วีดีโอ

Mines so hard to tell, im going to try that, thanks ❤

I need to get my leon sorted and out on track .

Here is a tip once you put the handbrake cable on the brake shoe then put the top spring on then the adjuster then the bottom spring they should hold themselves together enough so put it onto the backplate placing the side with the wheel cylinger starting eoth the handbrake side put that on fullyso the top and bottom is in place and put ita retaining clip on then all you need to do is use a screwdriver (anything that you can use to pry) pry the bottom of the other side into place and then out the retaining clip on (it is possible to do on your own)

This is really cool.

Very good video mate fairplay

Thanks

interesting idea that.. isn't the card going to turn to mush with all the condensation after a nights sleep ?

I'm looking for tools sizes needed to remove the bolts😂

Nice 😮 I'm definitely doing it to my fez . Thanks for the inspiration! ✊ 👊

Good review mate

I cannot seem to get the boot in flush. Piston goes in fine. Tried pressing I'm and hammering in but no use. Any advice? Don't want to start filing down the caliper.

Legend I've been thinking about doing this to my fez

thanks for the video just bought a 07 fiesta style and tried to put fuel in and have that problem managed to get it open but is tight going back to close will try it

I think my tab must be kn*ckered... No matter how many times I've tried with a small screwdriver, can't find the damn thing to push it down

Hi mate, is this the ST150 subframe ?

What’s the foam cannon carrier called? I’ve been looking all over and still can’t find it. Thanks

Try that with the engine on.

You're a damn fool!

bro car exhaust is hot... spraying water will just turn to steam and be useless

what size shoe do you wear?

You forgot the most important part. You have to start the engine so the exhaust will pressurize.

It ist not necessary to dismount the steering rack arm. Never the less, Dankeschön!

Thank you sweet baby Jesus, I’m not alone, lol.

I do this just after I pull up at the MOT place... that computer payed for itself in the first yr.. lol

Still shouldn’t pass with SRS warning light on, sort yourself out with a resistor for the missing airbag in steering wheel there cheap and easy to fit

Is this 20mm all round ? People saying to put 15mm at front and 20mm at rear ?

How are they holding up?

have you got a link to the tool you got from ebay, thanks

Great video!planning on doing this myself. Did you use the jack to support the engine?or is that not needed?

Great work mate, how long did this take roughly ?

I am stuck with that same problem! I will try it! Thanks!

A catch can is definitely worth it.

Now i wonder why the previous owner fix it with screws.i got 6 😂

Can I connect it to rain water ? Will the rain water cause motor malfunction?

Doesn't show what was used in order to replace the top spring, makes it very complicated to replace the top spring not knowing exactly what tool was used to do it.

Hi mate where did you get these shoes from and do you have a part number keep getting sent the wrong onea

Super Video.Thanks!

Hi, how did you know what size belt to fit afterwards? Thanks.

Cheers bro 😊

Did you tension the handbrake cable from inside after fitting the drums? Looks like a new one is needed though if the anchor on the axle is damaged.

For the money you've spent you might as well have fit the ST150 rear calipers, in addition you only need new stub axles, brake hoses, handbrake cable. So much easier to service.

😪 "promosm"

Great video mate. I've got a mk6 1.6tdci and watching your videos has given me the confidence to just have a go at replacing things. I have 207,000 miles rn and the rear drums are next after the front end suspension and lower wishbones. What were the drums you got? Can't get a straight answer out of Autodoc, too many options for them all to be right 😅

I have a mk6 zs petrol, and lately it will go into 4th and 5th easily, but there’s absolutely no power in them, once they go into those gears the speed hardly moves. Would it be a safe bet that it’s a clutch issue?

i had a problem with my handbrake cable on my mk6 fiesta , the nylon grommet wore out and it wouldn't hold in place, i just had to replace a small part of the cable , thanks for the videos, please do film your ongoing fix of your handbrake,

No protection against the heat of the engine bay on the POD filter? Even a Π shape box would help.

Looks awesome!💪- I like your style and type of modifications to your Z👍 Being a new subscriber to your channel; I really enjoy your (build) videos and your "authentic format"😊 Keep building, modifying, and uploading, cheerZ from Denmark😊

makes me feel like I can paint mine as well my hood needs it bad

Dankeschön

Brilliant work, very well done. I can highly recommend PPF for the leading edges of the side skirts and rear spats as not painted the stone chips will murder the finish!! ask me how I know 😢