- 4
- 50 065
ETSNZ
เข้าร่วมเมื่อ 31 พ.ค. 2016
Dedicated for the support of Schneider Electric products
ETSNZ: Altivar Process RSlogix EthernetIP
Basic steps to setp up a Rockwell Allen-Bradley CompactLogix PLC with the Schneider Electric Altivar Process 900 using Ethernet IP
มุมมอง: 11 596
วีดีโอ
ETSNZ: Configure Altivar Process and PC for Embedded Ethernet communication
มุมมอง 14K8 ปีที่แล้ว
Basic VSD and PC configuration guide to communicate over Modbus TCP/IP to an Altivar Process
Good video
Hi. Did you have the actual drive connected when simulating?
Can I use a PLC Siemena S7-1200 to Control de VFD via embedded Ethernet Port? I saw a video where it shows that the use of an external module VW3A3720 is mandatory. Why? Thank you.
nice video! thanks so much !
I can find com parameters-> embedded ethernet
Ok, how do you do it with the EDS file now?
What is the bit mapping for the control/command word (O:DATA[0])? Bit 0 must be "run" but I am assuming the other 15 bits also have some functionality.
I need this but for siemens
Hi Mr, I saw that you use RD REF and WR RED with value "0" is that the modbus registers, because I saw after that in the VFD the modbus register, one begins 3201 and the other in 8501. What I'm missing in this configuration?
if you look this pdf , its programming manual for atv9xx series media.distributordatasolutions.com/schneider/2016q2/fef677e41765147443ac338c0ffc3ad128a2d0f9.pdf look for page 540 and 541 so you can see the Address of the first input word is 3201 (EtA) and Address of the first output word is 8501(CMd).
For me also same doubt
I have a problem connecting the PLC and altivar 630. The connection is there, but I can't run and monitor the Frequency changer parameters through the PLC.. can u help?
Good evening, I would like to ask you a question, I hope you can help me, I have a m340 with the included tcp port, as it would be to access the atv600 registers, I do not have a NOE module
Really nice video sir.. Can you share something about atv process 980 regenerative vfd's
could you send me this version of somove?
anyway, i want to ask for NST status? how to fix to RDY status? thks
Awesome bro
tendras un arranque por RED ETHERNET CON separate
Thanks for the Support..!
EL MOSTRO JAJA
@@MRKD_Studio El mostroo haha
Hi Could i perhaps have the contact details of the author for this video, or email me at werner@automationtube.com Thank you
Exelente video, por favor puedes hacer el video con M580.
Excelente video, muy completo!
Useful video... But it is showing overheating fault.. as i moniter with my laptop
thanks , please increase audio volume .
How much faster would you say this is over the Schneider RS458 to USB cable? I'm noticing the USB method to be atrociously slow.
Hi Preston, I have found there to be a slight improvement in communication speed when communicating via Ethernet TCP, however, I believe the limiting factor is the refresh/scan rate of SoMove which cannot be adjusted. But Ethernet TCP is better for other reasons such as the obvious - no more usb to serial adaptor cable, also if you don't have SoMove on your PC you can access the VSD web server to change parameters and extract the configuration.
REALLY GREAT
this procedure is the same for a ATV 71 ? on a Ethernet card?
Hi Moises, the procedure is very similar when using the Modbus TCP ethernet card on the ATV71 or ATV61. There are some small differences that you must be aware of. The scanner table will be a maximum of 11 words read and write, however the first word in each is a reserved word and needs to be ignored.
how setup DI 1-6