วีดีโอ

How do you remove the coil? I see it's inside behind points.

Very nice explanation

So, once you've poked the holes in a row, would it be possible to clear the tranch just by pulling the auger along slowly with the tractor?

Odd to see live pto but no fast hitch

I LITERALLY just bought a new driver pannel, to get my driver windrow to roll back up, it all worked great and fine, until, while fishing, i stupidly left my keys on my seat. Grabbed a wire, lifted my driver door corner, shoved it in and pulled my driverside open pannel, got in and now my front windows dont work again. AM I BEING PLAYED BY DODGE? Or is that a safety thing that makes no sense to me?

Do you plan on posting any more videos?

Thanks

Great video Zeke, thank you.

Hey I know this is an old post but this guy Zeek the antique freak just doesn’t show how he did this job start to finish which we all need and he darn right misses mentioning the removing the back two bolts also holding that solenoid onto the starter and near impossible to get at as well

Did you ever make a hand sketch ov this Onan regulator board?

I have a 64' 4020 powershift

I have john deere x350, i cant find anywhere in manual how much clearance is needed for those v valve. Could not get any help from local john deere too. Anyone knows about it, please let me know.? Thankyou

What site do you suggest for OEM parts for this specific deck? Are there any aftermarket that will work fine to save money in your opinion?

How’d you get the axle out? I’ve been slamming it and it won’t come out

Thanks for the video.

Can you show video of removal and installation?

My 2009 3.3 se is doing the exact same thing, new button module didnt work

what is a reasonably priced starter for the 4g32 engine

I will check this place out soon, perhaps I could confront the owners?

Hey there i would love to know the measurements for your adapters if we coule get in contact. Thanks. Have a 300 utility and 3 pt hitch would be a great improvement

Use you vidio to install a mag on my dads v4 did not work after servel hours flipped it 180 and now runs

I’m struggling on the 60 I just got. When you snap it in and take off or in Netural. When you pull back on the lever. The pulley doesn’t stop turning and the tractor keeps driving. It’s been sitting outside in weather with pulley cover off for the last 20 years lol. Ran 3 years ago tho. I’m hoping I’ll adjust a tad and will fix it. When I pull back on the clutch lever further. The pulley engages again lol

Shame on FORD for being such d. heads when it comes to accessibility with this engine. Years of engineering and design and this POS is what they produce? Touted high on Wards best engine list but thats until you have to do work on it.

I own a 050 av, and I was wondering if I could put a 36 bar on it and conserve the 404. Chain? Is it possible or I nedd to switch to 3/8?

Hey Zeke... Im working on my older 540 bobcat trying to change out a few hydro hoses.. i need access to remove the steel lines under the lift arms.. I removed both lift cylinders on the boom arm.. trying to raise the boom with an overhead winch but the front wheels just come off the ground.. i have locked down both safetys with a strap.. do i need to work the petal to unlock the boom arms? Any help would be greatly appreciated.. Thanks

I do this and every time I plug it in the breaker blows what's the deal

For the price of these things it really shouldn't be that hard for them to have a drain plug

The differential side you don't have to worry about air etc. as the hydro side right! Thanks much again!

How much oil total did this hold? Thanks!

Quick question, when operating the tractor and not needing the pto do u run it in the detent position or the brake position?

Please don't make any more videos.

Now that you have done this could you make a sealed unit serviceable without opening it? If you see where I'm going...

I am the proud owner of an LX279 as well as the slightly newer LX289 lawn mowers... both purchased second hand from local JD dealership.I like the fact they have liquid cooling system. Bofht as is where is. Learned a valuable lesson , bought on a saturday , took it to the farm , , first round cutting grass , would not climb slight incline , side of the driveway.... low oil level in transmission... No . Loaded her up , back to the dealership... ended up buying a new transaxle , dealership swallowed the labour cost for installation. Note to self , if ever buying a second hand lown mower , test drive needs to include climbing a grade to make sure no issues present !

thanks for sharing... that is one of the nicest 4020's I have seen , she runs real smooth ! A 60 year old gem !!

Great tips from a cheap bastard .

I have gas getting into the crankcase. Would the fuel shutoff prevent this from happening? If using everyday bobcat starts good but if it sits awhile its hard starting.

Even though your vid is 7 years old it is relevant. Changing plugs on a 5.4 is an all day job if you take your time.

I have the same van. Similar wiring issue. The purple wire that operates the interior light broke. Soldered it back together. All good.

Do you have a video of removing the old bearings out of the housing and reinstalling them? Thank you

I have 642b what do the warning lights on the front dashbord mean

I wandered around in that place thirty or forty years ago when I drove trucks from the potash mines back here to the states. I don't remember that many artifacts on the walls back then.

Im rebuilding one of these right now, and the power enrichment valve spring was missing, rendering the power enrichment circuit usesless. I wanted to verify this application requires one. I see one sticking out of yours, I cannibalized a holley power valve for a spring.

OK THANK YOU .

Q: it's that possibility to see year of factory in serial number, my engine have 1936 in 4 first carater?? the engine have cast iron head.

Bobcat 642B 1986 Gas Mitsubishi 4G32 engine it´s leaking oil in the oil seal and the back case do I need to remove the motor or can Ibe able to installed with out the motor on and if you can guide me where tobuy the seal or gasket for that thank you and parts.

Hello. Is there an oil adjustment screw on the 051s like to let more or less oil to bar

If i excite a 1 wire self exciting alternator, will it turn a 12v generator motor

There is alot of parts you could take off that engine and be a simple engine did you put one way valves out of spark plug holes

I’ve watched this video several times and it is informative, however!!!!!!! Why can’t you move the camera your using to make the video further away from the parts you’re filming so you can see what the hell you’re doing. All I see is your fingers and the camera moving to quickly to see what you’re doing!!!!!

I like to ask you a question about the timing gears