how much do all thease parts cost to rebuild the pump when needed ihave mine on a john deer power washer the soap injector wouldnt work been sitting for a couple months in the cellar i took the injector off cleaned it but it still wouldnt work didnt have much time for it after that i had it back in the cellar and took it a part some more and cleaned it and sprayed some wd40 guess ill have to try it again next time i want to rince the salt off the my truck
I've followed this to the "T" and I've got "0" psi on the pressure gauge when pulling trigger on gun. Engine runs great, pistons move, all AR parts used to reseal the RSV Head with new check valves as well. Thoughts? I've also inspected the unloader valve to ensure there's no debris. I'm at a loss. HELP!
whats the difference between a pressure pump that has a high PSI rate but low water flow rate and visa versa? I dont understand.. There are pumps with a high PSI pressure rate yet the water flow rate is only 12L per minute and there are pumps that are low PSI but high water ie 18L per minute..... how do you know which is stronger? You would think that the higher the PSI pressure rate the greater the water flow rate but its not the case! I just dont get it.
I have a 4000 PSI. After I notice the Lost of pressure The gauge that I put on my pressure washer is only reading 2000 maybe 1000 psi. And when I pull on the trigger it goes too damn near 0. What would be that problem?
Lol. One criticism if I may..... you added the locktite to the valve right over the top of the slot it goes into... what if that dripped right down the center into the manifold? Great video ///. I learned something
What is under the ez start I open mine and the tap was on I think I lost some parts
thank you so much for this video
how much do all thease parts cost to rebuild the pump when needed ihave mine on a john deer power washer the soap injector wouldnt work been sitting for a couple months in the cellar i took the injector off cleaned it but it still wouldnt work didnt have much time for it after that i had it back in the cellar and took it a part some more and cleaned it and sprayed some wd40 guess ill have to try it again next time i want to rince the salt off the my truck
Whats the proplem when the motor trys 2 stall under load Luke therez to much pressure
Super
I've followed this to the "T" and I've got "0" psi on the pressure gauge when pulling trigger on gun. Engine runs great, pistons move, all AR parts used to reseal the RSV Head with new check valves as well. Thoughts? I've also inspected the unloader valve to ensure there's no debris. I'm at a loss. HELP!
whats the difference between a pressure pump that has a high PSI rate but low water flow rate and visa versa? I dont understand.. There are pumps with a high PSI pressure rate yet the water flow rate is only 12L per minute and there are pumps that are low PSI but high water ie 18L per minute..... how do you know which is stronger? You would think that the higher the PSI pressure rate the greater the water flow rate but its not the case! I just dont get it.
My pressure washer does not stop when I release the trigger. It is an electric mi-t-m. Could you give me an idea of what it could be? thank you
I have a 4000 PSI. After I notice the Lost of pressure The gauge that I put on my pressure washer is only reading 2000 maybe 1000 psi. And when I pull on the trigger it goes too damn near 0. What would be that problem?
It could be the EZ start plug spring maybe be broken (the nut just behind the unloader near the thermal release valve)
I have otroy prsmachine 2550psi were to get parts or the kits ass
Lol. One criticism if I may..... you added the locktite to the valve right over the top of the slot it goes into... what if that dripped right down the center into the manifold? Great video ///. I learned something
The bigger problem is he used red locktite, should use blue.
And also he's using a grease made for bearing on all the rubber seal, not the silicone grease.. not a good tips to follow..
Excellent. I was looking for the oil for the water pump and I think it is the 15w 40.
it is right?
SAE 30 non-detergent oil.
At 2.15 in video it says on info plate 15w40. Some pumps do use a non detergent 30w oil, it doesn't foam up , but this one says 15w40
You cannot find these reversible pliers anywhere.
where can i buy reversible pliers ?
It's good
“Red” Locktite????? Are you crazy??
You should have used blue.
Yeah, those check valves don't just come out that easy on a used pump.....
Could you please give us a link where to buy that reverse pliers i’ve looked diligently and have not been able to find those. Thank you
www.ppe-pressure-washer-parts.com/product/4.901-062.0
Here a link to our reverse pliers.
Please help!! If i wanted to run this to a bypass tank would i take off the bolt on the left of the unloader at 2:50 in your video?
or should i run a 3 way the put the outlet valve on etc
Where is tha global car wash services
1900w