SUPER HELPFUL!! I needed to swap some leads on my winch solenoid ( though I had it memorized but I started to doubt myself) and now that I know how the motor works I was able to draw a simple wiring diagram. Now I understand and can trouble shoot. I feel like I just found the holy grail.
Saved me a lot of hassle. My wireless winch controller broke and had a 3 week wait on a new one. I use my winch to tip a firewood trailer. Now I can tip it again by bypassing the solenoid. Appreciate it.
Super helpful video, thanks. I just got off the phone with Warn, and their procedure is one step different. They advise attaching one side of a the bridge cable to Armature, leave the other free. Then apply power to F1. Then connect the armature bridge to F2. Then disconnect power and bridge, put power to F2 and then connect bridge to F1. This apparently isolates components somehow, I didn't follow. When I tried your method, all I could get was a spark on the negative. With their method, even though it looks like it should be identical, my motor works fine in both directions. Again though, thanks for making the video. super helpful, and got me started down the path to learning that my motor is fine. Keep up the good work.
Awesome, bump for part three. Have an M1200 that I have to tap on the solenoid box to get it to operate half the time. Also just got a used industrial 15k that I need to go through and build a control pack for.
@spsingam Try using penetrating oil on the shaft the clutch knob is connected to. A lot of times there is corrosion between the shaft and case which prevents you from pulling the knob out all the way. Next step after that is to remove the two bolts that holds the clutch assembly to the housing and carefully remove it. Ensure that it is indeed sliding in all the way then reinstall.
I don't own a Warn winch I own what is probably a cheap Chinese copy. My solenoid box for the winch controller rusted out after only a few years and it let me down on the trail when I need it. I rebuilt the solenoids with new parts and I put a bunch of Dielectric grease on it. After thinking of ways to waterproof the controls I decided to pack the whole controller box full of grease. I'm hoping that this works longer than nothing but I won't know for another year too feel free to comment what you think
I like the dielectric grease idea and use a lot of it in connectors, but I mounted my solenoids unde the lid of an ammo can away from my winch (they don't need to be next to it, that's for manufacturer and installation convenience) . The lid flips open and I have total access to noids and wiring. I use welding cable and lugs to make custom cables. The lid and solenoids are removable as a unit by sliding the lid hinge laterally like any other ammo can.
First thought is main power wires are hooked up wrong. If you are unsure do NOT attempt to run winch anymore. If you know the main ground and power is hooked up correctly then go to the solenoids, do you hear it click in either direction?
@CATERPILLAR414 Heck no, I have another M8000 that works great, a 9.5XP I'm scabbing parts off of and two 8274s I'm rebuilding. This other M8000 belongs to a friend.
josh tesseneer I had that problem on a rew8000 I did allot of power testing and I found this weird wire that runs to both bolts that you connect your power to and in the middle it has a little red pillow shaped thing I think its a fuse but I can't find one. that maybe your problem. ps its inside with the motor
Good Clip - thanks for sharing ! i got an old Warn i think its some 8274 winch. it rolls and unroll ok, but can seem to get the "free wheelling" clutch thing to work. anyone with ideas ?
However most sockets and wrenches are broached so they fit both and any mechanic knows this. 9/16" swaps with 14mm, 7/16" swaps with 11mm etc. 8mm swaps with 5/16" (handy on many electrical nuts and hose clamps).
I know this video is over a decage ago ... but still helpful ... thanks a million ..
Bro u saved my ass out of a whole lot of trouble , relay broke and needed to hardwire the winch motor. Thanks a lot!!
SUPER HELPFUL!! I needed to swap some leads on my winch solenoid ( though I had it memorized but I started to doubt myself) and now that I know how the motor works I was able to draw a simple wiring diagram. Now I understand and can trouble shoot. I feel like I just found the holy grail.
Saved me a lot of hassle. My wireless winch controller broke and had a 3 week wait on a new one. I use my winch to tip a firewood trailer. Now I can tip it again by bypassing the solenoid. Appreciate it.
This got me out of a tight spot in the middle of the woods in a swamp. Thank you!
Super helpful video, thanks.
I just got off the phone with Warn, and their procedure is one step different. They advise attaching one side of a the bridge cable to Armature, leave the other free. Then apply power to F1. Then connect the armature bridge to F2. Then disconnect power and bridge, put power to F2 and then connect bridge to F1.
This apparently isolates components somehow, I didn't follow. When I tried your method, all I could get was a spark on the negative. With their method, even though it looks like it should be identical, my motor works fine in both directions.
Again though, thanks for making the video. super helpful, and got me started down the path to learning that my motor is fine. Keep up the good work.
Clear concise and no stuttering, good informative vid. just what i needed. thanks
Just got one from my buddy had no idea how to wire it but this video helps 👍👍
Thanks for the tips!!! I just bought an old warn m8000 for $80 and made sure it worked using your video.
B
Enrique Reacher seen all day long is the first time I've seen a video that I could understand
Very concise and well explained procedure.
Thanks for taking the time to make this quick, informative video.
Mmmlml
Awesome, bump for part three. Have an M1200 that I have to tap on the solenoid box to get it to operate half the time. Also just got a used industrial 15k that I need to go through and build a control pack for.
@spsingam Try using penetrating oil on the shaft the clutch knob is connected to. A lot of times there is corrosion between the shaft and case which prevents you from pulling the knob out all the way. Next step after that is to remove the two bolts that holds the clutch assembly to the housing and carefully remove it. Ensure that it is indeed sliding in all the way then reinstall.
I don't own a Warn winch I own what is probably a cheap Chinese copy. My solenoid box for the winch controller rusted out after only a few years and it let me down on the trail when I need it. I rebuilt the solenoids with new parts and I put a bunch of Dielectric grease on it. After thinking of ways to waterproof the controls I decided to pack the whole controller box full of grease. I'm hoping that this works longer than nothing but I won't know for another year too feel free to comment what you think
I like the dielectric grease idea and use a lot of it in connectors, but I mounted my solenoids unde the lid of an ammo can away from my winch (they don't need to be next to it, that's for manufacturer and installation convenience) . The lid flips open and I have total access to noids and wiring. I use welding cable and lugs to make custom cables. The lid and solenoids are removable as a unit by sliding the lid hinge laterally like any other ammo can.
Wanted to see the basics of winch wiring. For some reason no one can make it clear to me. Thanks.
First thought is main power wires are hooked up wrong. If you are unsure do NOT attempt to run winch anymore. If you know the main ground and power is hooked up correctly then go to the solenoids, do you hear it click in either direction?
Thanks for the vid ! Really helped me troubleshoot same issue with my winch !
@CATERPILLAR414 Heck no, I have another M8000 that works great, a 9.5XP I'm scabbing parts off of and two 8274s I'm rebuilding. This other M8000 belongs to a friend.
Thanks bro I tried this on a midnight series winch and it was the same process
Where’s part two at ?
Any Bow motors fit in the Warn 8000?
I just get sparks when I apply positive to the open post. bad motor?
GusgusA1 does it try to spin while it is sparking? Try using a multimeter to check for continuity between the posts
@@vantagetes no sir, I left it on fir a second and got some smoke. That's a dead short and a bad motor correct?
@@vantagetes which posts would I check continuity for?
GusgusA1 between A (ground) and F1 or F2 (positive)
@@vantagetes f1 f2 do not have continuity with the ground post until they are jumped with the other top post.
can you by pass the solenoid and hook up switch . and if so can you help me .
Hello I want to connect my winch without a box solenoid.
Can you help me o you hace a diagram.?
You'd spend more on switches than you would on solenoids.
I replaced the solenoid an I here the the solenoid clicking but winch does nothing
josh tesseneer I had that problem on a rew8000 I did allot of power testing and I found this weird wire that runs to both bolts that you connect your power to and in the middle it has a little red pillow shaped thing I think its a fuse but I can't find one. that maybe your problem.
ps its inside with the motor
Superb, it helped me debugging mine!
Very good!
Why didn't you simply use a red cable.
👍 I wonder what gauge wire he using
Good Clip - thanks for sharing ! i got an old Warn i think its some 8274 winch. it rolls and unroll ok, but can seem to get the "free wheelling" clutch thing to work.
anyone with ideas ?
Nope. Not a clue
Thank you
@theoman69 You better buy me a coffee when you when then fucker. They aren't that bad there's just four of them so there's lots of wires.
nice jeep
'solenoid' is pronounced: "soul-in-oid"
Nice yob
As much as winches run for. Just buy another. Or build your own switch. thats what i'd do.
jumpering power lolk
13mm is not it 1/2 inch hi555555555555555555555555555
However most sockets and wrenches are broached so they fit both and any mechanic knows this. 9/16" swaps with 14mm, 7/16" swaps with 11mm etc. 8mm swaps with 5/16" (handy on many electrical nuts and hose clamps).