- 264
- 706 560
working with Larry Mullins
United States
เข้าร่วมเมื่อ 29 พ.ย. 2012
working with projects, building, cars, machines, tools, plumbing, any projects with friends and family.
engine parts cleaning, here's what I use!
Getting into the dirt doing the behind-the-scenes parts cleanup that they never show you in the reality shows. at least what I use!
มุมมอง: 71
วีดีโอ
harbor freight central machine 20 gallon parts washer unboxing
มุมมอง 9314 วันที่ผ่านมา
checking out the parts washer from harbor freight , not the best shape out of the box, but assembles easy enough .
removing the heads from Dads old 1988 chevy truck
มุมมอง 36หลายเดือนก่อน
just relaxing in the garage and listening to music tearing the engine down in dads old blue 1988 chevy silverado
1999 to 2004 mustang window regulator replacement
มุมมอง 882 หลายเดือนก่อน
replacing a window on a 2000 mustang gt convertible .
2015 ford F250 Super duty front brakes and rotors replacement
มุมมอง 1503 หลายเดือนก่อน
2015 ford F250 Super duty front brakes and rotors replacement
looking at cheap ratchets, are they worth it?
มุมมอง 1073 หลายเดือนก่อน
looking at cheap ratchets, are they worth it?
starting a YouTube channel, don't do what I did!
มุมมอง 2448 หลายเดือนก่อน
starting a TH-cam channel, don't do what I did!
Chevy Nova no crank issues. key start relay/switch replacement
มุมมอง 8958 หลายเดือนก่อน
Chevy Nova no crank issues. key start relay/switch replacement
1976 Chevy Nova gets new pipes and front fenders replaced
มุมมอง 2218 หลายเดือนก่อน
1976 Chevy Nova gets new pipes and front fenders replaced
Gm turbo 350 automatic rear transmission seal replacement
มุมมอง 3519 หลายเดือนก่อน
Gm turbo 350 automatic rear transmission seal replacement
Rode wireless ME mic unboxing. Is it better?
มุมมอง 289 หลายเดือนก่อน
Rode wireless ME mic unboxing. Is it better?
Did I buy a car with the "Best/Worst" engine GM has ever built?
มุมมอง 3859 หลายเดือนก่อน
Did I buy a car with the "Best/Worst" engine GM has ever built?
1976 chevy nova fuel line and project update
มุมมอง 5111 หลายเดือนก่อน
1976 chevy nova fuel line and project update
1976 Nova timing chain cover replacement
มุมมอง 6911 หลายเดือนก่อน
1976 Nova timing chain cover replacement
chevy nova project headers and body tear down
มุมมอง 10211 หลายเดือนก่อน
chevy nova project headers and body tear down
1976 Disco Nova gets new parts! sorta...
มุมมอง 124ปีที่แล้ว
1976 Disco Nova gets new parts! sorta...
2011 to 2014 chevy cruze 1 .4 turbo evap codes ? This Dorman kit is the solution!
มุมมอง 661ปีที่แล้ว
2011 to 2014 chevy cruze 1 .4 turbo evap codes ? This Dorman kit is the solution!
Yet you didnt do this for your “whats the earliest you can get max stats” run
1985: American Tool Company bought Petersen Manufacturing. 1993: American Tool Company bought The Irwin Tool Company. 2002: Newell Rubbermaid bought American Tool Company. 2003: American Tool Company changed its name to Irwin
Not in Nebraska no mo
@@Simonofcalifornia yep, they’re owned by Stanley Black&Decker, made in China like everything else, which isn’t always a bad thing despite what people will say / complain about.
@dak_yo sbd. Owns so freaking much. They just bought out mtd recently so they own a huge parts of the outdoor yard care market
This is literally one of the best comments ever. It's short, concise and to the point, and I literally just learned more than I thought I ever would on the subject. Thank you for taking the time to educate us all, you're a scholar and a gentleman and I award you all points, which makes you the real MVP. Edit: I want to thank the uploader too, he created the content that helped me see into this a bit, which also brought others here. If the uploaded keeps attracting solid people like op of this thread, he is going to build a great community and I'm here for it.
Mines was missing wtf doorman
I'm getting dizzy
Z e p is the only one that's any good anymore the rest are trash purple Power is trash greased lightning is trash they are no longer powerful and it's been this way for like 6 or 7 years
How did you fix it?
Replaced with a new line.
mine is rusting away in my back yard. unused for years. but when i bought it i used it to exesave amounts. worked great. BUT i had to go to nevada to get the wash fluid as cal would not allow it to be sold in state.
Now if we could do that with girlfriends would be all set
Car will be repossessed within two years.
i did not know Jack Blacks stunt double shops at Carvana! How cool
It eat the shoulders off the nut if you’re using it wrong.
Luther vandros
2001 or newer but Not a 2000 model based on the hood scoop
The famous nut rounder.
The adjustable wrench is also known as the west Virginia socket set
Good Vid with good information!! I could do without the background ditty though.
Yeah, I’ve quit the background music! Thanks for checking out the video!
Did you use some spray oil on some areas? A neighbor gave me a TB 210. Says it runs but needs gas. Can the front drive gear box be removed so the mower is just a push type? Thank you. Think the mower is a pull cord type
I haven’t tried removing the drive gears, but it would still be heavier to push than a regular push mower. I use penetrating oil on the brake cable and on the blade.
@@workingwithLarryMullins am hoping tomorrow to do a test start on it, with fresh gas, and a short air intake inspection. Think the oil is overs serviced, so want to lower it some. The oil may have been a little over filled for winter storage.
They make one end with flat sides so you can use a pipe wrench of a Cresent wrench to hold it.
Wow everyone in the comments is dumb as hell he literally says he's taking it off in the first few seconds and ya'll telling him bad advice for installation
Thank God this video came up. I don’t know what I would’ve done not knowing what you were up to
Pretty simple, just take the lag bolts out of the harmonic chastity belt and liberally apply locktite to the bolts when reinstalling. Never have a problem after that
use a air impact no leverage bar needed
@@SerpentBornOfficialair impacts spin fast enough that the engine won't turn.
@@SerpentBornOfficialwith the pistons still in the block they will provide enough friction to use an impact
@@MrJ183 thank you for explaining to a person that didnt understand
the uggh dugga brother
Phenomenal video. Thank you
You're half right/half wrong on the body lift not increasing ground clearance. If the aim is to just increase roof height then yes you are not getting more clearance, but say however you're stacking a body lift on top of a suspension lift to make room for bigger tires. Those bigger tires in addition to the pucks will give you more ground clearance
Sorry big tires on there own are what increases ground height. But if you're already trying to get bigger you may as well use any way possible. An 8 inch lift is pretty cool on its own, but 8 inch lift on 3 inch pucks is the difference between running 37s and running 40s in some cases. Great video
Thanks, this fixed my mower. I also added an inline filter so this does not happen again.
That oil return tube made out of metal is a super pain in the ass. I just returned the metal one and picked up one that was plastic like the oem only took 5second to install that one
I bought a feed line off Amazon. Installed with new turbo. Leaked as I filled reservoir. Took line back out after removing catty. Replaced seal washer. Tightened to turbo and still leaks. Insanity… going to dealership for OEM if that’s my only hope.
The coin just falls out the bottom 😂🤣 definitely not set up
It’s meant to fall out so you can keep the coin lol
Infinite car glitch
Hey Larry experiencing same problem on 2014 Chevy Cruze Lt. 1.4 liter with turbo. My question is if I change the intake manifold with dorman manifold will that fix the problem permanently with the check valve inside manifold? Thanks for the video any feedback appreciated
We used the Dorman, it didn’t work. Same issues. We ended up using the aftermarket kit that the guy on TH-cam sells. It seems to work fine. I think the page is called cruzekits or something like that. If you replace the intake, I recommend using a GM part. I haven’t had any luck with any dorman parts.
So you dont recommend Dorman but you are using Dorman is this product your promoting no good??@@workingwithLarryMullins
How many miles on that bad boy?
200000
Thought we were watching a vid on how to replace the lights not an Amazon plug
You didn't get ripped off that's how they are from doorman I believe when you tighten the line it expands and that locks it in place
I have a bunch of brand new oe connectors in my toolbox…. want some
We finally got it sorted, thank you though. lol
Life time warranty if you dident know
Thanks, I didn’t know.
Damn right. Just perfect 😊😊😊😂😂😂😂
WTF
What about the inner axle seal???!!
I’m sure I replaced the inner seal, and filmed it, but you are correct, I didn’t show that part, sorry about that.
I taught my daughter how to work on her bmw! She has come a very long way and she isn’t afraid of getting grease or oil under her nails! Next thing I’m gonna teach her is how to weld and build exhaust!
She has been in the dirt since her first car. Getting dirty makes her appreciate what it takes to keep up a vehicle. I once thought we had lost the next generation, but proud that some modern kids and grandchildren are keeping up the tradition!
That’s a ton of miles of neglect to get to that point. Nice to see her doing it herself
Very inspiring, there may be hope for this generation yet..
I'd be a proud grandpa 😊 Teaching her right.
Proud that all my kids and grandchildren can fix their own stuff! Very proud grandpa !
I installed that same kit about 4 years ago. Great price, works great still
Akebonos
What’s the easiest way to get them to Phillips screws out of the rotor?
Impact driver. It's like a spring-loaded screw driver that you hit with a hammer. Usually, it only takes 1 or 2 good smacks to break the screws free, and they are relatively cheap
What Kyle commented is what I use. I think my impact screwdriver came from harbor freight. They are relatively cheap and work great on rotor fasteners.
@@workingwithLarryMullins Thank you, Mr. Larry 😁
I redid my whole front end of my car with detroit parts 2 years ago. Outer tie rods are worn and the warranty is a lie tbh. Not bad but no great
Junk
Detroit axle sells great kits! And at fantastic price
They lasted me one summer lol