Thanks for the input. But it would be so nice to make a complementary circuit to this which allows to protect the pump when the system is without water.
Circuit update: I made this circuit by watching this video but there were two errors coming: problem 1: motor was off during the water level and turned on when water level touched all top position(red) wire. solution : don't connect the wire on nc terminal connect it on "NO" terminal problem 2: after the modification motor gets on when water goes just below top level (red) wire. solution : I exchanged blue wire with red wire and the circuit worked fine
Thanks but I have two questions : I used 9v battery and it drains easily what can I do . secondly my relay keep smoking when connected to my 1hp submersible pump what can I do . plz advice
Good work. I will try myself. I have to use it with 5V supply only since I have a 5V USB adaptor and a 5V relay module. What will need to be changed or modified in the circuit if using such a 5V relay module? I have another question: I wish to show an LED light up for 5% level. How to do this? Also, when the level is below 5%, how can I attach another LED to glow (indicating level below 5%) so that when the water reaches 5% level sensor, this LED (below 5%) stops glowing but the 5% LED starts glowing? Can I also use the 5% LED as a flashing one and how? Hoping to hear from you soon.
Peace, mercy and blessings of God be upon you. Operating a home pump project through three or several levels to operate the pump and stop it automatically.
Dear author, could you please make a video in which to show how to assemble a simple transformerless power supply to power this circuit from a 220 volt alternating current. Thanks for the video!
Leds and the rest don't take much, the relay will determine that, I would say 100mA above the relay consumption, and normally relays are between 100 -300 mA
Да такую же схему собрать, только логику поменять на обратную: сухие контакты - реле размыкается. И два реле в последовательную цепь на одну помпу. Это если в лоб.
For lab tests it's good but it's not practical, you can't use DC inside water, you will end up cleaning the terminals every week....you need to use AC inside the water instead
السلام عليكم اخي ممكن ربط المتحسس بااربعة مستويات تبدا بالصفر وتنتهي بالمئة طوافة مقسمة لاكثر من مستوى لو سمحت وتشرح طريقة الربط لو سمحت اخي العزيز لتحكم بمضخة المنزل تشتغل وتتوقف بالاردوينو بابسط صورة ارجو الاجابة باسرع وقت
भाई यदि आपने बाना कर प्रक्टिकल कर लिया है तो इसे सबको बताना अन्यथा किसी को मत बताना क्योकि जब आदमी पैसा भी खर्च करे और समय भी जब सफलता हाथ नही लगती है तो दिल से माँ बहन के लिये गालियाँ निकल तीं हैं भाई हकीकत मै है तो अपना वाटसप नम्बार दो फिर मै आपको बहुत सर्किट जो कि प्रक्टिकल करके देख लिये है धन्यवद 🙏🇮🇳🌺🙏🇮🇳🌹🌺🙏🇮🇳🌹🌺🇮🇳
it is not working with 0.5 or 1 H.P motor .... that's really necessary.I did it and all system burned. such demo projects only with very small DC motors.Dont make foolish to your subscribers.
Thanks for uploading this useful circuit. You're an awesome guy.
Muchísimas gracias , un saludo de Galicia , Vigo
Incredible. So many uses. Thanks
Fantastic🤘😝🤘 bhai love ❤❤❤from odisha
Very good effort and you wish to share others also. Thank you🙏🙏🙏🙏🌹🌹🌹🌹
💯 Sensacional 👏👏👏👏👏
Gosto muito de eletrônica
Parabéns você show 👍
Super. Simple et utile. Merci
Thanks for the input. But it would be so nice to make a complementary circuit to this which allows to protect the pump when the system is without water.
No
what if some short circuit leaks the current through wire to the water ? is there any safety for that ? I dont think so right ?
Circuit update:
I made this circuit by watching this video but there were two errors coming:
problem 1: motor was off during the water level and turned on when water level touched all top position(red) wire.
solution : don't connect the wire on nc terminal connect it on "NO" terminal
problem 2: after the modification motor gets on when water goes just below top level (red) wire.
solution : I exchanged blue wire with red wire and the circuit worked fine
Tank you. Nice. Im from Poland.
Great!!! Thank you my boy! João from Brazil!
Welcome
Can it to pump 220 volt?
@@saidtv2710 Yes
hi. i tried to do this using a breadboard and arduino uno for a class project. it was a fail! thanks for the video and i'll keep trying
Thank you! Regards from Reynosa, México
Sir same circuit 24 v dc relay main capisitor aur transitor kis no ke use krne h
Thank you sir bht khooob.
Kia AC 220v 1HP ki moter use kr sakty hen is pe?
boa tarde muito simples e bem bolado parabens mais seria interesante se dece de por 3 leds indicadores
Thanks but I have two questions : I used 9v battery and it drains easily what can I do . secondly my relay keep smoking when connected to my 1hp submersible pump what can I do . plz advice
Serve para 110vlts???
Guys very IMPORTANT NOTE if your 100 omh is burning or getting crazy hot then try
10K resistor.
It will work
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
The world's best teacher thanks
Can i get a circuit diagram of this ?
Just one question why do you only show the schematics for 2 seconds
Hello, is it possible to make an electronic circuit for an inverted water pump? For example, the bucket will fill with rain and empty automatically
Agar really or circuit ko 12 volt supply pr use krna ho to kia changing Karni Hogi?
I wanted this type video. everyone making this circuit using PCB. This video is best
Excellent, just what I need
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
Where are you from india? I mean which state
Good work. I will try myself. I have to use it with 5V supply only since I have a 5V USB adaptor and a 5V relay module. What will need to be changed or modified in the circuit if using such a 5V relay module?
I have another question: I wish to show an LED light up for 5% level. How to do this? Also, when the level is below 5%, how can I attach another LED to glow (indicating level below 5%) so that when the water reaches 5% level sensor, this LED (below 5%) stops glowing but the 5% LED starts glowing? Can I also use the 5% LED as a flashing one and how?
Hoping to hear from you soon.
You can do it with a diode and a relay only ,
3:35 The thick wire is for AC 220v?
Please building the case ! Safety is number one prioryty ! ❤❤❤❤❤
👍
In put supply given by 12v DC supply was supported this circuit...
Hi pro you can make very good👍👍👍👍
Çok zekice.
This is very wise.
Sir apne supply se kase jorte h wo nhi dikhaya
Does the circuit is working or not
How much power suppy give this circuit ?
Great work! Like
😊
Nice design- recommend for to add sensing foot valve level also along with this.. so this will become also safety for pumb motor.
Good . But could you plz tell us what voltage you used to power the circuit. Can I use a 9v battery ?
It shows 6V to the left of pin 4. It should work on 9V, too -- but relay specs and battery life should be considered.
I like this and I need it
Just one question current flow in tank outlet yes or no.please experience me and current flow in tank outlet which volts.
No current flow as it is dc operated ac switching circuit
When motor starts relay can not tolerate more than 10A..
What we have to do for this??
powar kine volt a
Peace, mercy and blessings of God be upon you. Operating a home pump project through three or several levels to operate the pump and stop it automatically.
Mantap sahabat ku sukses selalu
By inserting electrodes in water would there be any electrolysis effect?
Slightly
Sir, pani line me aate hi pump chalu ho Jaye, aur pani bangh ho ne per pump bandg ho haye aisi circuit banaiye, thanks.
Instead of supply line, make ground line pin 1 common, interchange 2 & 6 and use pin 7 to operate relay
Hi. Pls, where to connect dry run protection ? What are the modifications to do ?
How to add water pump dry protection when water tank source is empty,help me sir
what's the power source ???
Wooooooohooo
It work properly thanks 😊
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
Working karegaa yaa nhii jldi batao please
If I connect to the aquarium, will the fish swim belly up?
🤣
I made the circuit. But when the motor starts the base register of bc547 and 555 ic gets very hot. What to do ?????
Hi, is there any protection if pump failed to deliver the water
There are many protection which can be applied .Pressure switch or flow switch etc etc .
please tell me, how can this be used to control a 220V 1 horse power motor/pump...? what more is needed?
Use the same relay, 10A 250VAC. 1hp draws less than 5A at 220VAC
Just check the start-up current does not exceed 10A
Dear author, could you please make a video in which to show how to assemble a simple transformerless power supply to power this circuit from a 220 volt alternating current. Thanks for the video!
Transformerless power supply doesn't have insulation from the main's. So that can't be use in this project
@@TechIdeasAG Then what kind of small-sized power supply can be used in this project?
Nice
Anything to change if I have 12V supply ??? Thank's
You can use 12v dc without any modification
Douse it will work 9n 240 volt Ac Moter also 🙄
❤❤👌👌👍👍
Is it works in AC current?
my question as well ...
Kis par chalyah hai Ac par yah Dc par.
DC
Sensor wire kitna meter se kam karega
70 to 100 Mtr. Depends on wire gauge
Circuit ka daigram kaha hai vo chahiye
What type of powerful relay use for 1 hp ac pump motor set. Give the full information.
Use 12V 10Amp realy
@@bhagyashreeghugare8381 ma'am i used 12 v 30 amps relay still hissing sound is comming after tank full because supply is on
@@bbiswasable use capacitor
How many milliamps does this circuit require?
Leds and the rest don't take much, the relay will determine that, I would say 100mA above the relay consumption, and normally relays are between 100 -300 mA
Can i use 220v AC watar motor???
Yes friend, you can use ac motor also
O relé no esquema eletrico ficou ao contrario.
субтитры сделай . идеи не хватает или башка плохо соображает. ты же для всех делаешь
And materials required
Sir can i get simulation circuit sir
Can any 1 explain me the working principle of this model
Power supply 6v ya 22v
6v
@@TechIdeasAG but here is 110v, what can i do??
Thanks ( Paulo /Brasil)
Tanks
muito legal! vou fazer um também
А если вода в правом сосуде кончилась, а левый еще не наполнился? :=) Конец помпе? :=)
Да такую же схему собрать, только логику поменять на обратную: сухие контакты - реле размыкается.
И два реле в последовательную цепь на одну помпу.
Это если в лоб.
For lab tests it's good but it's not practical, you can't use DC inside water, you will end up cleaning the terminals every week....you need to use AC inside the water instead
Pls video banaye
Please check in metal container
السلام عليكم اخي ممكن ربط المتحسس بااربعة مستويات تبدا بالصفر وتنتهي بالمئة طوافة مقسمة لاكثر من مستوى لو سمحت وتشرح طريقة الربط لو سمحت اخي العزيز لتحكم بمضخة المنزل تشتغل وتتوقف بالاردوينو بابسط صورة ارجو الاجابة باسرع وقت
First like
😊
Working karegaa yaa nhii
When it's applied for use. The person using it while motor is on May get shocked.
Direct 220 AC mey chaley ga
how does it work in reverse? when the water is full the pump turns on, when the water runs out the pump turns off
It's not working sir. When try to connect vcc to pin 8.relay will not switch properly and motor runs continuesly irrespective of water level
This is for DC motor😐
ගොඩක් w
भाई यदि आपने बाना कर प्रक्टिकल कर लिया है तो इसे सबको बताना अन्यथा किसी को मत
बताना क्योकि जब आदमी पैसा भी खर्च करे
और समय भी जब सफलता हाथ नही लगती
है तो दिल से माँ बहन के लिये गालियाँ निकल
तीं हैं भाई हकीकत मै है तो अपना वाटसप
नम्बार दो फिर मै आपको बहुत सर्किट जो कि
प्रक्टिकल करके देख लिये है धन्यवद
🙏🇮🇳🌺🙏🇮🇳🌹🌺🙏🇮🇳🌹🌺🇮🇳
Shi bole
Hlo sir please tell me ki transitor bc548 use kar sakthe h
Yes
বিখ্যাত আইডিয়া ...
Circuit not working
it is not working with 0.5 or 1 H.P motor .... that's really necessary.I did it and all system burned. such demo projects only with very small DC motors.Dont make foolish to your subscribers.
...use a more powerful relay
Please give me pdf for circuit
It's not working I tryed this
Does not work frod
My 3 time' try again this serkit
Circuit diagram at 1:33