I am retired qualified electrician in Britain. Your video provides by far the best information on how to connect an overload. Manufacturers information adequately describes DOL and overload but fails to explain how to connect the two at all. Thank you so much !
Sir, I want to know that the voltage , mentioned here is 240 phase to neutral or 240 phase to phase voltage which is practised in the USA. Because I am from India which is following British standard...
I like the video but am I missing something here? The start stop circuits between the real and the schematic don't match. They may but they are drawn differently.
This is my project at my school. i wonder if i can do this without an overload relay? just the contactor only? and if yes, should i also connect the T3 of the Contactor to the L3 of the Contactor? thank you.
If you want to use contactor only, then you don't need a jumper wire. Simply connect L1, L2 and start /stop buttons as shown in picture. It will act as motor starter without any protection
MY lath stops & start opareats momaly but sometimes when my Nabour switched on jet washer my lath switches of { why} , Often i only use my lath for short runs of work , but in hot weather i find my lath will not run long [WHY] often My lath will keep turning of. But then after several tries it will say on & work normally for some time & restart Normally when next i return to ti {WHY} Las Thompson ? It is a Single Phase Stand aloe stop-start box
![ทุกครั้งที่หลับตา (Lucid Dream) - AYLA's [ Official MV ]](http://i.ytimg.com/vi/4i1OBAQyv58/mqdefault.jpg)
Thanks for posting this Bob. I ran into this issue this morning and your video helped to clarify why all three OL's need to connected.
Thanks a million Bob. This saved my A$$. Best TH-cam "How to" Video I've ever seen. You the man, keep up the good work!!!
I am retired qualified electrician in Britain. Your video provides by far the best information on how to connect an overload. Manufacturers information adequately describes DOL and overload but fails to explain how to connect the two at all. Thank you so much !
Mandy Haines Thanks for the kind words but we are just trying to share good information.
Hello and thank you .
Could you please tell me which terminals the 240 volt feed wires go in . it's hard to see on the video . I am in UK
There is A1 and A2
Sir, I want to know that the voltage , mentioned here is 240 phase to neutral or 240 phase to phase voltage which is practised in the USA. Because I am from India which is following British standard...
Its Phase to Neutral
Saleh thanks a lot
ramu ganesan please sand your no
Awesome very easily understood, how and why it needs to be wired in this fashion.
I like the video but am I missing something here? The start stop circuits between the real and the schematic don't match. They may but they are drawn differently.
Thank you so much, so simple yet so hard 😂.
This is my project at my school. i wonder if i can do this without an overload relay? just the contactor only? and if yes, should i also connect the T3 of the Contactor to the L3 of the Contactor? thank you.
If you want to use contactor only, then you don't need a jumper wire. Simply connect L1, L2 and start /stop buttons as shown in picture.
It will act as motor starter without any protection
hai, for power cct, is it black color of wire is for neutral and red color for hot wire
Easy to understand video. 🙏
I need help to connect a 3 phase contractor and overload to a single phase motor.
MY lath stops & start opareats momaly but sometimes when my Nabour switched on jet washer my lath switches of { why} , Often i only use my lath for short runs of work , but in hot weather i find my lath will not run long [WHY]
often My lath will keep turning of. But then after several tries it will say on & work normally for some time & restart Normally when next i return to ti {WHY} Las Thompson ? It is a Single Phase Stand aloe stop-start box
Enjoyable and understandable
Thank you!
Nice Video
Bob tq
hello please send me a control circuit of single phase line and factory starter connection diagram of 1000watts lamb
Still not getting any power
Where is capacitor connection
That symbol is a contactor in this context. .. i think this is what you are asking about..
Your pencil work is hard on the eyes, have not finished viewing. :-(
Whos talking Donald Trump?