Always found it much easier to go from the top down into the tank & pull thru with a pair of long pliars! No need for the xtra wire. Always worked well for me!
On the primer bulb , the IN side goes to the small brass tube on carburetor and the OUT side of primer bulb goes to tank return by the right side of carburetor as viewed from the top of saw ! The idea is the primer bulb when pushed in squirts gas into tank and when released pulls gas through the fuel filter via drawing it through the carb through the small brass tube on carburetor
I hope you don’t have to work on that Troybilt 4 cycle trimmer on the table. How do I know this? Because I replaced the starter pawls on mine twice because it never started right from new, Then when it started bogging I threw it across the yard, I bought an Echo trimmer 3 years ago and never have had any problems.
I just got one of these for free as well. A Poulan 220 Pro 38cc. Completely trashed, rusted bar and chain, no fuel lines or primer bubble. Looks like it was sitting under 3" of mud for a while.
wanna come over and fix mine? hahaha i cleaned the filter on carb-blew it off, looked at spark plug but couldn't get it out. bulb pushing fuel. IDK. has ruined my fire to go cut wood.
I've tried for years to develop any affection at all for poulan saws, just because everyone dogs them. I just can't do it. They all suck. Poulan made me ditch anything from husqvarna and start buying stihl and echo products.
Always found it much easier to go from the top down into the tank & pull thru with a pair of long pliars! No need for the xtra wire. Always worked well for me!
good clear from the first to the end good about a little wire tool to feed the fuel line from fuel tank to the carburetor thank you !!!!
Glad it helped👍👍
Good job. I pull the lines from the carb compartment to the fuel tank using a pair of locking forceps or hemostats.
Thanks for another great video 📹!!
Great video and instruction! Thank you!
👍👍
Keep on 'Pullan' '
On the primer bulb , the IN side goes to the small brass tube on carburetor and the OUT side of primer bulb goes to tank return by the right side of carburetor as viewed from the top of saw ! The idea is the primer bulb when pushed in squirts gas into tank and when released pulls gas through the fuel filter via drawing it through the carb through the small brass tube on carburetor
Great stuff! Was curious if that fuel line would feed better if left in the freezer for 20 minutes or so?
Cut a small taper on the end of the new fuel lines & they will go right into the tank!
I think it's going to be just like that one but I know how too adjust it now thanks a lot very much
Glad I could help
Do you have rattle snakes sounds like it,?
Thats a Nice trick. But how did You tie the wire?
fuel lines are the weak spot on them ..i have that saw,,an many other poulans very easy to work on,,,
Every year
small fuel line is supposed to go to fuel filter
Great video
Dang, sounds like a jungle out there.
I hope you don’t have to work on that Troybilt 4 cycle trimmer on the table. How do I know this? Because I replaced the starter pawls on mine twice because it never started right from new, Then when it started bogging I threw it across the yard, I bought an Echo trimmer 3 years ago and never have had any problems.
Y
Well yeah Troy Bilt is junk.
Fuel line
How to Install fuel line
Fuel lines filter and metering diaphragm and fixed
Best to order a air boot to
There short life
Very popular in west Texas
good job
I think it's the Leatherface chainsaw replica.
Is the sprinkler on or a heard of snakes? 😁 (👍)
LOL 👍👍
Where can I order that same gas line? good vid man!
I believe I got it on Amazon.
@@SmallEngineDIY thanks man
The chain should not be moving at idle if the chain brake is off and the throttle isn't depressed. You may have a bad clutch brake too!
That particular model saw has NO brake.
I just got one of these for free. I figure the initial investment being free it might me worth playing with to get running
Good luck with it!
@@SmallEngineDIY Got it running! Thanks for your help. You gave me the confidence to giv’er!
I just got one of these for free as well. A Poulan 220 Pro 38cc. Completely trashed, rusted bar and chain, no fuel lines or primer bubble. Looks like it was sitting under 3" of mud for a while.
wanna come over and fix mine? hahaha i cleaned the filter on carb-blew it off, looked at spark plug but couldn't get it out. bulb pushing fuel. IDK. has ruined my fire to go cut wood.
It can be frustrating, but don't give up!
it needs to lay on the bottom
I expected an ostrich to stick its head into camera view...you must live on a wildlife preserve....not that that is a bad thing...
I cant get past the background noise, sounds like a rattle snake nearby. Get that chainsaw fixed quick or else!❤
Its poulan not poolan 😅
I've tried for years to develop any affection at all for poulan saws, just because everyone dogs them. I just can't do it. They all suck. Poulan made me ditch anything from husqvarna and start buying stihl and echo products.
Pisto ring