How to install the 5 color spray jets. I use a red jet on my pressure washer for roofline hornets. I want to add a liquid bug/hornet in the container. I don't see how I could install the individual jets with the splitter at the end of black housing. Or are these 5 multicolor jets used in another application.
Hi Jacob, one of the critical points to create thick is pressure. I'm still confused, the pressure is actually measured on the head of the machine or on the hose? Because if some jet steam they put the pressure gauge on the head of the machine and they claim that the pressure stated on the box is equal within the pressure gauge (which is located on the head of the machine). But when we put another pressure gauge between the hose and before gun spray so we will find the pressure is far different. Could you help me with this?
If you are under 2gpm you need a new orface for thicker foam to a smaller one. If you’re over 2 gpm you don’t need to change Jack shit and know how to dilute.
Seriously, waste of time! Don’t pull it apart! Soak entire brass fitting in hot water. For a bit. Dump half a bottle of shower cleaner in a bucket. Throw in brass fitting. Top up with boiling water. Soak. Fixed!! Always flush foam cannon with clean water after use. You won’t need to service it
Yep this is how I was told to use a foam cannon. You rinse the bottle out afterwards, refill with just water and spray it empty whilst twisting the adjuster every which way.
I was ready to give this product a bad review. But I appreciate that you made this video! and how you made it easy to follow instructions! Great job!💯🫡👍
Was literally about to trash my foam cannon . This saved me some money. Thanks!
I’ve thrown number of foamers
Thanks for your video, the only one that shows how to dismantle the entire foam cannon
oskkkuu, ik, uü"9six9x(777798⅞(„('u u uuúkxtjg"jxkxk
Thanks mate, you just saved me from buying another one.
Throttle body cleaner works great too.
That helps a lot cheers mate ❤
Fantastic video. This helped me out a lot. 👍🏼
Best way to de-wax it is soaking it in mineral spirit.
Mineral spirit?
Just boil it in water for a few minutes
@@miketampabay9446 thanks mate!
Mine pulsates. I did this but didn't fix the problem. Any ideas? Thanks
How to install the 5 color spray jets. I use a red jet on my pressure washer for roofline hornets. I want to add a liquid bug/hornet in the container. I don't see how I could install the individual jets with the splitter at the end of black housing. Or are these 5 multicolor jets used in another application.
Great video thank you
My gauze piece is rock hard, is that normal. Don’t have a new piece to compare it to
Yes that's normal
Just did all this and STILL doesnt work
Hi Jacob, one of the critical points to create thick is pressure.
I'm still confused, the pressure is actually measured on the head of the machine or on the hose?
Because if some jet steam they put the pressure gauge on the head of the machine and they claim that the pressure stated on the box is equal within the pressure gauge (which is located on the head of the machine). But when we put another pressure gauge between the hose and before gun spray so we will find the pressure is far different. Could you help me with this?
No it’s how much GPM you have not pressure…
If you are under 2gpm you need a new orface for thicker foam to a smaller one. If you’re over 2 gpm you don’t need to change Jack shit and know how to dilute.
Changed filter on all 3 and fully cleaned but will still not spray foam? Any idea why please
check the inlet pipe for blockage
blow it all out with a air gun
Wher do u get the o rings from
Harbor Freight has a O-ring kit with a shit ton of them for like $10
A wire hanger works good for pushing out the pin, a 5/8 socket with an impact worked well on stubborn fitting... Was too tight for me.
I just got mine on ebay and it worked for a few sec then stopped, you have no idea the stress you lifted
I won't go Tru all that work. A new bottle isn't that expensive
It is expensive in my country
Seriously, waste of time! Don’t pull it apart! Soak entire brass fitting in hot water. For a bit. Dump half a bottle of shower cleaner in a bucket. Throw in brass fitting. Top up with boiling water. Soak.
Fixed!!
Always flush foam cannon with clean water after use. You won’t need to service it
How long do you let it sit in the hot water
Yep this is how I was told to use a foam cannon. You rinse the bottle out afterwards, refill with just water and spray it empty whilst twisting the adjuster every which way.
Anyone know why mine shoots loses pressure gains pressure and repeats
It’s an electric pressure washer with 1600 psi
Same as mine
Thanks
I was ready to give this product a bad review. But I appreciate that you made this video! and how you made it easy to follow instructions! Great job!💯🫡👍
Thanks