Aluminum Boat REFIT: Painting an Aluminum Boat Doesn't Get Any Easier Than This [Ep. 145]
ฝัง
- เผยแพร่เมื่อ 26 ก.ย. 2024
- In this video, I chat about how to apply bottom paint and a bootstripe to an aluminum boat during our #CUMMINSREPOWER!
Painting Bottom paint on Our #aluminumboat 🖌️: I show you step-by-step how to apply a boot stripe and bottom paint on an aluminum boat.
Adjusting Propellers and Shafts for the Cummins Repower: So many other systems have to be altered to accommodate the new Cummins engines. Watch as we talk about the propellers and shafts and what has to be done to them.
Marking the Anchor Chain: I’ll teach you how to mark your anchor chain with my very own "Janis Marking System", so you always know how much you’ve let out. It makes anchoring safer and easier.
🛠️ Hit that play button to see how we tackle these tasks and others during this extensive Cummins Repower. Whether you're here for tips, tricks, or just love boat content and entertainment, this video has something for everyone.
💬 Got questions or tips?
Drop a comment below! We love hearing from you and try to answer every comment.
👍 If you find this video helpful, don’t forget to like, subscribe, and ring the bell 🛎️ for more boat adventures and maintenance tips.
Your support keeps our channel afloat!
#BoatMaintenance #CumminsRepower #AnchorChain #BoatLife #DIYBoat #SailingTips #bottompaint #aluminumboat
➡️To see where it all began - check out this playlist: • How Blaine And I Met O...
Welcome aboard Tangaroa, where we're gearing up for the adventure of a lifetime!
Join us as we prep our aluminum beauty to set sail for Alaska, Siberia, and Japan. Don't miss out on the excitement! Subscribe now and be part of our journey.
If you want to know more about our boat and us - visit our website www.onboardtan..., and hey, why not become a valued crew member on Patreon?
For just $10 - $25 a month, you'll snag an Official Onboard Tangaroa Challenge Coin and an open invite to hop aboard for bevvies and a visit whenever our paths cross.
Here's what else you get for joining Patreon:
1️⃣ We'll talk to you on Zoom every month, and you'll get a special link in your email! 📆📹
2️⃣ You'll get a special Tangaroa Challenge Coin as a thank you!
3️⃣ You can enter fun contests and win cool prizes!
4️⃣ We'll be really, really thankful because you help us take care of Tangaroa!
Click here to see everything on Patreon: / onboardtangaroa1969
But wait, there's more! We have purchased, tested and reviewed quite a few products during our live onboard Tangaroa. Check out our storefront here to see what we recommend:
kit.co/onboard...
To keep up with our adventure, follow us on Facebook! 📢👍 Join us here: / onboardtangaroa
And here: / onboardtangaroa
Our big journey is coming! We'll go all around places like Alaska, Japan, and more! It's going to be awesome and we encourage everyone to come along for the ride.
From Blaine, Janis, Josh, Izzie, and Maggie the #boatdog
Listen to our cool music here: share.epidemic...
And make your social media awesome with Smarterqueue! Try it here: smarterqueue.c... 🚀
#trawlerlife #boatlife #boatrefit #aluminumboat #aluminumtrawler #liveaboard #boatlife
![WHY Our Lithium Battery Bank needed to be MOVED [Ep. 143]](http://i.ytimg.com/vi/bhGnkfOyeDs/mqdefault.jpg)
![[Full Episode] The Restaurant War Thailand ศึกพ่อค้าซ่าแม่ค้าแซ่บ Episode 1 | 22 ก.ย. 67](http://i.ytimg.com/vi/BuzQ70v-UZQ/mqdefault.jpg)
If you have any questions or comments about what we are doing - make them. Blaine tries to answer every one of them over coffee in the morning. It's kinda his thing and I personally think he enjoys it! So please keep him happy and make a comment.
Janis, You're a Rock Star.
I wish I was there to assist you guys
She is a Rock Star indeed! I lucked out with that one. Janis says she wishes you guys were here to help as well 😁.
Wow. This is a huge project. Bravo.
It was definitely an undertaking! Thanks for watching!
Just watch the video where you answered questions. Blaine is amazing. You guys are great
Thanks so much! We are a good team.
Janis, you're a beast. I don't think I can do a coat on my 41' boat in 4 hours. Props to you for handing the bottom job, it's a tough gig!
She is an absolute beast!
With the new engines, less weight , less barnacles etc the boat is gunna feel brand new again. Great idea marking the chain. Looking great guys.
Oh man we are going to be cruising!
When I stumbled onto your Channel I had to look closer at your Tangaroa ,as 40 years ago I knew a guy in Northland New Zealand who had a Steel fishing boat called Tangaroa, but his was only 3/4 the length of yours and was a former South island Crayfish boat.
When we chose the name we noticed there were a handful of other vessels with this name including some pretty interesting larger ships most of which are from the New Zealand area (for obvious reasons). I had to google crayfish boat. Kind of nice looking layout. Thanks for watching!
That Boat is a lot of work.!!!!!!!!
Yes indeed! We enjoy it at most times though. Thanks for watching!
Great video as usual . .
Hope your opp went well Janis .
And a great effort on the painting . Looking fab . .
Till next time take care .
Bye from NZ👋🍻🇳🇿twa
Thanks! Janis did well with the operation and is mending nicely. She just has to work on minimizing scarring now. She did a great job on the paintwork and I will pass on the comment for sure. Take care!
@@OnboardTangaroa by the way . . The Warning has put out a new album . . Pretty heavy . Ya mite like to check it out . . 👍🍻🇳🇿
Will do!
Wow I want it. That’s bad ass boat! I like the aluminum.
We love it. A lot of work but pretty awesome. Thanks for watching!
Thankyou 😊
You’re welcome 😊
Thanks Guys for the Video I found it very interesting. Stay safe no hospital runs. B
Thanks for watching Bruce! We are looking forward to getting back over there.
Question about the engines. Do you have to add more ballast to the boat to compensate for the engines being lighter? Your definitely not scared or hard work 🍻
We have definitely been mulling over options. The boat is not very tall so there isn't a lot of weight up high. She is inherently fairly stable. It also helps to have all of the tankage built into the bottom of the hull. My current thought on ballast is to build a few seawater ballast tanks down in the engine room below the generators. That way we can pump in water for ballast when we are light on fuel or empty it when we are full of fuel or want to run light. The weight removed with the engines is basically the same weight as one of our three keel tanks when full. It likely wont have a great impact but I am planning options regardless. We are a little bit crazy with what we take on. The repower was definitely more work than originally anticipated but that was anticipated 🤣. Thanks for watching!
While applying alodine. After rinsing run an even sheet of water over the treated area. What you are looking for is a break free sheet of water. Any where the water parts and runs around, retreat that area until the water sheets evenly over the area.
Thanks for the tip! Next time we are applying some we will give it a go.
@OnboardTangaroa I have never painted a boat however, I have painted a lot of naval aircraft 😉
Those are MUCH BIGGER. I would not want to paint a naval aircraft. I think I'll stick to Tangaroa.
J
Your guys boat has an odd hull design. The stern really over hangs past the wheels. Do you get a lot of rumbling through the aft section of the hull. The big flat section would give you a lot of speed in calm water. Osborne has been around for decades. The problem when you run a large diameter wheel on long prop shafts you get the snap back. Believe it or not the shaft twists especially stainless shafts. You can break off coupler bolts. It looks like your boat has 2.5 inch shafts. Designing wheels is a science for sure they can make them for pulling power but you lose speed. Ones designed for speed don't have the thrust for towing. Osborne will set you guys up right. For your desired cruise speed and keep the Cummins at 1200-1300 rpm continous. I imagine you guys are after fuel economy. You can have the power when you are bucking tide or out run bad weather. Somebody is a brave lady painting the interprotect without a mask on. The smell of that stuff damn near killed me. I mixed one batch nope not using this stuff. I did some research and found Primocon works good I was really impressed with it. The stuff dries hard and sticks like sh*t to a blanket. I put 7 coats on the the 24 foot aluminum boat. The mufflers used on the old detroits going to be too much back pressure for the cummins? Boats are a labour of love lol. My opinion is do a good job the first go around sure makes a difference. Clean fuel is a must, the bio blend diesel fuel today is horrible crap. In my experience it clogs up fuel filters quicker in years past. I would have Racor on the day tank one for each engine. Then I'd have spin on filters on the engine. The Cummins are a little more sensitive to fuel quality compared to the green grenades. N65 injectors are tough. The 6.7 Cummins I assume you have to watch fuel restriction with high micron filters. I'd even consider having your fuel tanks polished seeing your building a whole new fuel system. A good piece of mind you are not going to have a big algae slug plugging up an outlet on one of your tanks.
Thanks for the comment! The boat had a 13' extension added some time in the 80's. It took us a bit to get used to for sure but we love it now. Its all storage and tankage back there. There is another 500 gallons of water and 1000 gallons of fuel back there. The only time we get rumbling back there is when the props start to get a bit dirty. Its hard to say what effects it has but theoretically it should give us a bit more speed. We really like Osborne. They repaired our props last time we were here and Jody was extremely helpful with sorting out the propping requirements for the repower. Our shafts are only 2.25" as the wheel sizes and HP levels are fairly small on this boat. The couplers on the new transmissions are a bit shocking as they have TWELVE M16 bolts for attachment! If those ever break we have big issues. Going off of previous engine performance we will be turning 1600 RPM at our continuous cruise speed with the new engines. The peak efficiency for them is somewhere around 1800 RPM. We are definitely after economy. Will be interesting to see where we end up. That Interprotect is nasty smelling stuff for sure. I give Janis trouble all the time about wearing a mask. She did use the Primocon this time around on the rudders though so we will see how that works out. The mufflers should be more than adequate for the new engines. If they could flow enough air for 14L 2 strokes they should be able to handle the Cummins. They are pretty massive and have large internal openings. We try to do it right the first time for sure. The cummins are incredibly sensitive to fuel quality for sure. I went with the larger of the spin on options to keep restriction to a minimum. The setup I have run should be better than what would have come on the OEM versions of these engines. I had debated running one of the DAHL filters per engine but I wanted to filter the crap out BEFORE it even made it to the day tanks. All of the fuel coming from the keel tanks MUST go through the pair of DAHL filters before it gets to the day tank. This setup will also allow me to polish the fuel in any tank as well. Me move fuel through the day tanks fairly regularly and the tank suction fittings are off the bottom so there isnt much of a change to get buildup in there. That being said I am adding inspection ports into the day tanks this time around to make sure the new fuel system is starting with a clean slate. The Fleetguard spin on filters have a pretty large crud holding capacity and also have water in fuel sensors built in which I have wired to the engine management for alarms. The remainder of the tanks are skin tanks with big access ports so I will be pulling those for inspection and cleaning before we leave on our big trip. Thanks for watching and maybe we will see you around.
1200 - 1300 rpm is to low for those motors
The Detroits definitely don't like it. The Cummins 6.7 engines don't really care. As long as they have a good break in they are happy running anywhere as long as you keep them below the prop curve.
@@OnboardTangaroa great question and answer 👍🏻
Thanks!
What's with all the pin holes in the anchor locker?
I wish we could tell you. Our guess is that there was some sort of a name board (or multiple) screwed in there at some point. Its on my list to attack at some point. Thanks for watching.
The pretty gold stuff you prepped the boot stripe with is Hexevalant Chromium. You should not be rinsing it off in the boat yard. It's highly illegal..
We were told this yard had a filtration system and that it was acceptable. We will have to look into that. Thanks for the tip.
they probably switched filters when diesel went to ultra low sulfur im guessing
Possibly so. It may forever remain a mystery. Thanks for watching!
@@OnboardTangaroa might want to look into hydrophobic coatings for the hull bellow the water line for efficiency, the navy uses them in many applications
I will look into it. It will be a bit late for this yard visit but for the future......
so its a two shaft boat? two props? i thought i saw 4 at one point but...
It is a twin engine/prop boat. Four would be pretty wild.
@@timolson7005 They had 2 spare props that were a different size.
Sorry, I guess I should have caught that and clarified. Ecossearthur is correct. We have 2 spare props that are not quite the right specs but would work as spares in a pinch.
Don't put them back aboard when there is really asbestos around the mufflers. You will get sorry because there will be a time you have to discard them and then your whole engine room will be contaminated.
Only one was removed for access and it is already back aboard. Asbestos is fine as long as you can keep it encapsulated which is what we are doing. If they have to be removed at some point we will tackle that job at that point. Thanks for watching.
Why are you not wearing a mast all that sanding dust is bad please think of your Health
We try to all the time but sadly we do forget at times.
When you sand any kind of paint it’s important to wear a particulate filter mask. Your lungs aren’t made for nasty paint dust. You don’t want lung disease.
While we sometimes forget we make an effort to wear them every time. Whenever I see Janis sanding without one I give her trouble and vice-versa. It is important for sure. Thanks for watching!
These ones aren't good england!
I would like to answer but I don't understand?
What is Tangaroa ??? It’s pronounced Ta sounds like tar. the nga sounds ng-ah roa sounds roah roll the r sound…. So tarngahroah. Try not to pronounce tang eerowah 😂😂 Tangaroa is the Maori god of the sea😮🇳🇿🇳🇿
Thank you for the clarification. We will try to do better with that one. We did know that Tangaroa is the Maori god of the sea though. Janis and I became a couple while working aboard a yacht in your amazing part of the world. Funny enough, as tourists do, we purchased a wood effigy while we were there. We did not even know it was Tangaroa until after we had purchased and named our boat. Coincidence? Fate? Who knows? Thanks for watching!