JCB 3CX BEARING TRUNNION 2

jcb 3cx bearing trunnion,jcb 3cx bearing,jcb 3cx trunnion,jcb 3cx,spider cap,jcb 3cx,bearing taper roller,joint knuckle swivel ram,jcb 3cx csapágy,jcb 3cx féltengő,jcb 3cx kardán ,kerékagy, kardánkereszt,seal,

[@deniscolautti8358]

I miei complimenti per il lavoro di riparazione del fusello che hai eseguito alla terna , 💪👍👍👍Bravo

[@disturbedcarrot]

Lovely machine!

[@user-tv6zj2oe2w]

Ай, молодца!👍👏

[@dulurtkitv3693]

Jcb 3cx Top 👍

[@elviejoperro3077]

Excelente Job, painted and all, 👍

[@JaouadOumenni]

Good job 👍👍

[@user-pw3yv3fe4i]

Úgy tűnik, tiszta vagy és rendezett. Soha nem veszítesz, ha szervezett vagy. Nagyon jó munka haver.

[@miloudmecanique]

Bravo top

[@vlog1548]

✌️👍

[@jondoherty3678]

You need to heat bearing up to fit

[@vadimjcb3cxmurmansk]

Номера подшипника какие?

[@karolytoth4875]

Jó napot Laci először is Boldog újévet kívávok. Nagyon precíz fasza videó. Szeretnék tőled valamit kérdezni, hogy mi lehet a gond JB 4cx a hátsó gém rögzitésnél a kapcsolóval a rögzitőkről a nyomást akkor azt könnyen át lehetne tolni a gémet egyik oldalról a másikra.Előre is köszönöm

[@petessite]

always give the ol UJs a clout with hammer to make come lose a bit ,therell always be a bit stif when 1st put together , fill the cups with grease to stop the needles falling out , if one doesnt have a press ,the vice does the same job , good video of doing the trunions , well done , ol chap

[@jimmydickson8854]

How many hours did the old bearings and seals do

[@lacibatoch1673]

I don't know. That's how I bought it.

[@mordekai4182]

@@lacibatoch1673 thats a lot of work to do and change it. How much money were the parts only?

[@CASE-id4jq]

🤝🤝🤝🤝👍👍👍👍👍👍💪💪💪💪🔥🔥🔥🔥

[@rajivchumie]

Link to bearing race tool?

[@Narayan-Jadhav]

Hello bro I am jcb service engineer from India

[@In2investing]

Probably should've packed those bearings with grease before installing

[@quotesfor_u_99]

Yes

[@mqaconstructionequipment6683]

Let me know if you want a Job here in Australia

[@scottgm321]

It looks too new to go bad already. Previous owner must have never used a grease gun on it. There was still paint on the zert.

[@disturbedcarrot]

I think it was painted

[@richardschneider4775]

To do this job you really have to keep your bearing.

[@wotnoturbo]

Hungarian - right ?

[@disturbedcarrot]

Well done for recognizing that, my wife is Hungarian (Pécs) and I'm around the language all the time but still found it hard to identify it.

[@danjoe091]

Wrong grease nipples in driveshaft crosses,they should be on the corners .Driveshaft cannot be greased.Good video otherwise.

[@gulabkhan4662]

Good morning

[@vishnudutt664]

only from hindi ok

[@cassiatres5337]

Use

[@ruseshnagabangsh5933]

jcb 3dx mujecahe 400000

[@adriancristea8460]

Sei masterchef.mecanic