Tertemiz çalışma , gereksiz konuşmalar , bilgiler , müzik yok. İş bitimi parçaların ölçülerine kadar detaylı bilgiler. TH-cam'daki en sevdiğim kanal burası. Ellerinize sağlık .
Without doubt best/easiest/cheapest to make DIY drum sander, I'm making a flat top mandolin and this is just right for my project. Thank you for no nonsense video
Fantastic idea. Definitely added this video to my "make this" woodworking playlist. One suggestion. Since you will need to take the shield off on a regular basis to clean and replace the sandpaper, and since a wood screw can only be removed and installed just so many times before it will no longer hold, I suggest that you use threaded metal inserts in the vertical supports that a machine screw can screw into rather than directly screwing through the shield and into the wood of the support. Then a machine screw with a washer will go through the shield and screw into the insert to hold the shield in place. Since the machine screw is going into the metal threads of the insert rather than directly into the wood, you can take the shield off as many times as you need to clean/replace the sandpaper. The same type of inserts could be used to mount the three vertical blocks in place. This would allow the entire sander to be taken apart and reassembled if needed without compromising the strength and rigidity of the joint between the base and the vertical supports. And a second suggestion. To make the shield stronger and hold its shape, you could take a very thin flexible piece of veneer and use just enough double sided tape to hold it in place on the vertical supports. Then brush the outer surface of the veneer and the ends of the strips in the underside of the shield with wood glue and wrap the shield over the veneer and screw it down. When the glue dries you will have a solid face on both the inner and outer surface of the shield, which will be much stronger than with just the very thin layer on the outer surface. The mounting screws on the supports will help clamp the outer shield to the layer of veneer, but there would be no clamping force in the middle. However, if you made one or two additional vertical supports with the same shape as the two that support the drum and temporarily mount them to the base without the drum in place, that would give you places in the middle where some clamping force can be applied.
It is indeed very good, but don't lower the standard of the video by including superfluous adjectives like 'amazing' - your work doesn't need it and they can be a turn off for some people.
I just finished mine! However, I did make changes. I went with a 5/8 shaft (found some cheap ones on Amazon), the power source is an old angle grinder which spins at 4500 rpm so I added V-belt pulleys to reduce the drum rpm to about 2000 and made the drum width about 20 inches, 3.5 diameter. I still need to add the cover for hooking it up the shop vacuum and another cover to protect myself from the pullies. I've got about 20 end grain boards to the point of needing a surface sander, didn't take long to run two of them "testing" the sander. Big thanks to you Gokmen! I might post a video of mine, I'll be sure and mention your design being the inspiration.
This is 2 things! The best tutorial I have seen on TH-cam And A perfect inexpensive and simple option instead of a $300 planer. Thank you! It’s perfect for what I need!
Very nice, I haven't made one yet because I don't have space in my little shop for another stand alone machine, but this table top model is just right for me.😊 Thank you
Danke Gökmen für diese sehr gute Präsentation, ich verfolge diesen Kanal schon länger, und habe festgestellt das du dich Kamera und Videotechnisch weiter gebildet hast -TOP -das beste ist wie immer die Darstellung, der Baumaße so läßt es sich leicht nachvollziehen -> was da gebaut wird ! Beste Grüße von Bergflitzer Foto Dieter 🤗🎥🎥📷📷🚁🚁
Man you're at it again. You will have to stop embarassing everyone else with your ideas and workmanship. By the way, I built your router lift design. it works incredibly well, thankyou.
I am often dubious about DIY shop power tools but every part made and assembled as demonstrated in this video gives me confidence that this sander can provide a quality outcome in thickness variation across the work piece. Great job. You may want to add some operational information about how much can be removed in a single pass and how to set the removal depth accurately and how to set the drills RPM for optimal sandpaper and drill life. Thanks
Fantastic!!! Of all the homemade thickness sanders I've seen videos for, this is the simplest, yet best working one going. The only thing that could make it better is the addition of some sort of "micrometer" height adjustment and a dial indicator to verify the change in height for real precise thickness sanding. Well done! This is the perfect rig for wood worker hobbyists and model builders...
There is a fairly simple way to accomplish this using those metal thickness gauges. Lift the angled board with the item to be sanded on it up to where it just touches the drum. Then drop and lock both height rods. Now remove the target and put a thickness gauge which is the thickness you want to remove (e.g. 0.02") and put it under one of the rods. Then loosen the other rod and let it drop to the base and tighten it again. Then remove the thickness gauge and loosen that rod, letting it drop to the base and tighten it. Now you've raised the platform approximately 0.02" and when you run the target through it, that is what you will remove. I say approximately because of the angle of the piece and relative position of the rods vs. the drum - but it should be very close.
Vallahi senin bu videolarini donup donup tekrar izliyorum huzur bu islerde izlerken bile kafam dagiliyirsa birde ahsapla ugrassam kendime gelirim heralde eline emegine saglik ustam
Very nice work and video presentation! Here's a tip. After slitting the back of the dust cover, fill the kerfs with glue and saw dust or BONDO and then screw it in place. and let it harden. That will make the curve permanent and easy to remove for changing the sandpaper. Also, send the work through at a slight angle which will distribute the buildup on the drum over a wider area. Pine is gummy and will leave a gum streak on the roller where it will not sand, leaving a ridge on the work.
Very nice project but unfortunately impractical because incomplete: - there's no easy height adjustment (missing is a single knob to allow adjusting the height of the tray) - there's no easy way to replace the sand paper or drum. Other than that, great. Also (a nitpick) a power drill is not meant to run for long times such as is required with a drum sander, consequently it won't last long and hence a dedicated motor makes most sense for this project.
I thought the same thing about sand paper and drum. It would be nice to quickly switch between different grits. I will think about this. And looks like it’s made to for simple purposes. So height and power drill not a problem for me
@@mertcanasfg7986 the height adjustment is a nightmare to get right with just two screws. Have you seen on a planer? You just have one knob and it's easy to chose the height in inches. I don't see how to achieve that on this project and without that it's pretty much unusable for serious work.
Did you watch the sandpaper being added during the video? No disassembly is required because the sandpaper was added after the drum was installed. Remember this is a thickness sander meant to take very small amounts off the thickness of a board and not meant to be a finishing sander. Light passes at a proper speed equals low wear and tear on the sandpaper. If it’s clogging slow down the feed and speed and declog with a natural rubber pad. If your sandpaper is wearing out too quickly change lighten up the single pass removal. Remember this is a simple basic function DIY power tool.
Well, that was absolutely brilliant! So clever… makes me wonder if I could make one wider and with a router instead of a drill. 🧐 I feel so inspired! Thanks!
That’s a good idea. A router would make for a more compact unit which could be permanently mounted 😊. I have a spare one now since I treated myself to nice little palm router. Think I might have a crack at that idea myself. good call Tim.
@@berniebower7891 Good point, but I have three routers, and all have speed control. I’ve never used a drum sander, (it’s on my wish list), so I don’t know how fast they spin. Would a lathe motor work? Mine also has speed control.
Great work. I would modify so that it would be easy to change sand paper. Maybe a dedicated motor as well. With some threaded rods you could adjust thickness easier. Thanks for the idea of the system.
Fun and creative idea, will function in a basic way, but unfortunately will not be precise as things made from wood move, loosen up unequally, deteriorate from vibration. The spinning spool especially you have to be careful about, after a little time of being subjected to such strong rotational forces it may crack, so be careful and maybe inspect/replace at intervals. The drill too is designed to work in quick short bursts with 'rest times', if run continuously like this will probably burn up pretty quickly, motor inside is not designed for continuous operation. Fun stuff to make though.
Rotary hammers are designed for heaven continuous use. Every motor has a reliability that decreases with heat. The trick is to supply a drill that will function over a practical life of ‘normal’ use. Of course normal will be variable. Any drill should me monitored for temperature and use adjusted. As to the vibration issue, plywood is so strong and the vibration from reasonable thickness removal it seems that this wouldn’t be an issue. Remember PT boats and river boats have been in use for almost 100 years of marine design and were and still are plywood constructed.
Brilliant craftsman! Thanks for a video that's pure quality and WITHOUT nonsense. Do you think this simplistic design would work on something larger -- such as a 500mm bed?
Tertemiz çalışma , gereksiz konuşmalar , bilgiler , müzik yok. İş bitimi parçaların ölçülerine kadar detaylı bilgiler. TH-cam'daki en sevdiğim kanal burası. Ellerinize sağlık .
Simple, efficient, functional!
Congratulations on the amazing work!
Greetings from São Paulo capital Brazil.
👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
Вот что значит золотые руки! 👍👍👍
Ты стырил мой комментарий)
Не только руки, но и голова!
Merci beaucoup mon ami pour cette vidéo c’est un plaisir de te retrouver après cette pause et d’apprendre de tes vidéos 👍🙏👍
Excellent video, straight forward, easy to follow and looks to work well!
Thanks from London England 👍💪😎🏴🙏
NO filler! - NO selling! - NO entertainment! --- STRAIGHT forward to the point! -- GREAT one √√√
Brilliantly simple design, thank you for sharing
Without doubt best/easiest/cheapest to make DIY drum sander, I'm making a flat top mandolin and this is just right for my project. Thank you for no nonsense video
Fantastic idea. Definitely added this video to my "make this" woodworking playlist.
One suggestion. Since you will need to take the shield off on a regular basis to clean and replace the sandpaper, and since a wood screw can only be removed and installed just so many times before it will no longer hold, I suggest that you use threaded metal inserts in the vertical supports that a machine screw can screw into rather than directly screwing through the shield and into the wood of the support. Then a machine screw with a washer will go through the shield and screw into the insert to hold the shield in place. Since the machine screw is going into the metal threads of the insert rather than directly into the wood, you can take the shield off as many times as you need to clean/replace the sandpaper.
The same type of inserts could be used to mount the three vertical blocks in place. This would allow the entire sander to be taken apart and reassembled if needed without compromising the strength and rigidity of the joint between the base and the vertical supports.
And a second suggestion. To make the shield stronger and hold its shape, you could take a very thin flexible piece of veneer and use just enough double sided tape to hold it in place on the vertical supports. Then brush the outer surface of the veneer and the ends of the strips in the underside of the shield with wood glue and wrap the shield over the veneer and screw it down. When the glue dries you will have a solid face on both the inner and outer surface of the shield, which will be much stronger than with just the very thin layer on the outer surface. The mounting screws on the supports will help clamp the outer shield to the layer of veneer, but there would be no clamping force in the middle. However, if you made one or two additional vertical supports with the same shape as the two that support the drum and temporarily mount them to the base without the drum in place, that would give you places in the middle where some clamping force can be applied.
This is how a DIY video should've done. Detailed and all necessary pointers were shown. Kudos sir! Thank u for bringing a newbie like me better ideas!
It is indeed very good, but don't lower the standard of the video by including superfluous adjectives like 'amazing' - your work doesn't need it and they can be a turn off for some people.
👍 можно еще сбоку нанести разметку, чтоб оперативно делать толщину для заготовки
Üstadım Elinize emeğinize sağlık, Türkiye'de böyle çalışmalar yapan birinin olmasından çok memnunum. İşiniz gücünüz rast gelsin...
Gerçekten çok güzel bir eser sen bir şahısın eline emeğine sağlık
One of the best projects I have ever seen,perfect job
Thanks, glad you like it 😊
You are an excellent Craftsman !!! Congratulations
Очень умно и продуманно сделанно ! Такая работа заслуживакт похвалы , а Лайк темболее !
I just finished mine! However, I did make changes. I went with a 5/8 shaft (found some cheap ones on Amazon), the power source is an old angle grinder which spins at 4500 rpm so I added V-belt pulleys to reduce the drum rpm to about 2000 and made the drum width about 20 inches, 3.5 diameter. I still need to add the cover for hooking it up the shop vacuum and another cover to protect myself from the pullies. I've got about 20 end grain boards to the point of needing a surface sander, didn't take long to run two of them "testing" the sander. Big thanks to you Gokmen!
I might post a video of mine, I'll be sure and mention your design being the inspiration.
Yes please post a video. looking to upgrade the height adjustment too to be more precise
This is 2 things!
The best tutorial I have seen on TH-cam
And
A perfect inexpensive and simple option instead of a $300 planer.
Thank you! It’s perfect for what I need!
Very nice, I haven't made one yet because I don't have space in my little shop for another stand alone machine, but this table top model is just right for me.😊 Thank you
Excepcional ideia e facilita muito a vida de quem gosta de marcenaria caseira!!! Parabéns!
Отличное видео ,нужный колибровочный станок! Браво!!!
Wow superbe idée, merci mon copain vraiment génial.👌👍
I have been watching your Videos for several Years and you always are got better,keep it up Greetings from Germany
Что автор не сделает,то становится шедевром. Браво.
Просто и доступно! Мне очень нравится! Лайк и подписка.
Bu videolar insani hipnotize ediyor. Saatlerce seyrediyorum. Beynim dinleniyor.
The true pragmatic craftsmanship! Bravo!
Хорошее приспособление. Буду делать, спасибо за размеры деталей.
Severek, titizlikle yapılan iş, Dünya da ses getirir. Selamlar Brüksel'den, Necmeddin PEÇEN
🤲👍
Teşekkürler Necmeddin Bey, Türkiye'den selam ve saygılar.
Another great project, friend. My compliments on the great skills you possess. Thanks for sharing
Çok basit ama kullanışlı oldu. Ellerine sağlık ustam. Videolarınızı daha sık görmek isterim. Özletiyorsunuz
Teşekkürler Ercan Bey, inanın ben de daha fazla video yayınlamak istiyorum ama zamanım ancak bu kadarına yetiyor.
You have a great head and hands! Thanks for your videos!
Beautiful, splendid!!! 👏👏👏 😊👍
Incredible job, as always!
Gökmen = Bilgin Dayı 👍
Great video, thank you for taking the time and effort to show others how to build tools with tools.
Glad you like it. Thanks 😊
Отлично! Возьму на заметку.
Excellente vidéo et bravo pour la qualité du travail 👍👏
Very Nice Work 👍👍👏 Thanks for this video Norbert ( France )
Çok güzel bir zımpara makinası oldu . Ellerine sağlık Gökmen ustam
Nice work--both the sander and the video.
Отлично!!!Просто и надежно!
Thank you very much. Especially for the last 30 seconds!)
GOSTEI MUITO DO SEU VÍDEO A NOTA É TOP 1OOO PARABÉNS 🕵️♀️🤝👍🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
Danke Gökmen für diese sehr gute Präsentation, ich verfolge diesen Kanal schon länger, und habe festgestellt das du dich Kamera und Videotechnisch weiter gebildet hast -TOP -das beste ist wie immer die Darstellung, der Baumaße so läßt es sich leicht nachvollziehen -> was da gebaut wird ! Beste Grüße von Bergflitzer Foto Dieter 🤗🎥🎥📷📷🚁🚁
Vielen Dank 😊
Excelente trabalho, muito criativo. Parabéns pela idéia!
Man you're at it again. You will have to stop embarassing everyone else with your ideas and workmanship. By the way, I built your router lift design. it works incredibly well, thankyou.
Fantastic Idea!!!! Superb!!!
Беларусь смотрит первая!!!
Во сколько полуляхов Беларусь оценит поделку? 😉🤭🤣🤣🤣
Благодарю за труд и за то что делитесь так подробно
Buena maquina, saludos desde Argentina
MUY BUEN PROYECTO, LIKE POSITIVO 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Always amazed me with the build. Good job man
thanks, glad you like it 😊
Großartige Arbeit - sehr effizient - intelligente Lösung - das fertige Teile könnte man kaufen!
I am often dubious about DIY shop power tools but every part made and assembled as demonstrated in this video gives me confidence that this sander can provide a quality outcome in thickness variation across the work piece. Great job. You may want to add some operational information about how much can be removed in a single pass and how to set the removal depth accurately and how to set the drills RPM for optimal sandpaper and drill life. Thanks
Usta ellerine sağlık. Yine güzel bir çalışma olmuş
thank you for the idea🙏 il start using your skills again🙏 God bless you 🙏
Beautiful design that emphasizes form over function. An epitome of minimalist elegance.
Cool build. Thanks for sharing the dimensions
Super machine, beau travail! 👍👏
Fantastic!!! Of all the homemade thickness sanders I've seen videos for, this is the simplest, yet best working one going. The only thing that could make it better is the addition of some sort of "micrometer" height adjustment and a dial indicator to verify the change in height for real precise thickness sanding.
Well done! This is the perfect rig for wood worker hobbyists and model builders...
There is a fairly simple way to accomplish this using those metal thickness gauges. Lift the angled board with the item to be sanded on it up to where it just touches the drum. Then drop and lock both height rods. Now remove the target and put a thickness gauge which is the thickness you want to remove (e.g. 0.02") and put it under one of the rods. Then loosen the other rod and let it drop to the base and tighten it again. Then remove the thickness gauge and loosen that rod, letting it drop to the base and tighten it. Now you've raised the platform approximately 0.02" and when you run the target through it, that is what you will remove. I say approximately because of the angle of the piece and relative position of the rods vs. the drum - but it should be very close.
Bravo majstore! 👍
What an impressively simple and great design! 👍🏻
Congratulations! Beautiful project!
Very nice! I liked your accurate work!
Another great job, both the tool and the excellent presentation (though I'm surprised you did not make the rods and metal brackets from wood).
I need one of those! 😁 nice job
Great work, thanks for sharing.
Yes sir
Simple ,efficace ,super .
Très beau Tito
merci, content que ça te plaise 😊
Excellent video! My bueno! I will be building this as soon as I get back home in my shop. Thanks y gracias
WOW! So simple and effective. Thumbs UP!!
Excellent work! I have seen many on TH-cam but I will make mine like this one. Thank you for the measurements. Blessings.
Did you ever receive the diameter measurement? I seen you commented thank you for the measurements, but I don't see he replied here.
Vallahi senin bu videolarini donup donup tekrar izliyorum huzur bu islerde izlerken bile kafam dagiliyirsa birde ahsapla ugrassam kendime gelirim heralde eline emegine saglik ustam
Smoothing the drum with a reversed drum sander nice!
Mükemmel. Elinize sağlık. Paylaşım için teşekkürler...
marangozlukla mucitliği birleştiren adam, ellerine sağlık
Very nicely done! Great explanation, excellent workmanship! Shukran!
Very nice work and video presentation! Here's a tip. After slitting the back of the dust cover, fill the kerfs with glue and saw dust or BONDO and then screw it in place.
and let it harden. That will make the curve permanent and easy to remove for changing the sandpaper. Also, send the work through at a slight angle which will distribute the buildup on the drum over a wider area. Pine is gummy and will leave a gum streak on the roller where it will not sand, leaving a ridge on the work.
My friend, definitely very useful tips.
Espetacular , parabéns.👏
Very nice project but unfortunately impractical because incomplete:
- there's no easy height adjustment (missing is a single knob to allow adjusting the height of the tray)
- there's no easy way to replace the sand paper or drum.
Other than that, great.
Also (a nitpick) a power drill is not meant to run for long times such as is required with a drum sander, consequently it won't last long and hence a dedicated motor makes most sense for this project.
@@cdunne1620 please provide constructive comments like I do.
I thought the same thing about sand paper and drum. It would be nice to quickly switch between different grits. I will think about this. And looks like it’s made to for simple purposes. So height and power drill not a problem for me
@@mertcanasfg7986 the height adjustment is a nightmare to get right with just two screws.
Have you seen on a planer? You just have one knob and it's easy to chose the height in inches. I don't see how to achieve that on this project and without that it's pretty much unusable for serious work.
Did you watch the sandpaper being added during the video? No disassembly is required because the sandpaper was added after the drum was installed. Remember this is a thickness sander meant to take very small amounts off the thickness of a board and not meant to be a finishing sander. Light passes at a proper speed equals low wear and tear on the sandpaper. If it’s clogging slow down the feed and speed and declog with a natural rubber pad. If your sandpaper is wearing out too quickly change lighten up the single pass removal. Remember this is a simple basic function DIY power tool.
Well, that’s simply pretty damn cool.
Good job on both project and video.
Thanks, glad you like it 😊
Heavily Matthias influenced. Nice job.
Great job 😁👏👏👏
ABSOLUTELY MARVELOUS WORK!!! 👋👋👋
It is a really smart idea!
Well, that was absolutely brilliant! So clever… makes me wonder if I could make one wider and with a router instead of a drill. 🧐 I feel so inspired! Thanks!
That’s a good idea. A router would make for a more compact unit which could be permanently mounted 😊. I have a spare one now since I treated myself to nice little palm router. Think I might have a crack at that idea myself. good call Tim.
Router seems to fast.
@@berniebower7891 Good point, but I have three routers, and all have speed control. I’ve never used a drum sander, (it’s on my wish list), so I don’t know how fast they spin. Would a lathe motor work? Mine also has speed control.
I’m not sure if by slowing down the router you would maintain torque. The lathe motor seems perfect imo.
@@berniebower7891 Class answer!
Thanks for the great video!!!
Screw height adjustment of the table is required instead of pins
Стол лучше винтом регулировать
I can't wait to make this, as I very much need such a device. Thank you so very, very much!
Bellissimo e bravissimo lo copierò, grazie
Meus parabéns grande ideia você e muito zelo
Great work. I would modify so that it would be easy to change sand paper. Maybe a dedicated motor as well. With some threaded rods you could adjust thickness easier. Thanks for the idea of the system.
Yes sir
Beaucoup d’astuces, superbe !👍👍👍
merci, content que ça te plaise 😊
Buen trabajo. Si señor!! 👍
You really are the master
Excelente trabalho.
GOSTEI DA SUA HABILIDADE É SABEDORIA 1000.🕵️♀️🤝👍🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
Fun and creative idea, will function in a basic way, but unfortunately will not be precise as things made from wood move, loosen up unequally, deteriorate from vibration. The spinning spool especially you have to be careful about, after a little time of being subjected to such strong rotational forces it may crack, so be careful and maybe inspect/replace at intervals. The drill too is designed to work in quick short bursts with 'rest times', if run continuously like this will probably burn up pretty quickly, motor inside is not designed for continuous operation. Fun stuff to make though.
Rotary hammers are designed for heaven continuous use. Every motor has a reliability that decreases with heat. The trick is to supply a drill that will function over a practical life of ‘normal’ use. Of course normal will be variable. Any drill should me monitored for temperature and use adjusted. As to the vibration issue, plywood is so strong and the vibration from reasonable thickness removal it seems that this wouldn’t be an issue. Remember PT boats and river boats have been in use for almost 100 years of marine design and were and still are plywood constructed.
Brilliant craftsman! Thanks for a video that's pure quality and WITHOUT nonsense. Do you think this simplistic design would work on something larger -- such as a 500mm bed?
Harika bir çalışma tebrikler elinize emeğinize sağlık cok çok süper çok beğendim