Hi bro. My 100 is now running on 6v. So i want to convert that to 12 v. So bro my q. Is do i need to go with rx100 magnet or 135 mag. Because on here you commented that 135 mag will make fluctuations to the crank. So should i opt for 100 magnet or 135 ?
Yamakaze so bro 12v rx100 rr, 12v battery, the same cdi, rx100 12v wire harness. And from my existing 6v coil set just replace the lighting coil to 12 v( i got one genuine 12v old stock lighting coil. Its ok right?). But still confused that the existing 6v magnet works fine ?
the pickup coil or pulsar coil creates a pulse at a particular time, this pulse is used to trigger the cdi to create a spark signal which intern triggers the HT coil to create a high voltage signal which is converted to a spark using the spark
Hi, from only coil plate perspective we only need to change lightening coil to 12v one. We dont need to buy entirely new coil plate? Will 12v light coil fit in place of 6v one?
Sir for those who travel long trip/tour in rx 135 do they need to carry a spare coil plate of source coil,pickup coil and light coil set or is the original fitted is reliable ????????
The coils blow out for a reason, usually bad Wiring is the issue. Most mechanics believe in twisting the wire and applying tape on it. These short/corrode hence the coils go bad, rx had the best ignitions and are bullet proof, my rx 100 was on the factory coil before it was upgraded to allied coil for better lighting. So short answer is no, you don’t need to carry the coil, clutch cable, 2 additional plugs and throttle cable is the max I would carry. If you are traveling over 500-600 kms then I recommend an extra pair of carburetor if yours develops an overflow then the additional carb can help you reach your destination without loosing a lot of fuel. If you are planning on night rides then a pair of HL and TL bulbs will be a good thing to add to the kit.
Sir, I got my rx100's cylinder rebored and I tried to press the piston(with rings installed) inside the cylinder without any lube. Now, there is a straight scoring mark(about an inch)on the top section of the cylinder wall. I could feel it with my nail. What can I do now to remove it? Will re-honing work or can I simply use it? 😢
What is the benifit of conversation from 6v to 12v , does that only helps in lighting Mine is 6v , very hard to find battery , One mecanic put 12v regulator , now its all working , not having any problem till now ,
Vysakh Vincent there are 2 kind of wiring kits, if you have the 12V wiring kit then it will take the RR unit from 135, if it’s a 6V wiring then you need a connector to connect the 135 RR unit. The rx 100 6V has a 3 pin RR unit and Rx100 12 V has a 4 pin RR unit (same as rx 135)
Great video as usual Brother. 1, I have few questions regarding the conversion as I am planning to buy RDD CDI(just the CDI alone) and fix it on my rx100. I heard that it doesn't work with rx100 12v setup which came in later rx100 models so, we had to convert to rx135 setup for it work. Is it true? 2. Or is it simple to buy an rx135 magnet assembly and fix it in, apart from timing it. If we want to go with this approach, I believe we need to change the wiring as well. Sorry, I am all over the place but want to hear from you.
mjshaheed now RDD cdi’s come with connectors for rx 100. If not then it’s a very difficult task, technically you can get away with just changing the coil plate and the magnet, but it might not work as expected since the crank is not balanced to take the additional load of the 135 magnet. It’s better to get the RX 100 cdi or convert the 135 CDI to 100 by changing the connectors if you already have a cdi
Sir, I have just bought a used IL2 12v Magneto and coil assembly. I will be buying 12v RR unit, bulbs and battery. As for the RR unit goes, Minda 12v 3pin RR for rx100 is available. Is it any good? Please reply.
എന്നെ വളരെ അധികം ബുദ്ധിമുട്ടിക്കുന്ന ഒരു കാര്യമാണ് എന്റെ 135 ന്റെ സ്റ്റാർട്ടിങ് trouble.. ഞാൻ വർക്ക് ചെയ്യുന്നത് north india യിലാണ്.. തണുപ്പ്കാലത്ത് രാവിലെ വണ്ടി സ്റ്റാർട്ട് ചെയ്യാൻ ഒരു രക്ഷേം ഇല്ല.. ഒരു 20 കിക്സ് ചെയ്താലും നടക്കില്ല ചിലപ്പോൾ. പിന്നെ ഇറക്കം വിട്ട് ഗിയർ അടിച്ചു സ്റ്റാർട്ട് ചെയ്യണം.. കാർബുറേറ്റർ ക്ലീൻ ചെയ്തു, വാൽവ് ക്ലീൻ ചെയ്തു, spark plug ക്ലീൻ ആണ്, airfilter ക്ലീൻ ആണ്, പിസ്റ്റൺ ന്റെ കാർബൺ ഒക്കെ ക്ലീൻ ചെയ്തു.. അങ്ങിനെ ചെയ്യേണ്ടതൊക്കെ അത്യാവശ്യം ചെയ്തു നോക്കി.. എന്നാലും വണ്ടി തണുത്താൽ പിന്നെ സ്റ്റാർട്ട് ആക്കാൻ ഒരു 10 മിനിറ്റ് എടുക്കും.. സ്റ്റാർട്ട് ആയാൽ പിന്നെ പുലിയാണ്... ഒരു പ്രശ്നോം ഇല്ല.. missing, lag, ഒന്നും ഇല്ല... നോർമൽ കാലാവസ്ഥയിലും കുഴപ്പം ഇല്ല... ദയവു ചെയ്തു എനിക്ക് എന്തെങ്കിലും ഒരു solution പറഞ്ഞു തരണം bro.. . Coil വല്ലോം മാറ്റണമോ?.12 വോൾട് ആകണമോ??.. വേറെ എന്തെങ്കിലും ചെയ്യണമോ?.. പ്ലീസ് reply me fast bro.... contact cheyyan number tharamo?
Dear bro, why can't you change ignition coil of HH Splendor in place of Yamaha, now NGK iridium spark plug cost you Rs 700/- also available, give a feedback,
Hi brother, i have RX100 in which i changed 12V battery and 12V RR unit. Now my question is can i fix new 12V coil plate with stock 4 hole 6V magnet or is it compulsory to change 2 hole 12V magnet also?
Hi Yamakaze, how are you?? I recently restored my bike and 12v conversion is yet to be done. I put on 12v Amp Poweron battery 🔋 for the bike and apart from that my mechanic said we also need RR unit and 2 in 1 buzzer. Will that be all for the 12v conversion or do I need any?? Thanks.
SRT 99 No, it’s clearly answered in the video. If you think just replacing the battery and RR unit will convert it to 12v then it would be super simple, no?
@@Yamakaze I have changed To 12v battery, RR unit and Bulbs and wiring total new... Voltage getting is 12.5 volts, I need 14volts for getting aftermarket led light, my question is can I use rxz coil instead of 135, and do I need to change the magnet also or the old one will work.... Thanks in advance
Bro , need some tech help Is the rr unit of rxg with 4 pin is a direct fit to 89 model rx 100 wiring? Is the lightning coil of rx 135 a direct fit to the 89 model 100's old stator plate? And flasher of hero honda 12 v??
@@Yamakaze Bro for my 89 rx 100 is that cdi kit with stator plate , magneto and associated things direct plug? Mine is old 6 v wiring . If it's a direct plug & play I too wanna buy those. Thank you for sharing your knowledge and help.
rabbi rubiel it’s plug and play, you will get new wiring kit with the kit, if your existing kit is not in bad condition then I suggest that you use the existing wire
@@Yamakaze but OE Lighting Coil is not available nowadays and other which brand you would like to suggest are reliable and durable.Many mechanic don't prefer to fit brand name Swiss as all the component available of this brand is not at all reliable. Yamaha genuine partsOE, or NIippon-India products of Yamaha RX series are not available in my or near by homecity Ranchi. Please suggest about the availability of the said parts in fair price in any of the southern states of India as far as my assumption RX series bikes spares are heavily stocked and are sold in a very expensive price as some sellers can demand any high price, double are more than that. Please help from where it can be bought if the converstion of electrical system 12volt to 6volt putting a new good reliable brand other than Genuine Yamaha Parts12v Lighting Coil instead of getting used 12v L-Coils from second hand market or from a scrapped bike having 12v electrical system. Thanks
Ranjit Singh Manki I have a different take on the parts hoarding issue. I have traveled 70-80 kms to scout for parts. I have one shop on my way to home from office. Even though I know I can buy rare stuff from the shop which is far, it’s not practical to travel that far, and when I go there I buy only the necessary things and not hoard parts like some people do. Now this is enjoyable and makes sense once or twice a year not every time I want to. I spend atleast 2000 rupees fuel and a whole day. So if you look at it, it’s wise to pay something extra for parts which will be delivered to you, at your convenience. Realistically even Yamaha has increased the prices, the silencer which used to cost 1000, now costs 2500. Chan cover which was 600 is 2500. I can’t blame these Internet sellers who travel to remote shops and buy stuff in bulk to make a profit. I know it’s not fair sometimes. 10k for a rx front mudguard is just plain stupid, but people do ask for funny prices at times, there are people who see value in that. Now to answer your question. Swiss is the only brand available here as well. The mechanics are against it because it might blow up in a day. Used coil is the only option then if you are not willing to wait or pay for OE stuff. One of our subscribers from JH had recently converted his rx 100 to 12v he bought the entire rx 100 coil setup from Swiss and installed it on his 100, he is very happy
Sir please 🙏 rx100 pe korke dikhow kya change korna porega kuch somoj ma nahi aa roha hain ,rx100 ka rr unit tu 3 pin wala lakin rx135 ka tu 4 pin hain then rx100 pe 135 ka rr unit kaise lagye ? Plz sir A to Z botadizea na
Ankur Borah the new wiring loom for Rx 100 comes with 4 pin connector. Only 3 things apart from all the bulbs needs replacement. Lighting coil(fattest coil), RR unit and battery. At present I don’t have a 6V rx 100. I will make a video once I get one.
@@Yamakaze thanks for the reply, I had already seen the video, it was realy helpfull. My bikes wiring harness all gone can we make a new wiring harness by ourself or should go for new one, of so good quality one is available?
Sujil Ps buying new harness is easier and cheaper. New one is around 500, and available easily. Making one will be fun but sourcing all the connectors and matching the length of each loop will be a pain. OE one was available for 310
I have tried another method which is very simple but not a perfect solution , My rx100 is 1986 model I changed 6v regulator to 12 volte and replaced bulbs for 12v electricity , Everything works good , but battery won't charge enough
@@Yamakazethat's why I told it's not a perfect solution , my indicators and horn didn't worked because of not getting 6v battery , i tried emergency light battery but didn't worked Now it's atleast working , I have 12v coil and wiring kit , I am not converting because, i think let it be stock as it is
the earlier models were 6V, they were converted to 12 v due to unavailability of electrical components and for better lighting and electrical performance
@@Yamakaze if we change the full coil plate with new one which some of the TH-camrs promoted. that coil plate it made in india and the dealer is from Bangalore do you know him ? Or you suggest to change my old coil plate with tha new one please reply
Bro please please make a video of 6 volt to 12 volt conversion of rx 100. It will help a lot of people including me for sure. And also show voltage and ampere reading of before(6 volt one if possible) and after one please. Thank you. Because I have a 1984 Japanese model and I am facing lighting issues due to 6 volt coil. Please make a video of it
aniket tiwari no, the new model rx 135 fat coil won’t fit, you need the old model, if you look at the thumbnail of this video then the fastest coil in the thumbnail is to be used.
Hello sir, Can RX135's magnet flywheel be installed on RX100 I mean, are they of the same size and fit. Secondly, I do want to know if the RX135's charging/lighting coil be used on RX100. Lastly, does RX135's RR unit fit in RX100's chassis, the socket type/size doesnt matter, I'll replace the socket manually. Waiting for your reply. Thankyou in advance! PS you are doing a very great job, you reply to each and every comment even if they are silly ones. Appreciate it, sir! Respect!!🙏🏽
Vinayak Malik yes you can install rx 135 magnet on an rx 100 crank, the rr unit can be fitted on the chassis no problem, if you change the rx 100 coil you will have to get rx 135 coil and CDI as well along with the 135 wiring. Best idea is to just change the lighting/ charging coil and install the rx 135 magnet, the new rx 100 wiring can take a 135 rr unit, I am running a 135 rr unit myself
Hi yamakaze. I had installed 1l5 magnet 12 volt on rx 100 and had changed all the electrical components such as cdi, coilplate,wiring, ht coil,flasher, bulbs, battery, rrunit and horn but mine question is will it run for long period
My RX-100 was converted to 12v in 2012, but the wiring harness has a 3-pin socket for RR unit. I want to replace RR unit. Please tell me how to adapt 4-pin RR unit to the 3-pin socket. Also, can I use Shogun or Access 125 RR unit? I can take care of soldering.
Yamakaze I have a new 12v battery, Bike is running on 6v but sometimes horn comes too low and my mechanic suggested me to convert it to 12v then only our battery will be getting recharged. What is the actual use of 12v conversion does it really help in battery recharge and better lighting??
@@AB-hs9pw consider your system as a bank account, you have 12 Rupees in the account and you withdraw 12, but you also keep adding 12-14 rupee to the account, your average balance is going to be above 12. now consider if you add just 6-7 rupee and your withdrawal is 12 no matter what. I hope your question is answered.
@@Yamakaze 1989 I tried several bulbs, even halogens. Sadly no better results. I actually don't know whether my bike us upgraded or not. I'm second user.
As what my mechanic did by only changing the Rectifier, all bulbs of 6v and battery to 12volt and nothing else he did.Rectifier/Charger of 12v is easily available in Brand Minda&Swiss. If anywhere available OE of Radoot175Excel came in 4speed Gear System manufactured till year as I remember till 2002-3 having the same Rectifier in 12v as of RX100's three pin Connector that is fitted easily in the existing wiring Connector of RX100.If according to to you by replacing the Rectifier of RX 135 the Connector of the wiring of RX100 will not fit on it.As the pin arrangement is different in RX100 & RX135 There is no need change the CDI unit.If anybody wants to replace the CoilPlate assembly for converting in 12v by putting 135's unit magnet should be required to fitted of 135 by removing the riveted plate to reduce the weight of the magnet and put by replacing the wiring, Rectifier and CDI unit.These replacement only required when as I mentioned above putting the entire Coil Plate & Magnet assembly of RX135. Initially we forced to put Swiss brand Rectifier, went off within a day hardly after covering 5o kilometers. After a week Minda brand Rectifier came in stock.Luckly still it is running well since last six months covered 1200 kilometres.As I hardly take ride just for few kilometres only. In rest of the time I use scooter or other bikes.
The world has evolved a lot, the see kinda/swiss wiring kits for 100 come with a 4 pin connector, the 3 pin can be converted into 4 pin as 2 pins in out of the 4 are ground. only changing the rectifier/ bulbs to 12V ones won't cut it, that's the reason why people complain about the rx 100 lighting. As mentioned everything needs to be changed, you cannot convert it to 12 V by replacing the whole coil with 12 V. it will work but you will loose the peppy nature of the 100.
It's really nice I am starting learn about my bike because of you 😘😘😘😘❤️❤️❤️❤️🖤🖤🖤🔩🔧🔩🔧thanks brooo
hafiz mhd thank you
Sir what about the socket of the Rectifier , the RX100 3 pin won't fit to the rx135 Rectifier . please reply , thank you !
you need to create a connector
@@Yamakaze sir that means I should find a 4 pin socket which fits to this and take the ground wire out and connect to the chassis. Am I right?
@@dasinduhewagamage5949did you find any solution for this problem ?
Hi bro. My 100 is now running on 6v. So i want to convert that to 12 v. So bro my q. Is do i need to go with rx100 magnet or 135 mag. Because on here you commented that 135 mag will make fluctuations to the crank.
So should i opt for 100 magnet or 135 ?
Just replace the lighting coil. The later model 100 coil is a direct fit
Yamakaze so bro 12v rx100 rr, 12v battery, the same cdi, rx100 12v wire harness. And from my existing 6v coil set just replace the lighting coil to 12 v( i got one genuine 12v old stock lighting coil. Its ok right?). But still confused that the existing 6v magnet works fine ?
@@nandusuganthan8902 the magnet is strong enough to produce 12 v even with the current lighting coil.
Yamakaze ok brother thanks a lot. Got an overall idea. 👍👍
Bro..can u please explain how the pick up coil works in rx 100 or 135 coz its different from the 4 strokes..pick up and flwheel trigger mark setup
the pickup coil or pulsar coil creates a pulse at a particular time, this pulse is used to trigger the cdi to create a spark signal which intern triggers the HT coil to create a high voltage signal which is converted to a spark using the spark
So the function of pick up coil is to produce strong starting current or does it play other important part in running ?
Hi, from only coil plate perspective we only need to change lightening coil to 12v one. We dont need to buy entirely new coil plate? Will 12v light coil fit in place of 6v one?
Yes
Sir for those who travel long trip/tour in rx 135 do they need to carry a spare coil plate of source coil,pickup coil and light coil set or is the original fitted is reliable ????????
The coils blow out for a reason, usually bad Wiring is the issue. Most mechanics believe in twisting the wire and applying tape on it. These short/corrode hence the coils go bad, rx had the best ignitions and are bullet proof, my rx 100 was on the factory coil before it was upgraded to allied coil for better lighting. So short answer is no, you don’t need to carry the coil, clutch cable, 2 additional plugs and throttle cable is the max I would carry. If you are traveling over 500-600 kms then I recommend an extra pair of carburetor if yours develops an overflow then the additional carb can help you reach your destination without loosing a lot of fuel. If you are planning on night rides then a pair of HL and TL bulbs will be a good thing to add to the kit.
@Yamakaze Thank you sir
Can we downgrade starting coil in rx 135 with that of rx 100.
No, it won’t work. Why would you like to do that? Just curious
Due to non availability of parts in remote areas. Weak current on my yamaha rx135 resulting in starting problem.
@@jacksonpeter4124 135 coil won’t increase the current, just get a splendor OE ht coil. That will increase the spark strength
Thank 🙏. I want to fix on rx 135,as it
Is giving starting problem, which splendor(starting coil) model can we use.??? ✌✌
@@jacksonpeter4124 splendor OE coils are same
Sir, I got my rx100's cylinder rebored and I tried to press the piston(with rings installed) inside the cylinder without any lube. Now, there is a straight scoring mark(about an inch)on the top section of the cylinder wall. I could feel it with my nail. What can I do now to remove it? Will re-honing work or can I simply use it? 😢
Hone it and use it
@@Yamakaze Thank you so much, Sir!
@@allaboutnothing99 👍
What is the benifit of conversation from 6v to 12v , does that only helps in lighting
Mine is 6v , very hard to find battery ,
One mecanic put 12v regulator , now its all working , not having any problem till now ,
Same thing you mentioned, unavailability of battery, bulbs, horn
Is the RR unit of Rx135 is dierect set for Rx100?Any need to change the cdi of Rx100?
Vysakh Vincent there are 2 kind of wiring kits, if you have the 12V wiring kit then it will take the RR unit from 135, if it’s a 6V wiring then you need a connector to connect the 135 RR unit. The rx 100 6V has a 3 pin RR unit and Rx100 12 V has a 4 pin RR unit (same as rx 135)
@@Yamakaze what about cdi
@@vysakhvincent1566 you have to use your old rx 100 CDI, the 135 CDI wont work
What are the parts that need to be changed other than the stator? 🤔
RR unit, battery, relay and all bulbs
@@Yamakaze Thanks for the answer bro 🫡
@@Yamakaze I think the 6 volt ignition coil is sufficient, there is no need to change it. 🤔
Great video as usual Brother.
1, I have few questions regarding the conversion as I am planning to buy RDD CDI(just the CDI alone) and fix it on my rx100. I heard that it doesn't work with rx100 12v setup which came in later rx100 models so, we had to convert to rx135 setup for it work. Is it true?
2. Or is it simple to buy an rx135 magnet assembly and fix it in, apart from timing it. If we want to go with this approach, I believe we need to change the wiring as well.
Sorry, I am all over the place but want to hear from you.
mjshaheed now RDD cdi’s come with connectors for rx 100. If not then it’s a very difficult task, technically you can get away with just changing the coil plate and the magnet, but it might not work as expected since the crank is not balanced to take the additional load of the 135 magnet.
It’s better to get the RX 100 cdi or convert the 135 CDI to 100 by changing the connectors if you already have a cdi
After changing to 12v, Will it affect the engine life of the bike ?
No
Sir my headlight is just like a candle.its a 6v so will the light improve if i install battery or is there a problem with the coil...?
Convert to 12v
Good work. Keep going. Also share some photos post completion of work.
Rajesh Podhanandh I document my builds on team bhp, those have write ups and pics
@@Yamakaze cool
Bro did it solve week spark (yellowish colour).And may it improve in performance and fuel economy.. Thank you
great to know
Sir, I have just bought a used IL2 12v Magneto and coil assembly. I will be buying 12v RR unit, bulbs and battery. As for the RR unit goes, Minda 12v 3pin RR for rx100 is available. Is it any good? Please reply.
Buy libero or crux OE rr unit
@@Yamakaze Thank you, Sir.
@@allaboutnothing99 👍
Bro please help me rx100 rr unit comes with 3 pin socket and 135 rr unit comes with 4 pins how to connect the wiring please tell me bro
2 pins are ground in rx 135
എന്നെ വളരെ അധികം ബുദ്ധിമുട്ടിക്കുന്ന ഒരു കാര്യമാണ് എന്റെ 135 ന്റെ സ്റ്റാർട്ടിങ് trouble.. ഞാൻ വർക്ക് ചെയ്യുന്നത് north india യിലാണ്.. തണുപ്പ്കാലത്ത് രാവിലെ വണ്ടി സ്റ്റാർട്ട് ചെയ്യാൻ ഒരു രക്ഷേം ഇല്ല.. ഒരു 20 കിക്സ് ചെയ്താലും നടക്കില്ല ചിലപ്പോൾ. പിന്നെ ഇറക്കം വിട്ട് ഗിയർ അടിച്ചു സ്റ്റാർട്ട് ചെയ്യണം..
കാർബുറേറ്റർ ക്ലീൻ ചെയ്തു, വാൽവ് ക്ലീൻ ചെയ്തു, spark plug ക്ലീൻ ആണ്, airfilter ക്ലീൻ ആണ്, പിസ്റ്റൺ ന്റെ കാർബൺ ഒക്കെ ക്ലീൻ ചെയ്തു.. അങ്ങിനെ ചെയ്യേണ്ടതൊക്കെ അത്യാവശ്യം ചെയ്തു നോക്കി.. എന്നാലും വണ്ടി തണുത്താൽ പിന്നെ സ്റ്റാർട്ട് ആക്കാൻ ഒരു 10 മിനിറ്റ് എടുക്കും.. സ്റ്റാർട്ട് ആയാൽ പിന്നെ പുലിയാണ്... ഒരു പ്രശ്നോം ഇല്ല.. missing, lag, ഒന്നും ഇല്ല... നോർമൽ കാലാവസ്ഥയിലും കുഴപ്പം ഇല്ല...
ദയവു ചെയ്തു എനിക്ക് എന്തെങ്കിലും ഒരു solution പറഞ്ഞു തരണം bro.. .
Coil വല്ലോം മാറ്റണമോ?.12 വോൾട് ആകണമോ??.. വേറെ എന്തെങ്കിലും ചെയ്യണമോ?.. പ്ലീസ് reply me fast bro.... contact cheyyan number tharamo?
Rxg aano? Air filter remove cheythu onnu start cheyyan noku, tell me the results.
@@Yamakaze rxg alla.. 2003 135 aanu.. next time starting trouble വരുമ്പോൾ ഞാൻ അങ്ങനെ ചെയ്തു നോകാം..
Tommy phebe 👍
Dear bro, why can't you change ignition coil of HH Splendor in place of Yamaha, now NGK iridium spark plug cost you Rs 700/- also available, give a feedback,
Great work
👍
Hi brother, i have RX100 in which i changed 12V battery and 12V RR unit. Now my question is can i fix new 12V coil plate with stock 4 hole 6V magnet or is it compulsory to change 2 hole 12V magnet also?
Magnet needs to be changed
We have to relace rx100 Fat coil into rx135 Fat coil? Right?
Shriyansh Mishra yes that’s correct
@@Yamakaze We have to change the charger and cdi also?
And what will be the total cost?
Shriyansh Mishra if you are referring to the regulator rectifier unit then yes.
@@shriyanshmishra8778 CDI need not change, I have no idea of the costs in your area.
@@Yamakaze Thanks...😊
Thanks bhai
Hi Yamakaze, how are you??
I recently restored my bike and 12v conversion is yet to be done. I put on 12v Amp Poweron battery 🔋 for the bike and apart from that my mechanic said we also need RR unit and 2 in 1 buzzer. Will that be all for the 12v conversion or do I need any??
Thanks.
SRT 99 No, it’s clearly answered in the video. If you think just replacing the battery and RR unit will convert it to 12v then it would be super simple, no?
@@Yamakaze I have changed To 12v battery, RR unit and Bulbs and wiring total new... Voltage getting is 12.5 volts, I need 14volts for getting aftermarket led light, my question is can I use rxz coil instead of 135, and do I need to change the magnet also or the old one will work.... Thanks in advance
Bro , need some tech help
Is the rr unit of rxg with 4 pin is a direct fit to 89 model rx 100 wiring?
Is the lightning coil of rx 135 a direct fit to the 89 model 100's old stator plate?
And flasher of hero honda 12 v??
The answer to first 2 question is no, the last question is yes
@@Yamakaze so how to fix light coil in 100? Any solution?
rabbi rubiel th-cam.com/video/UqtwLei9JLo/w-d-xo.html
@@Yamakaze
Bro for my 89 rx 100 is that cdi kit with stator plate , magneto and associated things direct plug?
Mine is old 6 v wiring . If it's a direct plug & play I too wanna buy those.
Thank you for sharing your knowledge and help.
rabbi rubiel it’s plug and play, you will get new wiring kit with the kit, if your existing kit is not in bad condition then I suggest that you use the existing wire
Bro best video
👍
So you mean sir, we only change the rectifier, a 12 volts rectifier? I'll wait for your answer sir. Thankyou very much
Jhun Bedania no, you have to change the lighting coil, RR unit, flasher unit, battery and all the bulbs.
@@Yamakaze ah ok sir. I thought im not going to change the lighting coil.. Thank you sir...
Jhun Bedania good
@@Yamakaze but OE Lighting Coil is not available nowadays and other which brand you would like to suggest are reliable and durable.Many mechanic don't prefer to fit brand name Swiss as all the component available of this brand is not at all reliable. Yamaha genuine partsOE, or NIippon-India products of Yamaha RX series are not available in my or near by homecity Ranchi. Please suggest about the availability of the said parts in fair price in any of the southern states of India as far as my assumption RX series bikes spares are heavily stocked and are sold in a very expensive price as some sellers can demand any high price, double are more than that. Please help from where it can be bought if the converstion of electrical system 12volt to 6volt putting a new good reliable brand other than Genuine Yamaha Parts12v Lighting Coil instead of getting used 12v L-Coils from second hand market or from a scrapped bike having 12v electrical system. Thanks
Ranjit Singh Manki I have a different take on the parts hoarding issue. I have traveled 70-80 kms to scout for parts. I have one shop on my way to home from office. Even though I know I can buy rare stuff from the shop which is far, it’s not practical to travel that far, and when I go there I buy only the necessary things and not hoard parts like some people do. Now this is enjoyable and makes sense once or twice a year not every time I want to. I spend atleast 2000 rupees fuel and a whole day. So if you look at it, it’s wise to pay something extra for parts which will be delivered to you, at your convenience. Realistically even Yamaha has increased the prices, the silencer which used to cost 1000, now costs 2500. Chan cover which was 600 is 2500. I can’t blame these Internet sellers who travel to remote shops and buy stuff in bulk to make a profit. I know it’s not fair sometimes. 10k for a rx front mudguard is just plain stupid, but people do ask for funny prices at times, there are people who see value in that. Now to answer your question. Swiss is the only brand available here as well. The mechanics are against it because it might blow up in a day. Used coil is the only option then if you are not willing to wait or pay for OE stuff. One of our subscribers from JH had recently converted his rx 100 to 12v he bought the entire rx 100 coil setup from Swiss and installed it on his 100, he is very happy
Sir please 🙏 rx100 pe korke dikhow kya change korna porega kuch somoj ma nahi aa roha hain ,rx100 ka rr unit tu 3 pin wala lakin rx135 ka tu 4 pin hain then rx100 pe 135 ka rr unit kaise lagye ? Plz sir A to Z botadizea na
Ankur Borah the new wiring loom for Rx 100 comes with 4 pin connector. Only 3 things apart from all the bulbs needs replacement. Lighting coil(fattest coil), RR unit and battery. At present I don’t have a 6V rx 100. I will make a video once I get one.
How to start rx 100 after 2 years? Like petrol change oil change carbeurator etc? Make video on that pls
V Abhilash sure. I will make a video on starting my RD which was not started in almost 6 months. Procedure is same
Yamakaze thank you
V Abhilash in case you missed the video, here is the link th-cam.com/video/TkRE8q9XyzM/w-d-xo.html
Rx100 rr unit how use tvs50 battery 🔋 charging
No idea
Hi can I install 1l5 12 volt rx 135 1999 model to rx 100?
No, the ignition timing is different
Hi could you please do a video on rx 100/135 complete re wiring..
Sujil Ps I have already done a wiring video
th-cam.com/video/tIM19SI6fY8/w-d-xo.html
@@Yamakaze thanks for the reply, I had already seen the video, it was realy helpfull. My bikes wiring harness all gone can we make a new wiring harness by ourself or should go for new one, of so good quality one is available?
Sujil Ps buying new harness is easier and cheaper. New one is around 500, and available easily. Making one will be fun but sourcing all the connectors and matching the length of each loop will be a pain. OE one was available for 310
@@Yamakaze Thanks a lot for your reply.. looking forward for your posts..
Brother 6 v to 12 volt convert ചെയ്യുമ്പോൾ വയറിംഗ് മാറ്റണമോ❤
Venda
thanks bro. you mentioned to change the coil, i am assuming it to be 12 volt coil. do you recommend any brand like swiss of nippon?
both are bad, try to get OE
thank you. any part number? or is it shared with any other model - like the one you mentioned about the RR.
@@nischaltopno5746 not sure of the part number get the old rxg type lighting coil, 5 speed bikes have a big coil which won’t fit and clear the magnet
I have tried another method which is very simple but not a perfect solution ,
My rx100 is 1986 model
I changed 6v regulator to 12 volte and replaced bulbs for 12v electricity ,
Everything works good , but battery won't charge enough
If battery won’t charge how is it a solution?
@@Yamakazethat's why I told it's not a perfect solution , my indicators and horn didn't worked because of not getting 6v battery , i tried emergency light battery but didn't worked
Now it's atleast working ,
I have 12v coil and wiring kit , I am not converting because, i think let it be stock as it is
Can we use same cdi and ignition coil from 6volts after converting 6volts to 12 volts ?
Please sir answer, its urgent.
Yes
@@Yamakaze so we need to change only battery, rr unit , flasher and charging coil, right?
Yes
rx100 is already 12v ??
the earlier models were 6V, they were converted to 12 v due to unavailability of electrical components and for better lighting and electrical performance
yes in 1996 Rx 💯 is 12v 1L2 series
Bro if we change from 6v to 12v then the performance will increase?
No, only lighting
@@Yamakaze if we change the full coil plate with new one which some of the TH-camrs promoted. that coil plate it made in india and the dealer is from Bangalore do you know him ? Or you suggest to change my old coil plate with tha new one please reply
@@sarkop848 I have done a video on allied Cdi, watch it
12 volt how many ampair put.
4 amps max
Great
👍
🧐Swizz is bad ?
OE
Is rx 135 lighting coil a full wave coil?
What do you mean by full wave?
@@Yamakaze stock it comes with a halfwave coil, we can convert this coil to a fullwave coil along with a fullwave rectifier
@@dasinduhewagamage5949 technically it should be better, but what is the usage that makes you looking for a full wave system?
@@Yamakaze so that i can fit a fullwave rectifier and make it 12v, beacause I'm from srilanka and we dont have rx 135 lighting coils here for sale
Bro please please make a video of 6 volt to 12 volt conversion of rx 100. It will help a lot of people including me for sure. And also show voltage and ampere reading of before(6 volt one if possible) and after one please. Thank you. Because I have a 1984 Japanese model and I am facing lighting issues due to 6 volt coil. Please make a video of it
aniket tiwari I will but I cannot guarantee when, I don’t have a 6v bike to show you before and after. Mine was converted to 12 V ages ago
Yamakaze can I fit rx 135 lighting coil directly on my old coil plate without any fuzz
aniket tiwari if it’s from an old model reg then yes, new model lighting coil is fat
Yamakaze so you mean fat coil is helpful. Please explain a little bit it would be really helpful
aniket tiwari no, the new model rx 135 fat coil won’t fit, you need the old model, if you look at the thumbnail of this video then the fastest coil in the thumbnail is to be used.
Hello sir,
Can RX135's magnet flywheel be installed on RX100
I mean, are they of the same size and fit.
Secondly, I do want to know if the RX135's charging/lighting coil be used on RX100.
Lastly, does RX135's RR unit fit in RX100's chassis, the socket type/size doesnt matter, I'll replace the socket manually.
Waiting for your reply. Thankyou in advance!
PS you are doing a very great job, you reply to each and every comment even if they are silly ones.
Appreciate it, sir!
Respect!!🙏🏽
Vinayak Malik yes you can install rx 135 magnet on an rx 100 crank, the rr unit can be fitted on the chassis no problem, if you change the rx 100 coil you will have to get rx 135 coil and CDI as well along with the 135 wiring. Best idea is to just change the lighting/ charging coil and install the rx 135 magnet, the new rx 100 wiring can take a 135 rr unit, I am running a 135 rr unit myself
Ok sir, thanks a lot!
@@vmalik2611 welcome
Hi yamakaze. I had installed 1l5 magnet 12 volt on rx 100 and had changed all the electrical components such as cdi, coilplate,wiring, ht coil,flasher, bulbs, battery, rrunit and horn but mine question is will it run for long period
My RX-100 was converted to 12v in 2012, but the wiring harness has a 3-pin socket for RR unit. I want to replace RR unit. Please tell me how to adapt 4-pin RR unit to the 3-pin socket. Also, can I use Shogun or Access 125 RR unit? I can take care of soldering.
Hi,
how much does it cost for 6v to 12v??
Thanks.
Looking at all the parts needed around 2000, With Battery 2000
Yamakaze I have a new 12v battery, Bike is running on 6v but sometimes horn comes too low and my mechanic suggested me to convert it to 12v then only our battery will be getting recharged.
What is the actual use of 12v conversion does it really help in battery recharge and better lighting??
@@AB-hs9pw consider your system as a bank account, you have 12 Rupees in the account and you withdraw 12, but you also keep adding 12-14 rupee to the account, your average balance is going to be above 12. now consider if you add just 6-7 rupee and your withdrawal is 12 no matter what. I hope your question is answered.
Yamakaze 🙏🏻 thank you
@@Yamakaze Can we add battery in Suzuki Max 100 like Suzuki Max 100R. What changes we have to do please answer
What flasher are you using on your RX100
Rx 135
can we use rx100magnet in rx135....
No
@@Yamakaze but sir why
@@Muhammadirfan-cr5zm timing is different for 100 and 135
konsi battery lagai he bike me
12v ya 6v or ah kitna he
saqqu sheikh 12v 3A
@@Yamakaze is it suitable for 30 watt fog lights and big roots horn with some other light items???
saqqu sheikh 5A battery
Sir ji kaam 1 no ka h. Per pls agar vdo hindi me hota to aur best tha.
Koshish karunga
Which bike puller matchs this bike
tech media cd 100, splendor
Thanks brother
Bro 100nta flywheel 35il itta intial power koodo
Ariyilla
Bro i want a engine coil have any idea
No idea
Can i put Yamaha RXZ lightning coil?
Shriyansh Mishra absolutely but you need someone experienced to handle soldering etc
@@Yamakaze ohk...😊 And the magnet will be same na? As of rx100.
@@Yamakaze Can we put any other bike light coil like hero honda or any other?
Shriyansh Mishra yes
Shriyansh Mishra no we cannot put any other bike
Rx100 normal cdi use cheyaamo allenkil athum marano
Same cdi use cheyyanam
What is the benefit of changing 6v to 12v?
Nibin Mathew better lighting mainly, 6v batteries and bulbs are not available easily.
@@Yamakaze That's a great info. No wonder my lights were performing as 'minnaminung'.
Nibin Mathew most of the bikes in Kerala are already upgraded, which year is your bike?
@@Yamakaze 1989 I tried several bulbs, even halogens. Sadly no better results. I actually don't know whether my bike us upgraded or not. I'm second user.
Nibin Mathew check your battery, if it’s 12v then it’s upgraded. Else you will need to upgrade it
Bro show step by step each and everything please 😫🙏🙏💓
And also instruct which coil will be used in place of older one
couple feelings rx 135 coil, it’s in the video. I am planning to work on my rx 100, lighting. I will create a step by step video that time
Ok then also show in that how to install pass switcLH
couple feelings yes, like I mentioned earlier, that’s also planned, I will share that when I am doing my rxz wiring
@@Yamakazebro r u from kerala ples give your contact no
👌🔥
👍
RR unit modification ka video banavo na bhai
naya CDI system le lo, better hai, lighting mast or performance bhi mast
Bro upto which year yamaha rx100 had 6 volt electrical system and from which year it started having 12 volt electrical system
Not sure, I think from early 90s they came in 12v
@@Yamakaze i think 6 volt came upto 1993 and some of 1994 also had 6 volt
As what my mechanic did by only changing the Rectifier, all bulbs of 6v and battery to 12volt and nothing else he did.Rectifier/Charger of 12v is easily available in Brand Minda&Swiss. If anywhere available OE of Radoot175Excel came in 4speed Gear System manufactured till year as I remember till 2002-3 having the same Rectifier in 12v as of RX100's three pin Connector that is fitted easily in the existing wiring Connector of RX100.If according to to you by replacing the Rectifier of RX 135 the Connector of the wiring of RX100 will not fit on it.As the pin arrangement is different in RX100 & RX135 There is no need change the CDI unit.If anybody wants to replace the CoilPlate assembly for converting in 12v by putting 135's unit magnet should be required to fitted of 135 by removing the riveted plate to reduce the weight of the magnet and put by replacing the wiring, Rectifier and CDI unit.These replacement only required when as I mentioned above putting the entire Coil Plate & Magnet assembly of RX135. Initially we forced to put Swiss brand Rectifier, went off within a day hardly after covering 5o kilometers. After a week Minda brand Rectifier came in stock.Luckly still it is running well since last six months covered 1200 kilometres.As I hardly take ride just for few kilometres only. In rest of the time I use scooter or other bikes.
The world has evolved a lot, the see kinda/swiss wiring kits for 100 come with a 4 pin connector, the 3 pin can be converted into 4 pin as 2 pins in out of the 4 are ground. only changing the rectifier/ bulbs to 12V ones won't cut it, that's the reason why people complain about the rx 100 lighting. As mentioned everything needs to be changed, you cannot convert it to 12 V by replacing the whole coil with 12 V. it will work but you will loose the peppy nature of the 100.
sir how about for rs100 yamaha?
as long as its a yamaha 2 stroke and is 6v the process is same
Shukr hai koi pakistani b mila , bhai apka koi num or whatsap ?
?
@@Yamakaze may i have your whats ap or phone nm ?
Instagram only, details in the description
Your videos are all awesome but plz could u talk in Hindi !!
Planning to start a channel, in fact I have a yamakaze Hindi channel
@@Yamakaze do you sell rx parts ?
@@sarangsoni5952 no
I need step by step bro
That’s covered in the allied cdi installation video
3pin rectifiar connection input output connection
Red DC positive, black ground/Negetive, yellow AC phase
@@Yamakaze which terminal red and black and yellow
Hindi language talking
bhai hindi channel subscribe kiya?
Sir how I know whether my yamaha rx 100 is 6 volt or 12 volt
Check all the bulbs, check the rr unit flasher relay, and most importantly the battery. If you don’t have a battery check the rest
Bahi hindi me batao please 🤯😥😫😫
Bhai apko apni boli bolne main koi tkleef hoti hai koi jurmana lgta hai ja shrm aati hai jroor btana...
gulab gill kya bakwas hai, kaun si boli?
Bai hindi me v video hona chaye
ashish pat pingua Bhai I am from Kerala, Hindi is not my mother tongue
@@Yamakaze don't mind understand English it's ok
Ithinte malayam video kude
Cheyyaam
Oooooooobhai plzzzzzzzzzzz hindi me bolo naaaaa
much Hindi nahi aati
English please
Erick john TV English? As far as I remember, this is the English the brits left us with. Unless I am mistaken.