel wool tip!

Good one

Should paint it bright orange so you can find it after the snowplow hits it

Definitely Innovative!

OK!!!