Making Hydraulic & Hydrostatic Dump Truck
ฝัง
- เผยแพร่เมื่อ 17 เม.ย. 2024
- In this video we will show you how to make an interesting vehicle that will be very helpful on the farm and around the house.
You might say it was easier to use a lawn tractor and convert it, maybe it was, but we didn't have one and we had a lot of parts we wanted to use.
Parts we used:
- Hydrostatic transmission from a lawn tractor
- The main frame is made of a 70x50x3 mm channel
- The steering gear was found in a scrapyard, unfortunately I don't know what car it came from.
- Briggs & Stratton petrol engine 14 HP
- The seat is from some lawn tractor
- The footrests, sides and crate are made of 1.5 mm stainless steel
- Fuel tank from the gx200 engine
- The air conditioning compressor is probably from a Ford
- Hydraulic pump with a capacity of 10L / min
- Hydraulic cylinder with a height of 200 mm
Specifications are:
Weight approx. 250 kg
Load capacity on the trailer: approx. 400 kg
Power 14 km
Maximum speed 15 km/h
The dimensions of the box are 90 x 96 x 40 cm
Check out our other videos:
• Making revers trike to... - Making reverse trike to Have Fun :D
• Making Hybrid Stump Gr... - Making Hybrid Stump Grinder
• Making 14 Hp Brush Mow... - Making 14 Hp Brush Mower - using Lawn Mower parts - ยานยนต์และพาหนะ
You're a great fabricator...always a pleasure to watch!
Thanks! 👍
You should start production… AMAZING INGENUITY…!!!!!!!😮❤😮
@@MadeinPolandChannelqqq
Nice build
A nice build and a useful machine.
10/10 on the reparability though. There's not a SINGLE inaccessible void, other than the obvious hydraulic oil tank.
True Professional and I couldn't stop watching this magician from start to finish and I hope he is self employed because he is too good to waste on someone else
Молодец. Хорошая машина получилась.
These hydrostatic transmission need larger oil capacity a external filter.
For heavy work.
Many failed here in mountain lawn mowers.
Axels can't carry much weight also.
Excellent channel 👍
My grandparents from Poland Lithuania.
I agree even on relatively flat land any transaxle smaller than a Tuff torque k66 just won't last on slopes... Also most transaxles under 1inch axle shaft cannot hold much weight... Best bet is to use transaxle as a transmission with a separate load bearing axle with hubs chain driven from transaxle shafts with a 1.5:1 or 2:1 chain ratio driving the rear wheels
It doesn't help that the box stores spec 30w motor oil in the TTs (my homedepot cub's manual states 30w). TT specs 50w in their service manuals. Built in failures. Only buy the mowers from the dealers. They are made in the same factory but built to different specs for the different distributors. You want a JD, go to JD for it, not the box stores.
It's always a pleasure watching a master fabricator build stuff.
Dude you are amazing
Protect this man at all costs, we need him in the coming apocalypse.
Wouldn't it be wiser to seek/know how to avoid being here for what you've rightly said IS coming [tribulation/apocalypse]? Sadly, most reject the truth/answer when they hear it because it's inconvenient to their lifestyle. If people only knew how bad it's going to be [globally] for those who reject the answer: To be right with God; Jesus-by grace thru faith *apart from* human effort: good works, rites, ceremony [Eph 2v8-9; Gal 2v16/3v10/5v4; Rom 3v20]. *"Truth is a stubborn thing"*
"For then *there will be a great tribulation,* such as has not occurred since the beginning of the world until now, nor ever will" [Matt 24 v21]
"for those who reject the answer" Didn't God say that this would be how it is in the end?😫
Молодец мужик рукастый !
EXCELLENT idea with the AC compressor clutch. Keep it on the same belt, flip a switch and you have PTO. Love it.
The thing I like the most about your channel is the advanced thinking you constantly put forward. While the rest of the planet is busy destroying itself, you are busy engineering and making positive contributions. I hope you last forever!
It turned out to be a good dump truck!👍🙂 It can be slightly improved for transporting light but bulky cargo (firewood, hay), and an addition to the sides made of mesh with reinforcements. The additional weight will be small.
Another mechanical masterpiece .
Great build... you could go bigger in size and make an industrial version of this... SO cool !
Хорошая работа!
Magnifique travail bravo, et c'est une crémaillère de r5
Love all your projects, especially your vehicles!! I learned a lot from watching your projects. This one is amazing, thanks for sharing with us!!! How about showing us how to make a 4WD vehicle 😎🙏
Time well spent. There can't be much to go wrong with this either and anything that does can be fixed easily enough.
Yet another masterpiece of engineering. You always make something that is not clear from the beginning, but as the build grows, everything comes together as one perfect example of what can be done with a little forethought and some considerable skill. Thanks for teaching us what can be done, Much appreciated video, helps add to inspire ideas for the future. From UK.
Love the longer formats. If i want to skip a section... Tap tap + 10 seconds. Buuut. If I want to watch the whole thing now i can!
Amazing talent he have and shareing his idea to everyone how we can make it such . Impossible thing to possible. 🥰🥰🥰
This might be my favorite build of yours yet! Such a practical and useful creation. Always a big treat when you post a new video!
μπράβο σου φίλε πολύ ωραία κατασκευή χρειάζεται σε κάθε είδους δουλειά σου εύχομαι ότι καλύτερο ευχαριστώ για το βιντεάκι 😊😊😊😊
Great work my master you are awesome engineer thanks for the sharing this video sir 👍 😊❤😊❤❤
Taczka zmotoryzowana
O Stary, jesteś genialny! Z chęcią bym u Ciebie pobierał nauki i pracował. Bardzo zazdroszczę (w pozytywnym tego słowa znaczeniu) wiedzy, umiejętności i precyzji wykonywanych rzeczy.
Mega szacun!
Howdie from Canada 🇨🇦 Sk thinking about how you built this awesome workmanship for what ya do and build thank you for sharing with us this is worth watching ya got this something that can be used and easy to make don't have to be a rocket scientist to be able to do this later mighty fine 😊
Idealny sprzęcik w gospodarstwie, piękna maszyna. Pozdrowionka
AWESOME build.....great vid of an fabricator you are...MOPAR 4 EVER.
Great work from a busy man. Thanks.
*GREAT JOB! GOOD LUCK TO ALL* 😎
Nice machine. I' want to build something like this but instead driving in opposite. So sitting on engine and have the load in front. This to reduce the space taken for having a seat.
Patrz jaki pomysłowy Dobromir!
Sweet, great execusion. I've been thinking of building something similar for a while just not made it to the top of the list.
Kind of cool but that's why you pull a dump wagon behind your riding lawn mower
I was trying to come up with a reason why this would be better than just making it a small dump trailer and all I could think of is "tell me you can't back up a trailer...without tell me " 😂
Impressive fab work regardless
The issue with a trailer is it's added weight to the tractor plus 2-4 more expensive tires to purchase and not very menueverable and I doubt a lawn trailer could carry as much as something like this.
If you were a small landscaper, that does custom walkways and ornate flower walls, i could envision this hauling sand to the tight areas plus a modular body system where as you could detach the dump bed and mount a small mixer or do a slide in mixer to make small mortar batches. This is ingenious.
Coraz bardziej złożone te twoje projekty😊Z takim progresem to juz niedlugo łodzie podwodne i promy kosmiczne zaczniesz budowac😅Jak zawsze 3mam kciuki🤞i pozdrawiam z drugiego końca naszego kraju😉
Tak na marginesie czy w 12 minucie i 40 sekundzie tak mniej więcej czy proces spawania nie jest czasem puszczony odwrotnie? Czy tylko ja się zawiesiłem 😂 Zawsze staram się przyglądać wszystkiemu dokładnie alu tu wydaje mi się że film ,,leci do tyłu"🙃ale to pewnie ja jestem zakrecony 🚀
Z takich narzedzi co nie masz a można by pomyśleć to czas powoli zbudować giętarkę do rur💪to by było dopiero coś🤩rurowe konstrukcje, klatki, ramoklatki, lekkie i wytrzymałe a nie zawsze spawane z ciężkich profili ciętych pod kątem 🔥
@@marekroszkiewicz3524 A no trochę trzeba rozwijać kanał i iść i odmienne konstrukcje 😁😁 Mam taką giętarkę, hydrauliczną, ale jakoś rzadko jest w użyciu, jakoś ta bardziej wole profile niż rury 😅😅
Silnik z połowy Malucha ;)
Też tak umiesz, ty połowa mózgu ?
Paul from Fabs Rat hasn't got anything on this fabricator. Nice Work 👍
Impressive! Very impressive! Such skill in fabrication.
I enjoy watching and guessing what you may do makes it fun. Excellent work
Если хочешь чтобы при сварке было видно дугу на камеру. Сделай очень яркий свет. Чтобы камера не меняла яркость.
you mate are one talented guy, Top Class
Retrofitting an old AC clutch to your hydraulic pump was really done!
i love your projects because all of them are heavy-duty and really strong
Thank you 👍
Awesome job and a good job on the paint too I like the color cool dump truck so I take it you're a machinist by trade because you look like you know what you're doing awesome video hope to see more of your builds
Just goes to show. A work shop, a little saw cutting, welding & plasma cutting. Anything is possible. Oh, and a LOT of time and 💸 , too❗️🙄
Hello everyone have a nice day this is the amazing video
Love the build 👍, this looks like the projects on those small tractor forums where owners will add a backhoe or front end loader to their garden tractors.
Looks and runs great. I would add a few link of chain to the side panels of bed and a hook in the bottom corners of end gate so you can hook the chains to keep the dump gate from fully opening this would allow you to dump a consistent amout of gravel dirt or wood chips for spreading it as you dumped
i'm here since you only had an angle grinder and a stick welder, impressive how far you have come.
thanks for being our viewer for so many years!
As always....well made clever design,👍
Железный человек, у него наверно повышнный гемоглобин, так железо чувствовать, за что бы он не брался всё получается на высшем уровне. Всего хорошего хорошего вам.
@ 22:32 ... Who needs drawings & plans 2 work 2;... when they R stored in your Brilliant Mind...
Very nice build and video, thanks.
Pracowite i zdolne to chłopczysko z Podkarpacia , a propos najbardziej podoba mi się ta piła do cięcia , chyba sobie taką kupię do krajania mojej swojskiej suszonej kiełbasy 👍👍👍👍👍👍👍👍
That's the coolest thing ever! Makes me sad though because I just threw away a Cub Cadet hydrostatic drive...but I did use the engine and controls in a wood splitter build. About that firewood- get yourself some IBC totes 🙂
Натяжение ремня гидравлики правильно сделал а ходового ремня неправильно
Very nice. I probably would have put a longer exhaust on it as well.
Годный трактор получился. Жалко, что ремень привода и подшипники снизу ни чем не защищены от грязи и веток. Надолго их не хватит.
Quel travail. Bravo c’est vraiment super. Merci pour cette vidéo.
Już wiem jak zrobić wspomaganie w traktorku dzięki wielkie 🤠
Bonjour belle réalisation avec de l’a récupérations de pièces automobiles et très bien équipé dans l’atelier 👍
Za cały dzień oglądania twojej pracy na żywo, mógłbym na fajrant sprzątać warsztat 😂😅
Jak zwykle kawał dobrej roboty 💪
Podziękował 👍😁
hi forma cool hydroaulice truck two
cool ass truck two🎉
Хорошо получилось! Ты настоящий мастер!
So you took a lawnmower and a dump cart and combined them🎉🎉😂
You should add blades on the bottom to cut grass 😂
jak zwykle, rozdupcony system. Brawo!
Thanks, just great! 👍💪✌
Io posso solo dirti che ogni video che fai è un capolavoro di ingegneria. Quanto vorrei poterti stringere la mano e dirti che sei un ragazzo davvero geniale. Grande DARUZ
That's a excellent built. Something I could definitely use.
I enjoy watching your videos. You all ways come up with new ideas 👍all the way from California 🇦🇲
I love that work excellent excellent work thanks for sharing your video look forward to the next one and I love your welding
Браво Маэстро !!!
Super super, wygląda naprawdę ciekawie, dużo pracy
Wow! That little thing comes in handy. Are you building yourself an adult version of the metal Tonka trucks from the 70s? Thank you for taking time to build, film, edit and post this video.
That's awesome! I actually have a neighbor that tried to build one! After 3 years and who knows how much money it's rusting in his beck yard!
It is a pity. He could have a very nice vehicle.
That guy can build EVERYTHING
Cool video, wondered what it took to repurpose a hydrostatic drive.
Lots of guys can fabricate stuff, but not many can do outstanding editing as well. Great combination.👍👍
Editing the videos is thanks to my brother, he does it 😁
Great work. Tho a trailer would have been super easy to male to just pull behing the mower that was gutted to make it. But where is the fun it that.
Cool new addition to the work toys. Thankyou for sharing with us. 😀
Well done great idea.
Another great build love your videos
سلام خسته نباشید عالیی مرسی که هستین ❤❤❤❤❤❤❤❤❤❤❤❤
Excellent work again !! very usefull and cool project! salutation from Montreal,Québec !👍👍👍👍
Nice work,👍🏻
Nice smal dump truck . Great job . 👍👍👏
Cool build! I know it takes lots of time, keep up the good work!
I always look forward to the adventures in your videos. Very nice work, and especially using stuff that is salveged.
good builder very talented keep going we love this stuff
Sehr schön geworden, wirklich ein prima Erfolg!
... Und es sieht bei Euch im Dorf und drumherum genauso aus wie in unserem Dorf in der Eifel!
Very impressive!
That cutting to fit the bracket,
So much for nice powder coat
I really enjoyed this. Excellent fab skills.
Master of Fabrication
Fajny sprzęt👍 Przydałby się jeszcze jakiś hamulec postojowy😉
C'est la première fois que je vois une courroie aussi longue! Le risque de perte de motricité est réel 🤔