my SF-102 controller has a marking the left corner for a fan. nothing happens when i press the down arrow for 6 seconds. When i press SET for 6 seconds i get it show PA and that lets me go from 0-100. Do i need to change the module?
Is there a setting to trigger a defrost cycle when the evaporator sees a particular temperature? Or is the only defrost option a timed interval? Also, where does the temp. hysteresis lie with respect to the cold room temperature? OR asked another way does the cold room set point fall at the bottom, middle, or top of the temp. hysteresis range?
Hi mine doesn’t change the paremeters when I click the arrows? Just makes a noise but doesn’t move up or down? PleeAse help this is a big problem for me
Hi, I followed your video and set the settings given. My fridge is set at 03 but screen says 17 and won’t budge either way? Am I doing something wrong??
Hello Andrew, thank you for reaching out to us! Here are a couple solutions for you to try: - The unit could be in defrost mode; if the red dot is between both numbers it’s in defrost mode. - If the red dot is on the left hand side of the two numbers and solid (not flashing), it’s in cooling mode. If the unit is in cooling mode and the temperature is not dropping, a refrigeration technician will be required to fix it. We hope this helps you, but if you have any further questions contact Hilary Dasouza at hilary.dsouza@omcan.com and our call service is always available at 1-800-465-0234. Thank you!
Hello Matthew! We can solve this issue without a problem! Please email Hilary Dasouza at hilary.dsouza@omcan.com who will help you. Again, our call service is always available at 1-800-465-0234. We hope this solves any problems you are having. Thank you
Hey, thank you for the video. I have a few display cases with this control module and the cases once powered on will have the fans running continuously even when the compressor is not working. Is there a way to set it so that the fans only turn on once the compressor turns on?
Press the set button and see what the temperature is set for and if its set to your desired temperature you will have to call a service company to come and inspect
You will have to go into the parameters by holding down the arrow down key for about 5 seconds until ON appears and then press and hold the set button for 5 seconds , then you should be able to change the parameters E1/E2
question on the setting you said. e3 is that 4 degrees in Celsius or Fahrenheit? on the f3 the defrost termination temp. you said 12 degrees. was that in Celsius or Fahrenheit? thanks for the great video!
Hi Travis sorry for the late reply.....E3 is in Celsius which is set for 4 and F3 is set for 12 which is in Celsius as well . Once you change C1 to 1 which is Fahrenheit and then you go back into the parameters , everything will be in Fahrenheit . Hope this helps and thank you for the great question
E3 will be set in Celsius which 4 and you can modify the differential if that’s too low . F3 defrost termination temperature is in Celsius as well which is set for 12 and glad we can be of an assistance.
How to set for a refrigerator? I got a refrigerator that they convert from a freezer to refrigerator and now the temperature is cool at 60 Degree I can't set up for 38 degree. Thank you very much.
Great video. Mine has a constant beep coming out of it. It’s loud and it will not stop. Any suggestions? Please help. Thanks in advance ! It’s on a prep table.
Hi Mahesh! Our Sf-102's have an input of 120v AC and and output of 12v AC. I hope this answers your question but you need further assistance our call service is always available at 1-800-465-0234. Thank you
Hi Bradley, I have an SF-104 in a beer fridge that does the same thing and displays "PA". Have you managed to get beyond the "PA"? If so, how did you do this?
Hi.. do you know what he did? I can't change the values in e1 and e2. If i press arrow down for 5 sec starts a supercooling mode. I don't know how to unlock to change e1 and e2
@@glaucoqs hello sir. How do I get past the password? Once I set it to 00, it just takes me back to the home screen. Never lets me in past the PAS. I have the down arrow setting to OFF, so that's not the problem. Thanks for your advice
Factory default revision: Press SET button to adjust set temperature well. Press button SET for 6 seconds to enter parameter setup mode to set the parameter and then press SET button again for 6 seconds, COP will be displayed, the stored and revised set temperature and parameter are factory default.for factory default resumption: press UP button and DOWN button simultaneously for 6 seconds, 889flashes, all parameters will be resumed as same as factory defaults. After 6 seconds, it returns to normal operation
my SF-102 controller has a marking the left corner for a fan. nothing happens when i press the down arrow for 6 seconds. When i press SET for 6 seconds i get it show PA and that lets me go from 0-100. Do i need to change the module?
Running a red bull fridge. What is ideal for my setting? Right now showing 07 on main screen. What exactly is that number? Thanks
Can the speed of the fan be set? thank you
Is there a setting to trigger a defrost cycle when the evaporator sees a particular temperature? Or is the only defrost option a timed interval? Also, where does the temp. hysteresis lie with respect to the cold room temperature? OR asked another way does the cold room set point fall at the bottom, middle, or top of the temp. hysteresis range?
Can you please help with setting a SF-203 controller?
I can't change e1~e2, and if i press arrow down for 5sec starts a supercooling "SC" mode. How can i unlock to change e1~e2?
Left little light is sold. The little light between the numbers is flashing. Temp showing 18C. But it should be around 4C though, right?
Hi mine doesn’t change the paremeters when I click the arrows? Just makes a noise but doesn’t move up or down? PleeAse help this is a big problem for me
Hi, I followed your video and set the settings given. My fridge is set at 03 but screen says 17 and won’t budge either way? Am I doing something wrong??
Hello Andrew, thank you for reaching out to us! Here are a couple solutions for you to try:
- The unit could be in defrost mode; if the red dot is between both numbers it’s in defrost mode.
- If the red dot is on the left hand side of the two numbers and solid (not flashing), it’s in cooling mode. If the unit is in cooling mode and the temperature is not dropping, a refrigeration technician will be required to fix it.
We hope this helps you, but if you have any further questions contact Hilary Dasouza at hilary.dsouza@omcan.com and our call service is always available at 1-800-465-0234.
Thank you!
Hello, I have questions. Need help
How to activate deffoger of front glass.
how to turn it off without unplugging?
My unit display is switching between the temp and PA, and beeping as well. Any clue how to stop this?
Hello Matthew! We can solve this issue without a problem! Please email Hilary Dasouza at hilary.dsouza@omcan.com who will help you. Again, our call service is always available at 1-800-465-0234. We hope this solves any problems you are having.
Thank you
Hey, thank you for the video. I have a few display cases with this control module and the cases once powered on will have the fans running continuously even when the compressor is not working. Is there a way to set it so that the fans only turn on once the compressor turns on?
Appreciate your inquiry! For any questions or further information, please don't hesitate to reach out to our dedicated team at sales@omcan.com. Thanks
Hi can you help
My chiller temperature is 23.6 and its not cooling at all.. it was working fine untill yesterday...
Press the set button and see what the temperature is set for and if its set to your desired temperature you will have to call a service company to come and inspect
Thanks for your explanation, it help a lot. Just asking, how about to calibrate the sensor, is there a way to do that?
Appreciate your inquiry! For any questions or further information, please don't hesitate to reach out to our dedicated team at sales@omcan.com. Thanks
I cant modify neither e1 nor e2 parameters. They just stay at 0 Celsius and 6 Celsius respectively. I dont know what else should i do
You will have to go into the parameters by holding down the arrow down key for about 5 seconds until ON appears and then press and hold the set button for 5 seconds , then you should be able to change the parameters E1/E2
question on the setting you said. e3 is that 4 degrees in Celsius or Fahrenheit? on the f3 the defrost termination temp. you said 12 degrees. was that in Celsius or Fahrenheit? thanks for the great video!
Hi Travis sorry for the late reply.....E3 is in Celsius which is set for 4 and F3 is set for 12 which is in Celsius as well . Once you change C1 to 1 which is Fahrenheit and then you go back into the parameters , everything will be in Fahrenheit . Hope this helps and thank you for the great question
E3 will be set in Celsius which 4 and you can modify the differential if that’s too low . F3 defrost termination temperature is in Celsius as well which is set for 12 and glad we can be of an assistance.
How to set for a refrigerator? I got a refrigerator that they convert from a freezer to refrigerator and now the temperature is cool at 60 Degree I can't set up for 38 degree. Thank you very much.
Great video. Mine has a constant beep coming out of it. It’s loud and it will not stop. Any suggestions? Please help. Thanks in advance ! It’s on a prep table.
On the controller does it have error code ex. EE1 , EE2 ?
Omcan no it doesn’t. It just displays the actual temperature inside the prep table. Thanks for the response!
@@MrEltinieblas If no error code appears then controller will need to be replaced.
Omcan I understand. Thanks again!
Mine is beeping and showing on off signs. Doesn't show temperature or any error code. Any suggestions?
Can you please show how to connect back wire ...whether DC or AC
Hi Mahesh! Our Sf-102's have an input of 120v AC and and output of 12v AC. I hope this answers your question but you need further assistance our call service is always available at 1-800-465-0234.
Thank you
You try to give the video more brightness it will be great if you do
What is the top right button for? Defrost temp, I think. Mine says 18C.
Debiera estar traducido al español
What’s wrong when it shows LL?
Appreciate your inquiry! For any questions or further information, please don't hesitate to reach out to our dedicated team at sales@omcan.com. Thanks
I guess I have a slightly different model because mine showed “PA” first before E1.
Hi Bradley, I have an SF-104 in a beer fridge that does the same thing and displays "PA". Have you managed to get beyond the "PA"? If so, how did you do this?
@@stephenstreet5200 I had to get a workman in. He unblocked a blockage and Re gassed it. All good now.
Hi.. do you know what he did? I can't change the values in e1 and e2. If i press arrow down for 5 sec starts a supercooling mode. I don't know how to unlock to change e1 and e2
Hi.. PA is password.. you have 0 to 99 chances.. after password, the controller shows parameters!
@@glaucoqs hello sir. How do I get past the password? Once I set it to 00, it just takes me back to the home screen. Never lets me in past the PAS. I have the down arrow setting to OFF, so that's not the problem. Thanks for your advice
Please in Spanish who can explain me help
Hi Dany..it would be best to contact us at 1-800-465-0234 and someone might be able to help you regarding your request.
My digital controller screen always displays E22.... can u help me please ?
Hi I would recommend calling us at 1-800-465-0234. A rep will be able to assist.
Omcan srry it is EE2
@@victorcruzfuentes9587 Hello did you find out what EE2 means ?
Panos Moraitis no I didn’t
@@victorcruzfuentes9587 I found it: Open circuit or short circuit of defrosting probe
how to make a factory reset?
Factory default revision: Press SET button to adjust set temperature well. Press button SET for 6 seconds to enter parameter setup mode to set the parameter and then press SET button again for 6 seconds, COP will be displayed, the stored and revised set temperature and parameter are factory default.for factory default resumption: press UP button and DOWN button simultaneously for 6 seconds, 889flashes, all parameters will be resumed as same as factory defaults. After 6 seconds, it returns to normal operation
Español por favor
Esta de webos pero los subtítulos hasta el qlo xd.
Bad Video - Your Hand is Covering the complete viewing