Could you describe the relationship between the binary options regarding start, fuel, and so on in junction with choosing to use the relay board or not? Also, troubleshooting loss of DC voltage readings if possible. Where you have 12vdc going in to + and - but the screen reads 0vdc even when the relay board is bypassed. Thank you
The relay board is intended to be used when upgrading the previous MRS17 controller with the new MRS19 controller. The MRS17 controller had a two-wire dry contact for binary output 1 and 2 which was intended to be used for the purpose of starter and fuel solenoid. The MRS19 has only single-wire low-side outputs that close to the negative battery terminal when closed. The relay board adapter will provide you with the two-wire contact on outputs 1 and 2 in the MRS19 so the physical wiring coming from the controller will not be required to change. The remaining terminations are straight pass through to the controller. As far as the battery voltage reading...I would ask that you please save your controller archive when connected to the controller. This will allow us to review the file and determine what the misunderstanding or issue may be. The ComAp Technical Support team can be reached by e-mail at support@comapllc.com or phone at 1-844-267-1226. Thanks and Best Regards!
Hello!! How are you? Can you provide me with a manual to program the controller? I have an MRS10 module. Is it possible to program it without connecting it to the computer? that is, directly on the computer. Thanks!
HOla! Saludos yo acabo de hacer exactamente este mimo proceso para colocar correctamente el sensor de combustble y al grabar la informacion dio un error y ahora no prende la controladora y muestra en la pantalla CFG ERROR asi la apagues con el switch completamente, no hace nada se queda alli. Como se puede solucionar este error? Ya que tampoco accesde a internet ni se conecta nuevamente. Gracias
The troubleshooting gone into determining why you are experiencing RPMMeasFail can go a couple different directions depending on how you are attempting to measure RPM. For proper Technical Support, please contact us at support@comapllc.com and we will be more than happy to assist you. Thank you, ComAp Technical Support
I have replaced with new MRS 16 module, started the engine and immediately stoping by activated FLS fuel level alarm. We don't have fuel level sensor. How can solve this problem. Please advise.
Can i know why is the ECU alarm pops out but we didnt even know whats the issues? But the generator able to operate.
Thanks for this useful video....
how to wire an analog probe (4-20mA) three girls with the AMF? wiring diagrams
Could you describe the relationship between the binary options regarding start, fuel, and so on in junction with choosing to use the relay board or not?
Also, troubleshooting loss of DC voltage readings if possible. Where you have 12vdc going in to + and - but the screen reads 0vdc even when the relay board is bypassed. Thank you
The relay board is intended to be used when upgrading the previous MRS17 controller with the new MRS19
controller.
The MRS17 controller had a two-wire dry contact for binary output 1 and 2 which was intended to be used for the purpose of starter and fuel solenoid.
The MRS19 has only single-wire low-side outputs that close to the negative battery terminal when closed.
The relay board adapter will provide you with the two-wire contact on outputs 1 and 2 in the MRS19 so the physical wiring coming from the controller will not be required to change. The remaining terminations are straight pass through to the controller.
As far as the battery voltage reading...I would ask that you please save your controller archive when connected to the controller. This will allow us to review the file and determine what the misunderstanding or issue may be.
The ComAp Technical Support team can be reached by e-mail at support@comapllc.com or phone at 1-844-267-1226.
Thanks and Best Regards!
Хорошо!
Please let me know how to activate avr and governor drive
Hello!! How are you? Can you provide me with a manual to program the controller? I have an MRS10 module. Is it possible to program it without connecting it to the computer? that is, directly on the computer. Thanks!
HOla! Saludos yo acabo de hacer exactamente este mimo proceso para colocar correctamente el sensor de combustble y al grabar la informacion dio un error y ahora no prende la controladora y muestra en la pantalla CFG ERROR asi la apagues con el switch completamente, no hace nada se queda alli. Como se puede solucionar este error? Ya que tampoco accesde a internet ni se conecta nuevamente. Gracias
tienes que cargar el firmware por default de tu control, y hacer el reboot loader
Y de donde saco mi firmware nuevamente? Es un IL-NT-Pramac AMF26. No funciona completamente con el software amf25 que traen los comap por defecto
hello , i have problem with my pramac machine, the controller is not showing value, nothing on the screen, please help me.
reboot loader firmware
How can I download software?
how is i am downlod
Dear,
How can i install the software suite.
Please send me the link of download.
Thanks Advanced
Hello how can I download software?
Dear,
How can i download this software, please provide me download links.
Thanks Advanced
Hello sir. Our generator controller will not detect the RPM. So it will automatically stop due to alarm RPMMeasFail
The troubleshooting gone into determining why you are experiencing RPMMeasFail can go a couple different directions depending on how you are attempting to measure RPM.
For proper Technical Support, please contact us at support@comapllc.com and we will be more than happy to assist you.
Thank you,
ComAp Technical Support
I have replaced with new MRS 16 module, started the engine and immediately stoping by activated FLS fuel level alarm. We don't have fuel level sensor. How can solve this problem. Please advise.
We have ic-nt mint controller i cant connect to lite edit software please help me why i cant connect