Connecting plaster station G4 | Operation

* Where is the plaster station connected?
The PFT G4 station is connected to electricity and water.
• How to connect to the power supply?
The G4 is connected to a three-phase power supply with a 25 amp protection circuit using a 5x4 KG cable with a 32 amp plug and socket
It is convenient to connect the socket (Pear) to the panel, and already to this socket to connect the cable.
* Connection of the plaster station to the power supply must be carried out by a qualified electrician.
• And it is possible to work without zero?
For plastering machine must be 3 phase neutral and earth, it is possible to work without the zero, but then will not run auxiliary power outlet.
• How much does the G4 Smart plaster station consume?
Station G4 consumes about 7.5 kW.:
main motor 5.5 kW,
the motor of the drum 370 watt,
900 watt compressor
and if there is a built-in pump, then another 600 watts
• What kind of protective machine should be in the connection Board?
Should be installed machine 25 amps, as the machine 16 amps, will knock at the start of the station.
• How do you know that everything is correctly connected, including the direction of the phases?
After connecting the cable it is necessary to check the direction of the phases, if anything, perform the main switch re-phase.
The light should be blinking, then everything is fine.
If the yellow lamp is lit, it is necessary to switch to the other side and try again,
If the lamp is lit in both positions, there is either no single phase,
any imbalance in phases, but it happens very rarely.
If the lamp is lit in both directions need to call the PFT-master technician
• What is the diameter of the water hose to connect to the water?
The plaster station is connected to the water supply by a hose with an internal diameter of at least ¾ inch equipped with Geka connections.
It is also important that there are no kinks in the hose, so it is better not to use soft hoses.
• What water pressure should come to the plaster station?
The water pressure at the working station must be at least 2.5 bar, i.e. when the station is switched off the pressure gauge must be more than 2.5 bar
• What happens if the incoming pressure is less than 2.5 bar?
In the case of the boundary state, when the machine is turned off, the pressure is more than 2.5 bar, and when the pressure drops below 2.2 bar, the plaster machine is turned on and off (as fulfills the manometric relay), visually the machine begins to knock
So you can not work, as there is much stress on the gearbox.
• If the system pressure is not enough, what to do?
If the pressure is not enough, you can supply an additional pump.
Also, the number of incoming water may not be enough. In urban water supply is often: there is water-but not enough
On plaster machine consumes 650 liters per hour., the water supply system, for example, passes less
If the Central water supply doesn't give such volume, it is necessary to put a barrel and already from there to take away water.
* Is there a plaster station with a built-in pump?
There are two versions of PFT G 4 smart with built-in water pump and without.
The built-in pump serves to increase the pressure.
But you can use external that in some circumstances and with built-in pump.
The built-in pump only increases the water pressure, and the water to the pump must flow independently, i.e. the minimum pressure must be.
For example, if you take water from the tank, the tank should be located above the water inlet level in the station, so that the water flows by gravity to the built-in pump or you need an additional pump that will create pressure.
• What to do with air traffic jams?
It is necessary to ensure the pressure of the incoming water and let the air plugs.
• If the water is dirty?
Use need to clean water, you can put an additional filter.
• What's in the plaster of the car to do their water filters?
Filters two: one at the inlet, the other under the water reducer (show in the roller cleaning)
Do not touch the water reducer, it is initially set up and does not require intervention.
• How often to clean the built-in water filters?
Installed water filters should be clean and solid, you need to check daily.
(Show in the video cleaning)
The machine is ready to use, see the following video " setting up and running»

[@leoleonidus4321]

Хороший канал

[@user-xc6vr5gp6h]

На конец то сделали шторы для компрессора и насоса