I just repaired a printer that despite the fact I've never touched or been trained on one, my company scheduled me to fix because of this video. Thanks so much, dude.
Straight up thank you for turning the music off at the roller part. The first time I ever did a maintenance kit on a printer like this (forget the model, but it was one of these), I thought it was going to be simple. I broke the clip and ended up needed to get a tech from Lexmark (probably one of their subcons) out to fix it. He was quite clear that this was the absolute most common issue he encounters by a very wide margin.
FYI,,, you should not remove the paper cover on the transfer roller until it is inserted into place, otherwise you could accidentally touch the sponge roller and contaminate it with the oils from your fingers.
Good point. I just did this job today at my work & I accidentally touched it but barely and it was just on the outer side edge. Works fine for now… but if I have to do it again, I’m following your advice.
One of my least favorite tasks at work. I really didn't miss doing this at all. It's been a while since I have done this and I had to come back here to look up where one of the parts goes. LOL
The MS510 is a little more tricky as he side covers have to come off to route a solenoid/cable to the system board, if you're not technically savvy I'd leave that to a trained tech
Don't you also need to reset the "Roller Count"? And YES, leave the paper on the Transfer Roller until you have it installed in the printer to avoid getting oils from your hands on the roller.
Great question! Each maintenance kit has a microchip inside that communicates with the printer. That's how the printer knows when a new one is installed. If you have any further questions about how this works, feel free to give us a call at 480-463-4548 and we'd love to help!
Press 2 and 6 buttons then turn on the printer. keep pressed for about 10 seconds. scroll to reset roller count. press up to exit config menu. restart printer. done.
I just repaired a printer that despite the fact I've never touched or been trained on one, my company scheduled me to fix because of this video.
Thanks so much, dude.
Same boat. This video saved me!
Straight up thank you for turning the music off at the roller part.
The first time I ever did a maintenance kit on a printer like this (forget the model, but it was one of these), I thought it was going to be simple. I broke the clip and ended up needed to get a tech from Lexmark (probably one of their subcons) out to fix it. He was quite clear that this was the absolute most common issue he encounters by a very wide margin.
Just off to do this procedure and watched this Video for a re fresh. Very helpful and clear to follow. Well done
Luv'd the jazz tunes!
This was great. I completed the job quickly. Thanks guys!
FYI,,, you should not remove the paper cover on the transfer roller until it is inserted into place, otherwise you could accidentally touch the sponge roller and contaminate it with the oils from your fingers.
Good point. I just did this job today at my work & I accidentally touched it but barely and it was just on the outer side edge. Works fine for now… but if I have to do it again, I’m following your advice.
Well done. Fantastic guide.
Thanks Lisa!
`great video tnx
Thank you, you saved my life! :)
One of my least favorite tasks at work. I really didn't miss doing this at all. It's been a while since I have done this and I had to come back here to look up where one of the parts goes. LOL
Hello everyone! I am looking for the fuser chip reset program. Does anyone has it?
Thank you for helping
Thank you for your valued information............ would you be able to list out the Maintenance kit for Lexmark MS817n?
The MS817 is the same process as this video
Second video I watched and neither said when to change kit, page count?
Спасибо
How much does this part cost?
Is this the same for the MS510? Any videos/instructions/suggestions about that printer?
The MS510 is a little more tricky as he side covers have to come off to route a solenoid/cable to the system board, if you're not technically savvy I'd leave that to a trained tech
is MS510dn similar?
Don't you also need to reset the "Roller Count"? And YES, leave the paper on the Transfer Roller until you have it installed in the printer to avoid getting oils from your hands on the roller.
Yes, I couple more minutes for that would help
Everyone's a critic. Make your own video bub
Do you have a video to replace a the printhead (laser unit)
Great... but how does the printer know?
Great question! Each maintenance kit has a microchip inside that communicates with the printer. That's how the printer knows when a new one is installed. If you have any further questions about how this works, feel free to give us a call at 480-463-4548 and we'd love to help!
Press 2 and 6 buttons then turn on the printer. keep pressed for about 10 seconds. scroll to reset roller count. press up to exit config menu. restart printer. done.
I0
The music was DREADFUL. Please change it.
The video was great otherwise.