I've watched probably every single video of Sal building a mud pan, it never gets old watching the best in the business effortlessly build another perfect project. Thank you Sal for continuing to share your expert knowledge with us.
The hole on the subfloor is much bigger than flofx flange drain outlet, so there is a gap between the outlet and the edge of the hole. Do you fill the gap up? Or will the gap cause mud bed movement in future?
Sal, im a DIYer. I see that you use multiple different systems, kerdi, latticrete. What would you recommend as the easiest system? I’m planning on doing a mud base slope to my drain and waterproofing and then tiling.
Good video! I always tape off my bottom piece with duct tape and cut it really nice to keep all the mud away from the drain. should that be done with bonding flamges to keep the mud off of the actual felt until you're ready to connect the actual membrane to it? And if so, which tape would you use?
3 bathrooms I’ve been to so far (this month) have had their drains situated flush with the wooden subfloor.. Any tips for what to do in prefloat situations - can you still prefloat or does the drain have to be redone?
I am guessing those were two stage drains, not a bonding flange type like the ones I use. They should have a preslope, liner and then final mud bed. Bonding flange has a single mud bed.
Do you have anything against slurry coating the floor before the mud instead of tar paper/wire when you’re waterproofing it anyways? Or is just a personal preference?
Sal I see screws in your cement board lower than three inches above floor, is that ok? I always hear people say dont embed screws in mud bed. Your thoughts?
What's the minimum mud depth under the drain flange if working on single sheet of plywood sub-floor? I'm trying to go curbless. I have 1.5 inches of difference between the shower and the rest of the bathroom floor. The shower 72 x 38 inches, which gives me about 32 inches the long way to each wall from the edge of the drain flange. That would put me right at 1/4 slope per foot if the top of the flange is 3/4 inches off the floor. I'd have to go less than 3/4 inches of mud under the flange to make this work.
I think this drain is good but it needs a hair cather like Ebbe drains, also the finish grout around the drain is prety thick or wider than the grout on the tiles
Hello. I know it's overkill, but could I theoretically put a oatey pvc pan liner in and then put a membrane over the mudbed, if i could find the right parts to fit togather?
Forever grateful for Sal’s videos. Helped me establish skills needed for building showers and tile work. No failures since starting up in 2009.
Thanks, glad it helped
Ya he git a good channel
I've watched probably every single video of Sal building a mud pan, it never gets old watching the best in the business effortlessly build another perfect project. Thank you Sal for continuing to share your expert knowledge with us.
Wow, thank you!
You seem to be the one guy who cares more for the industry than he does being an influencer.
😊👍
The hole on the subfloor is much bigger than flofx flange drain outlet, so there is a gap between the outlet and the edge of the hole. Do you fill the gap up? Or will the gap cause mud bed movement in future?
Appreciate you Sal for making this video. Is your target drain height 1 1/4 in? What if you were on a concrete floor, would the height be less?
Usually the same, but depending on the type of mud, could be less.
Hey Sal what type of screws you used to hold down flange? Thank you again.
They are laticrete screws, the head is a bit smaller than the durock screws.
@@SalDiBlasi thank you for your quick response
Sal, im a DIYer. I see that you use multiple different systems, kerdi, latticrete. What would you recommend as the easiest system? I’m planning on doing a mud base slope to my drain and waterproofing and then tiling.
Good video! I always tape off my bottom piece with duct tape and cut it really nice to keep all the mud away from the drain. should that be done with bonding flamges to keep the mud off of the actual felt until you're ready to connect the actual membrane to it? And if so, which tape would you use?
3 bathrooms I’ve been to so far (this month) have had their drains situated flush with the wooden subfloor..
Any tips for what to do in prefloat situations - can you still prefloat or does the drain have to be redone?
I am guessing those were two stage drains, not a bonding flange type like the ones I use. They should have a preslope, liner and then final mud bed. Bonding flange has a single mud bed.
Sal, level those from diagonal corner to corner, it will be faster
😊👍
Do you have anything against slurry coating the floor before the mud instead of tar paper/wire when you’re waterproofing it anyways? Or is just a personal preference?
Supposed to be an unbonded mud bed on plywood, bonded on concrete.
@@SalDiBlasithe drypack youre using, where from? What brand?
Good video
What material is on those walls? Are you putting sheet membrane over that?
New waterproof board, not available just yet.
Sal I see screws in your cement board lower than three inches above floor, is that ok? I always hear people say dont embed screws in mud bed. Your thoughts?
This is a bonded system has no effect on waterproofing.
Do you do anything to prevent mud from going in the hole of the subfloor?
If the hole is the correct size, it's not a problem
What's the minimum mud depth under the drain flange if working on single sheet of plywood sub-floor? I'm trying to go curbless. I have 1.5 inches of difference between the shower and the rest of the bathroom floor. The shower 72 x 38 inches, which gives me about 32 inches the long way to each wall from the edge of the drain flange. That would put me right at 1/4 slope per foot if the top of the flange is 3/4 inches off the floor. I'd have to go less than 3/4 inches of mud under the flange to make this work.
You want a inch of mud there but you could get away with like 7/8 and 1/8 per foot slope
I think this drain is good but it needs a hair cather like Ebbe drains, also the finish grout around the drain is prety thick or wider than the grout on the tiles
Hello. I know it's overkill, but could I theoretically put a oatey pvc pan liner in and then put a membrane over the mudbed, if i could find the right parts to fit togather?
Don't do that.
@@SalDiBlasiOkay.